Home › Suspension › SUSPENSION CONTROL › ACTIVE HEIGHT CONTROL SUSPENSION › 2014.08–2015.08
RM2660E _53 Suspension _052813 SUSPENSION CONTROL _0255367 ACTIVE HEIGHT CONTROL SUSPENSION C

SUSPENSION CONTROL  ACTIVE HEIGHT CONTROL SUSPENSION  C1763  Abnormal Pump Motor Oil Pressure  


DESCRIPTION

DTC Code Detection Condition Trouble Area
C1763 When either of the following conditions is met:
·

While the motor relay is in operation, the condition that the fluid pressure is 0.6 MPa (6.1 kgf/cm2, 87 psi) or less continues for 0.6 seconds.

·

When the vehicle is climbing a slope, no changes are detected in the fluid pressure for 8 seconds 3 times consecutively.


·

Fluid level low

·

Harness or connector

·

Suspension control relay

·

Height control pump and motor

·

Suspension control ECU



WIRING DIAGRAM

C176979E01
1.481,2.786 3.567,3.025 2.086,0.239 10 Height Control Pump and Motor 4.987,2.217 6.633,2.502 1.646,0.286 10 Suspension Control ECU 5.37,0.535 5.665,0.774 0.295,0.239 10 RC 5.011,0.395 5.237,0.621 0.225,0.225 10 16 1.607,3.272 2.429,3.442 0.823,0.170 10 from Battery 2.548,1.334 4.245,1.546 1.697,0.211 10 Suspension Control (AHC) 4.987,2.027 5.323,2.197 0.336,0.170 10 K36 3.996,0.402 4.155,0.559 0.159,0.158 10 1 4.013,0.791 4.203,0.935 0.189,0.144 10 5 2.654,0.423 2.852,0.583 0.198,0.159 10 2 2.652,0.798 2.837,0.959 0.185,0.161 10 3 1.656,1.871 1.784,2.032 0.128,0.161 10 2 1.649,2.203 1.773,2.379 0.123,0.176 10 1 1.481,2.626 1.748,2.789 0.267,0.163 10 L36

CAUTION / NOTICE / HINT

NOTICE:
·

Before performing troubleshooting, inspect the connectors of related circuits.

·

If the suspension control ECU or height control sensor is replaced, the vehicle height offset calibration must be performed (See page Suspension>SUSPENSION CONTROL>ACTIVE HEIGHT CONTROL SUSPENSION>INITIALIZATION).



PROCEDURE

1.CHECK FOR DTC

Result:
Result Proceed to
C1763 only is output A
C1718 is output simultaneously B



A

2.INSPECT FOR FLUID LEAK

B

2.INSPECT FOR FLUID LEAK
a.

Inspect for fluid leaks (See page Suspension>SUSPENSION CONTROL>SUSPENSION CONTROL SYSTEM>ON-VEHICLE INSPECTION).

OK:

No fluid leakage.




OK

3.INSPECT SUSPENSION CONTROL RELAY (AHC)

NG

REPAIR FLUID LEAK OR REPLACE LEAKING PART(S)

3.INSPECT SUSPENSION CONTROL RELAY (AHC)
a.

Remove the suspension control relay from the engine room relay block.


b.
C149624E01
1.283,0.718 1.439,0.874 0.156,0.156 10 5 1.282,1.272 1.438,1.427 0.156,0.156 10 2 0.24,0.722 0.396,0.877 0.156,0.156 10 3 0.235,1.285 0.391,1.441 0.156,0.156 10 1 3.167,0.968 3.323,1.124 0.156,0.156 10 5 1.969,1.701 2.125,1.857 0.156,0.156 10 2 1.393,0.974 1.549,1.130 0.156,0.156 10 3 2.699,0.245 2.854,0.400 0.156,0.156 10 1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminal 1 and 2 10 kΩ or higher
Battery voltage is applied to terminal 1 and 2 Below 1 Ω




OK

4.CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - RELAY (AHC) AND BODY GROUND)

