Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255415 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TRC OFF Indicator Light Remains ON  


DESCRIPTION

The TRC OFF indicator light comes on when the VSC OFF switch*1 or VSC OFF switch (integration control and panel assembly)*2 is operated.

*1: w/o Entry and Start System

*2: w/ Entry and Start System


WIRING DIAGRAM

C349671E02
5.156,2.594 6.833,2.938 1.677,0.344 10 false Skid Control ECU (Master Cylinder Solenoid) 5.156,2.375 5.458,2.542 0.302,0.167 10 false A24 2.552,1.854 3,2.031 0.448,0.177 10 false G13*1 3.01,1.854 3.458,2.031 0.448,0.177 10 false V9*2 2.573,2.281 4.896,2.698 2.323,0.417 10 false VSC OFF Switch (Integration Control and Panel Assembly)*2 2.573,2.063 4.979,2.479 2.406,0.417 10 false VSC OFF Switch*1 0.24,2.521 0.74,2.719 0.5,0.198 10 false E119 0.24,2.677 2.135,2.865 1.896,0.188 10 false Combination Meter Assembly 2.615,3.385 4.74,3.635 2.125,0.25 10 false *1: w/o Entry and Start System 4.885,3.385 6.99,3.625 2.104,0.24 10 false *2: w/ Entry and Start System 5.344,1.51 5.76,1.688 0.417,0.177 10 false CSW 5.135,1.375 5.281,1.563 0.146,0.188 10 false 9 3.917,1.5 4.063,1.688 0.146,0.188 10 false + 3.021,1.51 3.167,1.698 0.146,0.188 10 false E 4.115,1.396 4.396,1.542 0.281,0.146 10 false 6*1 4.104,1.24 4.385,1.385 0.281,0.146 10 false 7*2 2.729,1.396 3.01,1.542 0.281,0.146 10 false 3*1 2.729,1.229 3.01,1.375 0.281,0.146 10 false 5*2 0.531,3.271 2.479,3.427 1.948,0.156 10 false : CAN Communication System

CAUTION / NOTICE / HINT

NOTICE:

After replacing the master cylinder solenoid, perform zero point calibration and store the system information (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.INSPECT IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check the skid control ECU (master cylinder solenoid) connector connection.

OK:

The connector is securely connected.




OK

2.CHECK CAN COMMUNICATION LINE

NG

CONNECT CONNECTOR TO ECU CORRECTLY

4.READ VALUE USING GTS (TRC/VSC OFF MODE)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
TRC/VSC Off Mode TRC/VSC off mode/ Normal, TRC OFF, Unknown or VSC OFF Normal: Normal mode
TRC OFF: TRC OFF mode
VSC OFF: VSC OFF mode
-


f.

Check that the mode display changes according to VSC OFF switch*1 or VSC OFF switch (integration control and panel assembly)*2 operation.

*1: w/o Entry and Start System

*2: w/ Entry and Start System


OK:

Display changes according to switch operation.




OK

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

NG

5.INSPECT VSC OFF SWITCH OR INTEGRATION CONTROL AND PANEL ASSEMBLY
5.INSPECT VSC OFF SWITCH OR INTEGRATION CONTROL AND PANEL ASSEMBLY
a.

w/o Entry and Start System:

Remove the VSC OFF switch (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH(w/o Entry and Start System)>REMOVAL).


b.

w/ Entry and Start System:

Remove the VSC OFF switch (integration control and panel assembly) (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH(w/ Entry and Start System)>REMOVAL).


c.

w/o Entry and Start System:

Inspect the VSC OFF switch (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH(w/o Entry and Start System)>INSPECTION).


d.

w/ Entry and Start System:

Inspect the VSC OFF switch (integration control and panel assembly) (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH(w/ Entry and Start System)>INSPECTION).


Result
Result Proceed to
OK A
NG (w/o Entry and Start System) B
NG (w/ Entry and Start System) C


A

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)

B

C

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)
a.

Turn the ignition switch off.


b.

Disconnect the A24 skid control ECU (master cylinder solenoid) connector.


c.

Disconnect the G13 VSC OFF switch*1 or V9 VSC OFF switch (integration control and panel assembly)*2 connector.

*1: w/o Entry and Start System

*2: w/ Entry and Start System



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Entry and Start System:
Tester Connection Condition Specified Condition
A24-9 (CSW) - G13-6 (+) Always Below 1 Ω
A24-9 (CSW) - Body ground Always 10 kΩ or higher
G13-3 (E)- Body ground Always Below 1 Ω

w/ Entry and Start System:
Tester Connection Condition Specified Condition
A24-9 (CSW) - V9-7 (+) Always Below 1 Ω
A24-9 (CSW) - Body ground Always 10 kΩ or higher
V9-5 (E)- Body ground Always Below 1 Ω


Result
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C