Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255415 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1256  Accumulator Low Pressure  


DESCRIPTION

Refer to DTC C1254 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1254).

DTC Code DTC Detection Condition Trouble Area
C1256 The fluid pressure inside the accumulator is below the standard value.
·

Brake booster with accumulator pump assembly

·

Master cylinder solenoid (Accumulator pressure sensor)

·

Hydraulic brake booster assembly



CAUTION / NOTICE / HINT

NOTICE:

After replacing the master cylinder solenoid, perform zero point calibration and store the system information (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


HINT:

When DTC C1251, C1253 or C1254 is output together with DTC C1256 inspect and repair the trouble area indicated by DTC C1251, C1253 or C1254 first.


PROCEDURE

1.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Depress the brake pedal 20 times or more.


d.

Turn the ignition switch to ON.


e.

Wait for 99 seconds.


f.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is output A
DTC is not output B

HINT:

Excessive brake pedal operation results in abnormal accumulator pressure consumption. This is normal.




A

2.INSPECT HYDRAULIC BRAKE BOOSTER ASSEMBLY FUNCTION

B

2.INSPECT HYDRAULIC BRAKE BOOSTER ASSEMBLY FUNCTION
a.

Inspect brake booster pump power supply system function.

i.

Turn the ignition switch off.


ii.

Depress the brake pedal 20 times or more to release the pressure in the accumulator.

HINT:

When the pressure is released, the brake pedal stroke becomes longer.



iii.

Check that the brake fluid level is at the MAX level.


iv.

Chock the 4 wheels and release the parking brake.


v.

Turn the ignition switch to ON and measure the brake booster pump operating time (the time from when the brake booster pump starts operating until it stops).

OK:

20 to 80 seconds



vi.

Start the engine after the brake boost pump stops.


vii.

Check that the ABS warning light and slip indicator light are not illuminated.


viii.

Turn off the engine, and then turn the ignition switch to ON.


ix.

Check that the brake boost pump operates and then stops when the brake pedal is depressed 4 or 5 times.


x.

Depress the brake pedal 4 or 5 times and measure the brake booster pump operating time (the time from when the brake booster pump starts operating until it stops).

OK:

2 to 11 seconds



xi.

Check that the brake warning light illuminates and the buzzer sounds when the brake pedal is fully depressed continuously 15 to 20 times.

NOTICE:

Wait 120 seconds or more after turning the ignition switch to ON before performing this inspection.




b.

Check brake booster operation.

i.

Turn the ignition switch off.


ii.

Depress the brake pedal 20 times or more to release the pressure in the accumulator.

HINT:

When the pressure is released, the brake pedal stroke becomes longer.



iii.

Depress the brake pedal, start the engine, and check the change in the brake pedal height.

OK:

The brake pedal moves slightly inward.






OK

3.READ VALUE USING GTS (ACCUMULATOR SENSOR)

NG

5.INSPECT BRAKE BOOSTER PUMP ASSEMBLY
3.READ VALUE USING GTS (ACCUMULATOR SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Accumulator Sensor Accumulator pressure sensor reading/ Min.: 0.00 V, Max.: 5.00 V 3.58 to 5 V If the value is constant regardless of the pump operation, an accumulator pressure sensor malfunction is suspected.

e.

Check that the accumulator output value is normal.

OK:

Accumulator pressure sensor value is normal.


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

4.RECONFIRM DTC

B

C

4.RECONFIRM DTC

b.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output (for LHD) B
DTC is output (for RHD) C



A

B

C

5.INSPECT BRAKE BOOSTER PUMP ASSEMBLY
a.

b.

Using a screwdriver, remove the 2 screws and pull out the wire harness from the master cylinder solenoid.


c.
C173363E11
1.542,1.417 0.896,0.75 0.896,0.75 0.719,0.75 true 1.385,1.448 0.885,1.76 0.885,1.76 0.719,1.76 false 1.594,1.802 2.104,0.833 2.104,0.833 2.292,0.833 false 0.479,0.646 0.698,0.833 0.219,0.188 10 false *a 0.49,1.667 0.688,1.875 0.198,0.208 10 false *b 2.344,0.75 2.583,0.927 0.24,0.177 10 false *1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Red wire terminal - Black wire terminal Always Below 2 Ω


Text in Illustration
*1 Pump motor wire harness
*a Red wire
*b Black wire


d.

Install the pump motor wire harness to the master cylinder solenoid with the 2 screws (for LHD: See page Brake>BRAKE SYSTEM (OTHER)>HYDRAULIC BRAKE BOOSTER(for LHD)>REASSEMBLY, for RHD: See page Brake>BRAKE SYSTEM (OTHER)>HYDRAULIC BRAKE BOOSTER(for RHD)>REASSEMBLY).


Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG (for LHD) C
NG (for RHD) D


A

REPLACE HYDRAULIC BRAKE BOOSTER ASSEMBLY

B

REPLACE HYDRAULIC BRAKE BOOSTER ASSEMBLY

C

REPLACE BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY

D

REPLACE BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY