Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255415 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1432  Steering Angle Sensor Power Source Voltage Malfunction  


DESCRIPTION

Steering sensor signals are sent to the skid control ECU (master cylinder solenoid) via the CAN communication system. When there is a malfunction in the CAN communication system, it is detected by the steering sensor zero point malfunction diagnostic function.

DTC Code DTC Detection Condition Trouble Area
C1432 A steering sensor power supply malfunction signal is received from the steering sensor.
·

J/B-B NO. 1 fuse

·

ECU-IG NO. 1 fuse

·

Steering sensor power supply

·

Steering sensor

·

VGRS ECU (Steering control ECU)*



*: w/ VGRS System


WIRING DIAGRAM

C349421E03
0.385,3.365 0.76,3.542 0.375,0.177 10 false A24 0.365,3.542 3.271,3.781 2.906,0.24 10 false Skid Control ECU (Master Cylinder Solenoid) 4.594,3.594 5.188,3.802 0.594,0.208 10 false E121*1 4.594,3.781 5.188,3.99 0.594,0.208 10 false E163*2 4.594,3.948 5.688,4.177 1.094,0.229 10 false Steering Sensor 4.875,2.833 5.083,3.052 0.208,0.219 10 false IG 5,2.563 5.146,2.729 0.146,0.167 10 false 4 3.083,2.542 4.021,2.719 0.938,0.177 10 false ECU-IG NO. 1 1.302,2.385 2.313,2.635 1.01,0.25 10 false from IG Circuit 1.156,0.333 1.979,0.573 0.823,0.24 10 false from Battery 2.323,0.479 3.156,0.677 0.833,0.198 10 false J/B-B NO. 1 2.896,1.635 5.354,1.844 2.458,0.208 10 false VGRS ECU (Steering Control ECU)*2 4.719,1.146 5.031,1.313 0.313,0.167 10 false +BO 5.135,1.031 5.292,1.219 0.156,0.188 10 false 1 3.323,0.646 3.479,0.833 0.156,0.188 10 false *2 4.385,0.167 4.542,0.354 0.156,0.188 10 false *1 5.813,2.833 6.125,3.031 0.313,0.198 10 false BAT 6.031,2.563 6.219,2.74 0.188,0.177 10 false 5 5.938,3.198 6.292,3.406 0.354,0.208 10 false ESS 6.406,3.063 6.604,3.26 0.198,0.198 10 false 1 0.292,4.833 1.969,5.115 1.677,0.281 10 false *1: w/o VGRS System 0.042,0.042 2.333,0.292 2.292,0.25 12 false w/ Entry and Start System: 0.292,5.135 1.844,5.458 1.552,0.323 10 false *2: w/ VGRS System 0.885,4.385 2.927,4.615 2.042,0.229 10 false : CAN Communication System 2.885,1.427 3.313,1.615 0.427,0.188 10 false E161 3.875,1.146 4.198,1.365 0.323,0.219 10 false +BI 3.615,1.021 3.792,1.208 0.177,0.188 10 false 7 5.594,1.854 5.75,2.042 0.156,0.188 10 false *2

C283803E09
1.177,2.021 2.146,2.208 0.969,0.188 10 false from IG Circuit 1.313,1.583 2.104,1.781 0.792,0.198 10 false from Battery 2.594,2.156 3.521,2.333 0.927,0.177 10 false ECU-IG NO. 1 2.656,1.74 3.563,1.906 0.906,0.167 10 false J/B-B NO. 1 3.802,1.5 3.958,1.698 0.156,0.198 10 false 6 4.01,1.979 4.323,2.177 0.313,0.198 10 false IG 3.813,1.885 3.969,2.083 0.156,0.198 10 false 5 3.99,1.563 4.479,1.771 0.49,0.208 10 false BAT 3.813,2.281 3.969,2.479 0.156,0.198 10 false 2 3.99,2.365 4.448,2.563 0.458,0.198 10 false ESS 3.958,2.781 4.417,2.979 0.458,0.198 10 false E181 3.948,2.969 4.958,3.24 1.01,0.271 10 false Steering Sensor 0.771,3.188 2.896,3.458 2.125,0.271 10 false : CAN Communication System 5.521,2.042 5.896,2.271 0.375,0.229 10 false A24 5.5,2.229 7.146,2.781 1.646,0.552 10 false Skid Control ECU (Master Cylinder Solenoid) 0.292,0.406 2.594,0.708 2.302,0.302 12 false w/o Entry and Start System:

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the steering sensor, confirm that the replacement part is of the correct specification.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

When the speed sensor or the yaw rate and acceleration sensor (airbag sensor assembly) has trouble, DTCs for the steering sensor may be stored even when the steering sensor is normal. When DTCs for the speed sensor or yaw rate and acceleration sensor (airbag sensor assembly) are output together with DTCs for the steering sensor, inspect and repair the speed sensor and yaw rate and acceleration sensor (airbag sensor assembly) first, and then inspect and repair the steering sensor.


PROCEDURE

1.CHECK DTC (CAN COMMUNICATION SYSTEM)



d.

for RHD (without Central Gateway ECU):

Check for DTCs (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD without Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

Result
Result Proceed to
CAN DTC is not output A
CAN DTC is output (for LHD (with Central Gateway ECU)) B
CAN DTC is output (for LHD (without Central Gateway ECU)) C
CAN DTC is output (for RHD (with Central Gateway ECU)) D
CAN DTC is output (for RHD (without Central Gateway ECU)) E



A

2.CHECK HARNESS AND CONNECTOR (IG/ESS TERMINAL)

B

C

D

E

2.CHECK HARNESS AND CONNECTOR (IG/ESS TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness in the locking part and connecting part of the connectors.


c.

w/o Entry and Start System:

Disconnect the steering sensor connector.


