Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2014.08–2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255415 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1210  Zero Point Calibration of Yaw Rate Sensor Undone  C1336  Zero Point Calibration of Acceleration Sensor Undone  


DESCRIPTION

The skid control ECU (master cylinder solenoid) receives signals from the yaw rate sensor assembly via the CAN communication system.

The yaw rate sensor assembly has a built-in acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2). If there is trouble in the bus lines between the yaw rate sensor assembly and the CAN communication system, DTCs U0123 (yaw rate sensor communication trouble) and U0124 (acceleration sensor communication trouble) are stored.

The DTCs are also stored when the calibration has not been completed.

DTC Code DTC Detection Condition Trouble Area
C1210 Zero point calibration of the yaw rate sensor is incomplete.
·

Zero point calibration incomplete

·

Sensor installation

·

Yaw rate sensor assembly

·

Skid control ECU (Master cylinder solenoid)


C1336 Zero point calibration of the acceleration sensor is incomplete.

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the master cylinder solenoid, perform zero point calibration and store the system information (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

After replacing the yaw rate sensor assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).



PROCEDURE

1.CHECK DTC (CAN COMMUNICATION SYSTEM)
a.

Check for DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
CAN DTC is not output A
CAN DTC is output (for LHD) B
CAN DTC is output (for RHD) C



A

2.PERFORM ZERO POINT CALIBRATION OF YAW RATE AND ACCELERATION SENSOR

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

C

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

2.PERFORM ZERO POINT CALIBRATION OF YAW RATE AND ACCELERATION SENSOR
a.

Perform zero point calibration of the yaw rate and acceleration sensor (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).



NEXT

3.PERFORM TEST MODE (SIGNAL CHECK)
3.PERFORM TEST MODE (SIGNAL CHECK)
a.

Turn the ignition switch off.


b.

Perform the signal check in the Test Mode Procedure (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).

OK:

All test mode DTCs are cleared.




OK

END

NG

4.CHECK YAW RATE SENSOR ASSEMBLY INSTALLATION
4.CHECK YAW RATE SENSOR ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.


b.

Check that the yaw rate sensor assembly has been installed properly (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>YAW RATE AND DECELERATION SENSOR (w/ VSC)>INSTALLATION).

OK:

The sensor is tightened to the specified torque.

The sensor is not installed at an angle.




OK

5.READ VALUE USING GTS (YAW RATE AND ACCELERATION SENSOR)

NG

5.READ VALUE USING GTS (YAW RATE AND ACCELERATION SENSOR)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Deceleration Sensor Acceleration sensor reading/ Min.: -18.525 m/s2, Max.: 18.387 m/s2 - Changes continuously during acceleration/deceleration.
Deceleration Sensor2 Acceleration sensor 2 reading/ Min.: -18.525 m/s2, Max.: 18.387 m/s2 - Changes continuously during acceleration/deceleration.
Yaw Rate Sensor Yaw rate sensor/ Min.: -128°/s, Max.: 127°/s Vehicle stationary: 0°/s
Right turn: -128 to 0°/s
Left turn: 0 to 127°/s
-


f.

Check that the yaw rate and acceleration sensor output value is displayed on the GTS.

OK:

The yaw rate and acceleration sensor output value is normal.



Result
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C


A

B

C