Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2014.08–2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255416 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1425  Open in Stop Light Switch Circuit  


DESCRIPTION

The skid control ECU (master cylinder solenoid) has an open detection circuit, which stores this DTC when detecting an open in the stop light switch input line or the ground line of the stop light switch circuit with the stop light switch off (brake pedal not depressed).

DTC Code DTC Detection Condition Trouble Area
C1425 When the IG1 terminal voltage is between 9.5 and 17.4 V, an open in the STP terminal circuit continues for 3 seconds or more.
·

Stop light switch circuit

·

Stop light control relay assembly

·

Stop light control relay circuit

·

Skid control ECU (Master cylinder solenoid)



WIRING DIAGRAM

C246896E13
5.604,0.594 6.198,0.781 0.594,0.188 10 false STP 5.396,0.583 5.563,0.75 0.167,0.167 10 false 7 5.719,1.896 6.802,2.25 1.083,0.354 10 false Open Detection Circuit 5.396,2.646 5.719,2.813 0.323,0.167 10 false A24 5.385,2.865 7.083,3.24 1.698,0.375 10 false Skid Control ECU (Master Cylinder Solenoid) 0.583,1.469 1.396,1.698 0.813,0.229 10 false from Battery 0.198,0.719 2.302,0.969 2.104,0.25 10 false from Stop Light Switch Assembly 3.552,1.469 3.813,1.635 0.26,0.167 10 false +B 3.667,1.26 3.99,1.427 0.323,0.167 10 false STP 3.656,2.177 4.031,2.365 0.375,0.188 10 false GND 3.854,1.01 4.01,1.198 0.156,0.188 10 false 2 3.313,1.385 3.458,1.573 0.146,0.188 10 false 6 3.646,2.51 3.792,2.698 0.146,0.188 10 false 4 3.542,1.896 3.917,2.083 0.375,0.188 10 false OUT 3.313,1.802 3.458,1.99 0.146,0.188 10 false 8 1.396,1.906 2.271,2.177 0.875,0.271 10 false to Stop Light 4.281,1.292 4.594,1.448 0.313,0.156 10 false A39 4.26,1.542 5.323,2.125 1.063,0.583 10 false Stop Light Control Relay Assembly

CAUTION / NOTICE / HINT

NOTICE:

After replacing the master cylinder solenoid, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CALIBRATION).


PROCEDURE

1.READ VALUE USING GTS (STOP LIGHT SW)

OK

2.RECONFIRM DTC

NG

3.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
2.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Depress the brake pedal several times to test the stop light circuit.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output (for LHD) B
DTC is output (for RHD) C



A

B

C

3.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (master cylinder solenoid) connector.


c.
U156220E02
1.688,1.125 2.458,0.667 true 0.281,0.698 0.552,0.865 0.271,0.167 10 false A24 0.167,0.083 0.469,0.344 0.302,0.26 10 false *a 2.51,0.563 2.865,0.75 0.354,0.188 10 false STP

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-7 (STP) - Body ground Brake pedal depressed 8 to 14 V
Brake pedal released Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid])



OK

4.CHECK HARNESS AND CONNECTOR (+B/GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (+B/GND TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the stop light control relay assembly connector.


c.
U156208E03
1.083,1.479 0.271,1.625 0.271,1.625 0.271,1.708 false 1.76,1.448 2.729,0.688 2.729,0.688 2.823,0.688 false 0.125,0.135 0.354,0.417 0.229,0.281 10 false *a 1.625,0.26 1.917,0.479 0.292,0.219 10 false A39 2.917,0.583 3.156,0.75 0.24,0.167 10 false +B 0.115,1.781 0.479,1.958 0.365,0.177 10 false GND

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-6 (+B) - Body ground Always 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A39-4 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Control Relay Assembly)



OK

5.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the stop light control relay assembly connector.


c.
U164959E02
1.375,1.198 0.281,1.625 0.281,1.625 0.281,1.708 false 0.094,0.125 0.313,0.365 0.219,0.24 10 false *a 1.615,0.25 1.938,0.448 0.323,0.198 10 false A39 0.146,1.76 0.51,1.938 0.365,0.177 10 false STP

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-2 (STP) - Body ground Brake pedal depressed 8 to 14 V
Brake pedal released Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Control Relay Assembly)



OK

6.CHECK HARNESS AND CONNECTOR (OUT TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (OUT TERMINAL)
a.

Reconnect the stop light control relay assembly connector.


b.
U156646E01
0.126,0.079 2.449,0.422 2.323,0.343 10 *a 0.227,2.027 0.555,2.195 0.328,0.168 10 OUT 2.803,1.945 3.093,2.113 0.290,0.168 10 A39 1.169,2.111 0.625,2.111 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-8 (OUT) - Body ground Brake pedal depressed 8 to 14 V
Brake pedal released Below 1.5 V


Text in Illustration
*a Component with harness connected
(Stop Light Control Relay Assembly)



OK

7.RECONFIRM DTC

NG

REPLACE STOP LIGHT CONTROL RELAY ASSEMBLY

7.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Depress the brake pedal several times to test the stop light circuit.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output (for LHD) B
DTC is output (for RHD) C



A

B

C