w/o Entry and Start System
DTC C1379 is cleared when the CRAWL ON/OFF switch / CRAWL speed selector switch (suspension control switch) sends a CRAWL ON/OFF switch / CRAWL speed selector switch (suspension control switch) operation signal or when test mode ends.
w/ Entry and Start System
DTC C1379 is cleared when the CRAWL ON/OFF switch / CRAWL speed selector switch / multi-terrain select mode switch* (integration control and panel assembly) sends a CRAWL ON/OFF switch / CRAWL speed selector switch / multi-terrain select mode switch* (integration control and panel assembly) operation signal or when test mode ends.
*: w/ Multi-terrain Select
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1379 | Stored only during test mode. | ·
CRAWL ON/OFF switch / CRAWL speed selector switch (Suspension control switch)*1 ·
CRAWL ON/OFF switch / CRAWL speed selector switch / multi-terrain select mode switch*2 (integration control and panel assembly)*3 ·
Harness or connector ·
Skid control ECU (Master cylinder solenoid) |
*1: w/o Entry and Start System
*2: w/ Multi-terrain Select
*3: w/ Entry and Start System
After replacing the master cylinder solenoid, perform zero point calibration and store the system information (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).
w/o Entry and Start System:
Remove the CRAWL ON/OFF switch / CRAWL speed selector switch (suspension control switch) (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>CRAWL SWITCH(w/o Entry and Start System)>REMOVAL).
Inspect the CRAWL ON/OFF switch / CRAWL speed selector switch (suspension control switch) (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>CRAWL SWITCH(w/o Entry and Start System)>INSPECTION).
w/ Entry and Start System:
Remove the CRAWL ON/OFF switch / CRAWL speed selector switch / multi-terrain select mode switch* (integration control and panel assembly) (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>CRAWL SWITCH(w/ Entry and Start System)>REMOVAL).
Inspect the CRAWL ON/OFF switch / CRAWL speed selector switch / multi-terrain select mode switch* (integration control and panel assembly) (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>CRAWL SWITCH(w/ Entry and Start System)>INSPECTION).
*: w/ Multi-terrain Select
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/o Entry and Start System) | B |
| NG (w/ Entry and Start System) | C |
A
B
(See pageBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>CRAWL SWITCH(w/o Entry and Start System)>REMOVAL)
C
(See pageBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>CRAWL SWITCH(w/ Entry and Start System)>REMOVAL)
Disconnect the A24 skid control ECU (master cylinder solenoid) connector.
w/o Entry and Start System:
Disconnect the V4 CRAWL ON/OFF switch / CRAWL speed selector switch (suspension control switch) connector.
w/ Entry and Start System:
Disconnect the V8 CRAWL ON/OFF switch / CRAWL speed selector switch / multi-terrain select mode switch* (integration control and panel assembly) connector.
*: w/ Multi-terrain Select
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-44 (TRM1) - V4-18 (SWO2) | Always | Below 1 Ω |
| A24-44 (TRM1) - Body ground | Always | 10 kΩ or higher |
| A24-43 (TRS) - V4-14 (HSW) | Always | Below 1 Ω |
| A24-43 (TRS) - Body ground | Always | 10 kΩ or higher |
| A24-21 (TRM2) - V4-19 (ECU2) | Always | Below 1 Ω |
| A24-21 (TRM2) - Body ground | Always | 10 kΩ or higher |
| A24-13 (ATRC) - V4-13 (SWO4) | Always | Below 1 Ω |
| A24-13 (ATRC) - Body ground | Always | 10 kΩ or higher |
| V4-16 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-44 (TRM1) - V8-15 (SWO2) | Always | Below 1 Ω |
| A24-44 (TRM1) - Body ground | Always | 10 kΩ or higher |
| A24-43 (TRS) - V8-16 (HSW) | Always | Below 1 Ω |
| A24-43 (TRS) - Body ground | Always | 10 kΩ or higher |
| A24-21 (TRM2) - V8-14 (ECU2) | Always | Below 1 Ω |
| A24-21 (TRM2) - Body ground | Always | 10 kΩ or higher |
| A24-13 (ATRC) - V8-13 (SWO4) | Always | Below 1 Ω |
| A24-13 (ATRC) - Body ground | Always | 10 kΩ or higher |
| V8-10 (E) - Body ground | Always | Below 1 Ω |
OK
NG
w/o Entry and Start System:
Perform the CRAWL ON/OFF switch / CRAWL speed selector switch (suspension control switch) check in the Test Mode procedure (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).
w/ Entry and Start System:
Perform the CRAWL ON/OFF switch / CRAWL speed selector switch / multi-terrain select mode switch (integration control and panel assembly) check in the Test Mode procedure (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).
Test mode DTC C1379 is cleared.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
C