Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2014.08–2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255415 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1422  Master Cylinder Pressure Sensor Zero Point High Malfunction  C1456  Control Pressure Sensor Zero Point High  


DESCRIPTION

Refer to DTCs C1421, C1423, C1424, C1455, C1457 and C1458 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1281).

DTC Code DTC Detection Condition Trouble Area
C1422 When the stop light switch is off, the PM/C1 terminal voltage is 0.86 V or higher for 5 seconds or more.
·

STOP fuse

·

Stop light switch assembly

·

Stop light switch circuit

·

Master cylinder pressure sensor circuit

·

Master cylinder solenoid (Master cylinder pressure sensor)


C1456 When the stop light switch is off, the PCTRL terminal voltage is 0.86 V or higher for 5 seconds or more.
·

STOP fuse

·

Stop light switch

·

Stop light switch circuit

·

Pressure control sensor circuit

·

Master cylinder solenoid (Pressure control sensor)



CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the master cylinder solenoid, perform zero point calibration and store the system information (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.READ VALUE USING GTS (STOP LIGHT SW)

OK

2.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION

NG

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH POWER SOURCE TERMINAL)
2.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION
a.

Turn the ignition switch off.


b.

Check the brake pedal height and stop light switch installation (for LHD: See page Brake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for LHD)>ADJUSTMENT, for RHD: See page Brake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for RHD)>ADJUSTMENT).

OK:

The brake pedal height and stop light switch installation are normal.




OK

3.RECONFIRM DTC

NG

ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH

3.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more and perform a braking test (decelerate the vehicle by depressing the brake pedal).


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output (for LHD) B
DTC is output (for RHD) C



A

B

C

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH POWER SOURCE TERMINAL)
a.

Make sure that there is no looseness in the locking part and connecting part of the connectors.


b.

Disconnect the stop light switch assembly connector.


c.
U164985E01
0.232,0.198 0.482,0.479 0.250,0.281 10 *a 0.652,1.25 0.926,1.413 0.274,0.163 10 A30

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A30-2 - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)



OK

5.INSPECT STOP LIGHT SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT STOP LIGHT SWITCH
a.

Remove the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL).


b.
C215187E01
0.266,0.116 0.476,0.290 0.209,0.174 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Switch pin not pushed in Below 1 Ω
Switch pin pushed in 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Stop Light Switch Assembly)



OK

6.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C