Home › Drivetrain › JF2A (TRANSFER / 4WD / AWD) › TRANSFER SYSTEM › from 2015.08
RM2660E _52 Drivetrain _052810 JF2A TRANSFER / 4WD / AWD _0255329 TRANSFER SYSTEM C

JF2A TRANSFER / 4WD / AWD  TRANSFER SYSTEM  P163B  4WD ECU Malfunction  


DESCRIPTION

This DTC is output when a malfunction is detected in the 4 wheel drive control ECU internal circuit.

DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P163B
1.

While the ignition switch is turned to ON or directly after the ignition switch is turned to ON

2.

4 wheel drive control ECU internal circuit malfunction

3.

0.5 seconds or more (if directly after the ignition switch is turned to ON, 0.05 seconds or more)

4.

1 trip detection logic


·

Wire harness and connector

·

Transfer shift actuator assembly

·

Differential lock shift actuator*

·

4 wheel drive control ECU



*: w/ Rear Differential Lock


WIRING DIAGRAM

C341640E04
4.531,7.417 4.865,7.646 0.333,0.229 10 false A28 4.938,7.417 6.708,7.573 1.771,0.156 10 false 4 Wheel Drive Control ECU 4.396,2.063 4.917,2.344 0.521,0.281 10 false TM1 4.375,2.74 4.896,3.021 0.521,0.281 10 false TM2 4.167,2.063 4.531,2.354 0.365,0.292 10 false 8 4.167,2.719 4.531,3.01 0.365,0.292 10 false 7 2.115,1.292 2.635,1.573 0.521,0.281 10 false TM1 2.135,1.958 2.656,2.24 0.521,0.281 10 false TM2 2.531,1.385 2.927,1.594 0.396,0.208 10 false C37 2.542,2.052 2.938,2.26 0.396,0.208 10 false C37 0.604,3.75 1.802,4.396 1.198,0.646 10 false High-low Transfer Shift Motor 0.542,1.573 1.729,2.083 1.188,0.51 10 false Center Differential Lock Shift Motor 0.552,4.646 2.292,4.865 1.74,0.219 10 false High-low Transfer Actuator 0.344,2.51 2.469,3.021 2.125,0.51 10 false Center Differential Lock Actuator 0.448,5.125 2.729,5.333 2.281,0.208 10 false Transfer Shift Actuator Assembly 0.594,7.115 2.708,7.354 2.115,0.24 10 false Differential Lock Shift Actuator* 0.615,6.01 1.792,6.552 1.177,0.542 10 false Differential Lock Shift Motor 0.188,7.375 1.927,7.604 1.74,0.229 10 false *: w/ Rear Differential Lock 4.354,3.458 4.875,3.74 0.521,0.281 10 false HM1 4.385,4.156 4.906,4.438 0.521,0.281 10 false HM2 4.188,3.458 4.448,3.656 0.26,0.198 10 false 2 4.198,4.156 4.563,4.448 0.365,0.292 10 false 6 2.531,3.583 2.927,3.792 0.396,0.208 10 false C38 2.531,4.25 2.927,4.458 0.396,0.208 10 false C38 0.406,7.115 0.646,7.292 0.24,0.177 10 false f1 4.385,4.833 4.906,5.115 0.521,0.281 10 false M1 4.365,5.49 4.885,5.771 0.521,0.281 10 false M2 4.177,4.833 4.344,5.01 0.167,0.177 10 false 3 4.188,5.49 4.354,5.667 0.167,0.177 10 false 9 2.531,5.833 2.698,6.01 0.167,0.177 10 false 3 2.542,6.5 2.729,6.698 0.188,0.198 10 false 2 5.5,0.75 5.875,1.021 0.375,0.271 10 false IG 6.198,5.781 6.573,6.052 0.375,0.271 10 false IG 2.604,1.854 2.875,2.052 0.271,0.198 10 false 2 2.604,1.208 2.875,1.406 0.271,0.198 10 false 1 2.615,4.042 2.885,4.24 0.271,0.198 10 false 2 2.604,3.354 2.875,3.552 0.271,0.198 10 false 1 2.146,3.479 2.667,3.76 0.521,0.281 10 false HM1 2.146,4.156 2.479,4.354 0.333,0.198 10 false HM2 3.427,4.885 3.615,5.094 0.188,0.208 12 false * 3.479,5.531 3.667,5.74 0.188,0.208 12 false * 5.427,2.438 5.948,2.719 0.521,0.281 10 false RLY1-1 5.427,3.135 5.948,3.417 0.521,0.281 10 false RLY1-2 5.427,5.177 5.948,5.458 0.521,0.281 10 false RLY2-1 5.427,5.854 5.948,6.135 0.521,0.281 10 false RLY2-2 2.188,5.802 2.708,6.083 0.521,0.281 10 false M1 2.188,6.479 2.708,6.76 0.521,0.281 10 false M2

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU AND TRANSFER SHIFT ACTUATOR ASSEMBLY - BODY GROUND)
a.