NG

REPLACE SUSPENSION CONTROL RELAY

4.CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - RELAY (AHC) AND BODY GROUND)
U164845E02
4.667,2.115 5.167,2.344 5.167,2.344 5.24,2.344 false 2.833,1.438 3.156,1.438 false 2.625,1.458 2.625,1.875 false 4.135,0.094 6.5,0.448 2.365,0.354 10 false Rear view of wire harness connector: (to Suspension Control ECU) 0.271,0.094 3.063,0.677 2.792,0.583 10 false Component without suspension control relay: (Engine Room Relay Block) 3.969,1.854 4.271,2.01 0.302,0.156 10 false K36 5.271,2.26 5.813,2.469 0.542,0.208 10 false 16 (RC) 3.198,1.344 3.365,1.51 0.167,0.167 10 false 1 2.615,1.865 2.802,2.021 0.188,0.156 10 false 2

a.

Remove the suspension control relay from the engine room relay block.


b.

Disconnect the K36 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K36-16 (RC) - Relay block suspension control relay terminal 1 Always Below 1 Ω
K36-16 (RC) - Body ground Always 10 kΩ or higher
Relay block suspension control relay terminal 2 - Body ground Always Below 1 Ω




OK

5.CHECK HARNESS AND CONNECTOR (BATTERY - SUSPENSION CONTROL RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (BATTERY - SUSPENSION CONTROL RELAY)
a.

Remove the suspension control relay from the engine room relay block.


b.
C177031E01
0.098,0.231 2.763,0.818 2.665,0.586 10 Component without suspension control relay: (Engine Room Relay Block) 2.998,1.412 3.137,1.570 0.138,0.158 10 5 2.797,1.788 2.898,1.49 2.898,1.49 2.967,1.49 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Relay block suspension control relay terminal 5 - Body ground Always 11 to 14 V




OK

6.CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL RELAY - PUMP AND MOTOR AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL RELAY - PUMP AND MOTOR AND BODY GROUND)
a.

Remove the suspension control relay from the engine room relay block.


b.

Disconnect the L36 pump and motor connector.


c.

Measure the resistance according to the value(s) in the table below.

U164846E02
2.729,1.552 2.729,1.917 false 3.74,0.125 6.344,0.479 2.604,0.354 10 false Front view of wire harness connector: (to Height Control Pump and Motor) 0.271,0.125 3.063,0.708 2.792,0.583 10 false Component without suspension control relay: (Engine Room Relay Block) 2.698,1.948 2.823,2.135 0.125,0.188 10 false 3 3.979,1.844 4.25,2.01 0.271,0.167 10 false L36

Standard Resistance:
Tester Connection Condition Specified Condition
Relay block suspension control relay terminal 3 - L36-2 Always Below 1 Ω
Relay block suspension control relay terminal 3 - Body ground Always 10 kΩ or higher
L36-1 - Body ground Always Below 1 Ω




OK

7.CHECK OPERATION OF HEIGHT CONTROL PUMP AND MOTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK OPERATION OF HEIGHT CONTROL PUMP AND MOTOR
a.
C177053E01
0.201,0.116 2.736,0.702 2.534,0.586 10 Component without harness connected: (Height Control Pump and Motor) 2.792,2.595 2.883,2.797 0.091,0.202 10 - 0.465,2.618 0.584,2.866 0.119,0.248 10 + 1.396,2.114 0.525,2.469 0.525,2.469 0.525,2.549 false 2.061,2.103 2.828,2.457 2.828,2.457 2.828,2.56 false

Remove the height control pump and motor (See page Suspension>SUSPENSION CONTROL>ACTIVE HEIGHT CONTROL PUMP AND MOTOR>REMOVAL).


b.

Apply battery voltage to the height control pump and motor and check the operation of the motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1
Motor operates


NOTICE:
·

Be careful of fluid spray when the height control pump and motor is operating.

·

Do not allow the motor to operate for 60 seconds or more.

·

If the height control pump and motor is shorted, locked, or has a similar type of malfunction, a large amount of current will be flowing. Therefore, if the motor does not operate, immediately stop this inspection.





OK

REPLACE SUSPENSION CONTROL ECU

NG

REPLACE HEIGHT CONTROL PUMP AND MOTOR