Home › Drivetrain › JF2A (TRANSFER / 4WD / AWD) › TRANSFER SYSTEM › from 2015.08
RM2660E _52 Drivetrain _052810 JF2A TRANSFER / 4WD / AWD _0255329 TRANSFER SYSTEM C

JF2A TRANSFER / 4WD / AWD  TRANSFER SYSTEM  P17DF  Center Differential Lock Limit SW Circuit  


DESCRIPTION

When the transfer shift actuator assembly is switching between free and lock, the TL2 and TL3 terminals are in one of the ON/OFF combinations listed in the table below.

Terminal Mode
FREE Switching LOCK
TL2 OFF ON ON
TL3 ON ON OFF

A malfunction is detected depending on the combination of the 2 circuits that make up the center differential lock limit switch.

DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P17DF
1.

When switching between free and lock (center differential lock shift motor operating) while the ignition switch is turned to ON or directly after the ignition switch is turned to ON

2.

The combination of TL2 and TL3 does not match

3.

0.05 seconds or more (if directly after ignition switch is turned to ON, 1 second or more)

4.

1 trip detection logic


·

Wire harness and connector

·

4 wheel drive control ECU

·

Transfer shift actuator assembly



WIRING DIAGRAM

C339925E03
1.427,2.344 3.25,2.677 1.823,0.333 10 false Center Differential Lock Limit Switch 1.177,3.229 3.302,3.563 2.125,0.333 10 false Transfer Shift Actuator Assembly 1.156,3.031 1.615,3.26 0.458,0.229 10 false C37 3.094,1.323 3.417,1.552 0.323,0.229 10 false TL2 3.115,1.99 3.542,2.271 0.427,0.281 10 false TL3 3.427,1.313 3.719,1.49 0.292,0.177 10 false 6 3.417,1.99 3.635,2.24 0.219,0.25 10 false 5 1.198,1.99 1.75,2.229 0.552,0.24 10 false GND1 1.031,1.99 1.25,2.156 0.219,0.167 10 false 7 4.792,3.24 6.75,3.5 1.958,0.26 10 false 4 Wheel Drive Control ECU 4.771,3.031 5.125,3.229 0.354,0.198 10 false A27 4.75,1.292 5.021,1.438 0.271,0.146 10 false 10 4.979,1.99 5.406,2.271 0.427,0.281 10 false TL3 4.969,1.302 5.292,1.531 0.323,0.229 10 false TL2 4.813,1.979 5.135,2.188 0.323,0.208 10 false 9 5.677,0.313 6.052,0.594 0.375,0.281 10 false IG

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - TRANSFERSHIFT ACTUATOR ASSEMBLY)
a.

Disconnect the A27 4 wheel drive control ECU connector.


b.

Disconnect the C37 transfer shift actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A27-10 (TL2) - C37-6 (TL2) Always Below 1 Ω
A27-9 (TL3) - C37-5 (TL3) Always Below 1 Ω
C37-7 (GND1) - Body ground Always Below 1 Ω
A27-10 (TL2) or C37-6 (TL2) - Body ground Always 10 kΩ or higher
A27-9 (TL3) or C37-5 (TL3) - Body ground Always 10 kΩ or higher




OK

2.CHECK 4 WHEEL DRIVE CONTROL ECU (ECU OUTPUT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK 4 WHEEL DRIVE CONTROL ECU (ECU OUTPUT VOLTAGE)
U165681E01
1.686,0.181 2.040,0.347 0.354,0.166 10 C37 2.144,1.21 2.367,1.657 false 2.217,1.713 2.664,1.945 0.448,0.232 10 TL2 1.422,1.64 1.763,1.840 0.341,0.200 10 TL3 1.911,1.22 1.611,1.64 false 0.116,0.024 0.459,0.308 0.343,0.284 10 *a

a.

Disconnect the C37 transfer shift actuator assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C37-6 (TL2) - Body ground Ignition switch ON 10 to 14 V
C37-5 (TL3) - Body ground Ignition switch ON 10 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Transfer Shift Actuator Assembly)

Result:
Result Proceed to
OK A
NG for LHD B
for RHD C




A

REPLACE TRANSFER SHIFT ACTUATOR ASSEMBLY

B

C