Disconnect the A28 4 wheel drive control ECU connector.


b.

Disconnect the C37 transfer shift actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-8 (TM1) or C37-2 (TM1) - Body ground Always 10 kΩ or higher
A28-7 (TM2) or C37-1 (TM2) - Body ground Always 10 kΩ or higher




OK

2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU AND TRANSFER SHIFT ACTUATOR ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU AND TRANSFER SHIFT ACTUATOR ASSEMBLY - BODY GROUND)
a.

Disconnect the A28 4 wheel drive control ECU connector.


b.

Disconnect the C38 transfer shift actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-2 (HM1) or C38-1 (HM1) - Body ground Always 10 kΩ or higher
A28-6 (HM2) or C38-2 (HM2) - Body ground Always 10 kΩ or higher




OK

3.INSPECT TRANSFER SHIFT ACTUATOR ASSEMBLY (CENTER DIFFERENTIAL LOCK SHIFT MOTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT TRANSFER SHIFT ACTUATOR ASSEMBLY (CENTER DIFFERENTIAL LOCK SHIFT MOTOR)
C339631E02
0.121,0 0.509,0.239 0.387,0.239 10 *a 0.184,0.878 0.535,1.145 0.350,0.267 10 *b 2.213,1.153 1.754,1.645 false 1.521,1.652 1.931,1.862 0.411,0.209 10 TM2 2.266,1.641 2.676,1.850 0.411,0.209 10 TM1 2.411,1.149 2.463,1.614 false

a.

Disconnect the C37 transfer shift actuator assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (TM1) - 2 (TM2) Always 1.5 to 100 Ω


Text in Illustration
*a Component without harness connected
(Transfer Shift Actuator Assembly)
*b Center Differential Lock Actuator Side



OK

4.INSPECT TRANSFER SHIFT ACTUATOR ASSEMBLY (HIGH-LOW TRANSFER SHIFT MOTOR)

NG

REPLACE TRANSFER SHIFT ACTUATOR ASSEMBLY

4.INSPECT TRANSFER SHIFT ACTUATOR ASSEMBLY (HIGH-LOW TRANSFER SHIFT MOTOR)
C339630E02
0.127,0 0.663,0.313 0.536,0.313 10 *a 0.419,0.966 0.719,1.196 0.300,0.230 10 *b 2.114,1.184 1.834,1.746 false 1.582,1.746 1.979,1.948 0.397,0.202 10 HM2 2.326,1.208 2.761,1.644 false 2.591,1.705 2.987,1.908 0.397,0.202 10 HM1

a.

Disconnect the C38 transfer shift actuator assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (HM1) - 2 (HM2) Always 1.5 to 100 Ω


Text in Illustration
*a Component without harness connected
(Transfer Shift Actuator Assembly)
*b High-low Transfer Actuator Side


Result:
Result Proceed to
OK (w/ Rear Differential Lock) A
OK (w/o Rear Differential Lock) B
NG C



A

5.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU AND DIFFERENTIAL LOCK SHIFT ACTUATOR - BODY GROUND)

B

C

REPLACE TRANSFER SHIFT ACTUATOR ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU AND DIFFERENTIAL LOCK SHIFT ACTUATOR - BODY GROUND)
a.

Disconnect the A28 4 wheel drive control ECU connector.


b.

Disconnect the f1 differential lock shift actuator connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-3 (M1) - f1-3 (M1) Always Below 1 Ω
A28-9 (M2) - f1-2 (M2) Always Below 1 Ω
A28-3 (M1) or f1-3 (M1) - Body ground Always 10 kΩ or higher
A28-9 (M2) or f1-2 (M2) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A28-3 (M1) or f1-3 (M1) - Body ground Always Below 1 V
A28-9 (M2) or f1-2 (M2) - Body ground Always Below 1 V




OK

6.INSPECT DIFFERENTIAL LOCK SHIFT ACTUATOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT DIFFERENTIAL LOCK SHIFT ACTUATOR
a.

Disconnect the f1 differential lock shift actuator connector.


C341715E02
1.75,0.708 2.24,0.323 true 0.865,1.042 1.323,0.813 true 0.125,0.094 0.521,0.323 0.396,0.229 10 false *a 2.292,0.198 2.594,0.385 0.302,0.188 10 false M2 0.604,0.99 0.885,1.177 0.281,0.188 10 false M1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (M1) - 2 (M2) Always 100 Ω or less
3 (M1) or 2 (M2) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Differential Lock Shift Actuator)


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (M1) or 2 (M2) - Body ground Ignition switch ON Below 1 V




OK

NG