U165758E02
1.354,1.156 1.354,1.573 1.354,1.573 1.219,1.573 true 2.083,1.167 2.083,1.583 2.083,1.583 2.229,1.583 true 0.25,0.833 0.677,1.042 0.427,0.208 10 false E181 0.125,0.104 0.396,0.344 0.271,0.24 10 false *a 2.292,1.51 2.51,1.677 0.219,0.167 10 false IG 0.865,1.49 1.188,1.719 0.323,0.229 10 false ESS

d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E181-5 (IG) - Body ground Ignition switch ON 11 to 14 V



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E181-2 (ESS) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Steering Sensor)

f.

w/ Entry and Start System:

Disconnect the steering sensor connector.


U165445E02
1.906,1.469 2.667,1.625 2.667,1.625 2.667,1.75 true 1.302,1.458 0.583,1.5 0.583,1.5 0.583,1.615 true 1.896,3.604 2.604,3.646 2.604,3.646 2.604,3.76 true 1.281,3.604 0.563,3.646 0.563,3.646 0.563,3.771 true 0.135,0.188 0.469,0.458 0.333,0.271 10 false *a 2,0.26 2.333,0.531 0.333,0.271 10 false *A 2.031,2.385 2.365,2.656 0.333,0.271 10 false *B 1.542,0.344 1.917,0.521 0.375,0.177 10 false E121 2.594,1.771 2.948,2.01 0.354,0.24 10 false IG 0.417,1.677 0.781,1.885 0.365,0.208 10 false ESS 1.573,2.458 1.948,2.635 0.375,0.177 10 false E163 2.531,3.771 2.885,4.01 0.354,0.24 10 false IG 0.385,3.813 0.75,4.021 0.365,0.208 10 false ESS

g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/o VGRS System:
Tester Connection Switch Condition Specified Condition
E121-4 (IG) - Body ground Ignition switch ON 11 to 14 V

w/ VGRS System:
Tester Connection Switch Condition Specified Condition
E163-4 (IG) - Body ground Ignition switch ON 11 to 14 V



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o VGRS System:
Tester Connection Condition Specified Condition
E121-1 (ESS) - Body ground Always Below 1 Ω

w/ VGRS System:
Tester Connection Condition Specified Condition
E163-1 (ESS) - Body ground Always Below 1 Ω



Text in Illustration
*A w/o VGRS System
*B w/ VGRS System
*a Front view of wire harness connector
(to Steering Sensor)


OK

3.CHECK HARNESS AND CONNECTOR (BAT TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (BAT TERMINAL)
a.

Turn the ignition switch off.


b.

w/o Entry and Start System:

Disconnect the steering sensor connector.


U165759E02
2.313,1.167 2.313,1.583 2.313,1.583 2.448,1.583 true 0.26,0.823 0.698,1.021 0.438,0.198 10 false E181 0.135,0.083 0.406,0.323 0.271,0.24 10 false *a 2.542,1.5 2.99,1.76 0.448,0.26 10 false BAT

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E181-6 (BAT) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Steering Sensor)


d.

w/ Entry and Start System:

Disconnect the steering sensor connector.


U165446E02
2.052,1.458 2.813,1.615 2.813,1.615 2.813,1.74 true 2.115,3.615 2.875,3.771 2.875,3.771 2.875,3.896 true 0.188,0.156 0.521,0.427 0.333,0.271 10 false *a 2,0.292 2.333,0.563 0.333,0.271 10 false *A 2.042,2.427 2.375,2.698 0.333,0.271 10 false *B 1.542,0.344 1.917,0.521 0.375,0.177 10 false E121 1.583,2.458 2.031,2.667 0.448,0.208 10 false E163 2.708,1.75 3.073,1.958 0.365,0.208 10 false BAT 2.781,3.948 3.146,4.156 0.365,0.208 10 false BAT

e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/o VGRS System:
Tester Connection Condition Specified Condition
E121-5 (BAT) - Body ground Always 11 to 14 V

w/ VGRS System:
Tester Connection Condition Specified Condition
E163-5 (BAT) - Body ground Always 11 to 14 V


Text in Illustration
*A w/o VGRS System
*B w/ VGRS System
*a Front view of wire harness connector
(to Steering Sensor)

Result
Result Proceed to
OK A
NG (w/ VGRS System) B
NG (w/o VGRS System) C



A

B

4.CHECK HARNESS AND CONNECTOR (+BI TERMINAL)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (+BI TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the VGRS ECU (steering control ECU) connector.


U165259E02
1.177,1.302 0.781,1.635 true 1.563,0.458 1.99,0.688 0.427,0.229 10 false E161 0.51,1.604 0.76,1.75 0.25,0.146 10 false +BI 0.188,0.135 0.417,0.333 0.229,0.198 10 false *a

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E161-7 (+BI) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to VGRS ECU [Steering Control ECU])



OK

5.CHECK HARNESS AND CONNECTOR (STEERING SENSOR - STEERING CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (STEERING SENSOR - STEERING CONTROL ECU)
a.

Turn the ignition switch off.


b.

Disconnect the E163 steering sensor connector.


c.

Disconnect the E161 VGRS ECU (steering control ECU) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E163-5 (BAT) - E161-1 (+BO) Always Below 1 Ω
E163-5 (BAT) or E161-1 (+BO) - Body ground Always 10 kΩ or higher


Result
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C