Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB › from 2015.08
RM2660E _52 Drivetrain _052812 AXLE AND DIFFERENTIAL _0255361 FRONT AXLE HUB A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedures for the LH side and RH side.

·

The procedures listed below are for the LH side.



PROCEDURE

Hide 43502C 1.INSTALL FRONT AXLE HUB SUB-ASSEMBLY LH

a.

Apply MP grease to a new O-ring.


b.

Install the O-ring to the axle hub.

NOTICE:

Do not damage the O-ring.



c.

Connect the front drive shaft to the front axle hub.

NOTICE:

Be careful not to damage the front drive shaft boot.



d.
C171978

Install the dust cover and axle hub to the steering knuckle with the 4 bolts.

Torque:
99 N*m (1010 kgf*cm, 73 ft.*lbf)


Hide 3.CONNECT FRONT DISC BRAKE CALIPER ASSEMBLY LH

a.
C171974

Connect the front disc brake caliper and install 2 new bolts.

Torque:
180 N*m (1835 kgf*cm, 133 ft.*lbf)

NOTICE:
·

Do not twist the flexible hose.

·

Make sure that the bolts are free from damage and foreign matter.

·

Do not overtighten the bolts.




Hide 43502H 4.INSTALL FRONT AXLE SHAFT NUT LH

a.

Clean the threaded parts on the drive shaft and axle shaft nut using a non-residue solvent.

NOTICE:
·

Be sure to perform this work for a new drive shaft.

·

Keep the threaded parts free of oil and foreign objects.




b.
C171977

Using a 39 mm socket wrench, install the axle shaft nut.

Torque:
200 N*m (2039 kgf*cm, 148 ft.*lbf)


c.

Using a 39 mm socket wrench, loosen the axle shaft nut.


d.

Using a 39 mm socket wrench, retighten the axle shaft nut.

Torque:
340 N*m (3467 kgf*cm, 251 ft.*lbf)


e.
C171976

Install the front wheel adjusting lock cap and a new cotter pin.


Hide 5.DISCONNECT FRONT DISC BRAKE CALIPER ASSEMBLY LH

a.
C171974

Remove the 2 bolts and disconnect the disc brake caliper from the steering knuckle.

NOTICE:
·

Do not disconnect the flexible hose from the disc brake caliper.

·

Do not twist or bend the flexible hose.




Hide 43512 6.REMOVE FRONT DISC

Hide 7.INSPECT FRONT AXLE HUB

Hide 43514C 8.INSTALL FRONT AXLE HUB GREASE CAP LH

a.

Install the axle hub grease cap.

NOTICE:

Make sure to securely fit the grease cap to the axle hub.



Hide 10.CONNECT FRONT DISC BRAKE CALIPER ASSEMBLY LH

a.
C171974

Connect the front disc brake caliper and install 2 new bolts.

Torque:
180 N*m (1835 kgf*cm, 133 ft.*lbf)

NOTICE:
·

Do not twist the flexible hose.

·

Make sure that the bolts are free from damage and foreign matter.

·

Do not overtighten the bolts.




b.
C171973E05
2.135,0.698 2.531,0.927 0.396,0.229 10 true Nut 0.771,0.49 1.198,0.719 0.427,0.229 10 true Bolt

Connect the brake tube bracket to the steering knuckle with the bolt and nut.

Torque:
for bolt : 31 N*m (316 kgf*cm, 23 ft.*lbf)
for nut : 13 N*m (132 kgf*cm, 10 ft.*lbf)


Hide 11.INSTALL FRONT WHEEL

Torque:
for Aluminum Wheel : 131 N*m (1336 kgf*cm, 97 ft.*lbf)
for Steel Wheel : 209 N*m (2131 kgf*cm, 154 ft.*lbf)

Hide 48860D 13.CLOSE STABILIZER CONTROL WITH ACCUMULATOR HOUSING SHUTTER VALVE (w/ KDSS)

Hide 48826D 14.INSTALL STABILIZER CONTROL VALVE PROTECTOR (w/ KDSS)