Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2014.08–2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255416 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1422  Master Cylinder Pressure Sensor Zero Point High Malfunction  


DESCRIPTION

Refer to DTCs C1421, C1423 and C1424 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C1281).

DTC Code DTC Detection Condition Trouble Area
C1422 When the stop light switch is off, the PM/C1 terminal voltage is 0.86 V or higher for 5 seconds or more.
·

STOP fuse

·

Stop light switch assembly

·

Stop light switch circuit

·

Master cylinder pressure sensor circuit

·

Master cylinder solenoid (Master cylinder pressure sensor)



WIRING DIAGRAM

C262553E03
4.813,2.604 5.146,2.792 0.333,0.188 10 false A24 4.813,2.823 6.563,3.188 1.75,0.365 10 false Skid Control ECU (Master Cylinder Solenoid) 4.948,1.552 5.333,1.75 0.385,0.198 10 false STP 4.656,1.396 4.833,1.594 0.177,0.198 10 false 7 1.594,1.865 1.927,2.052 0.333,0.188 10 false A30 1.583,2.073 3.396,2.281 1.813,0.208 10 false Stop Light Switch Assembly 1.781,1.427 1.938,1.615 0.156,0.188 10 false 2 2.99,1.427 3.146,1.615 0.156,0.188 10 false 1 1.469,0.573 1.969,0.802 0.5,0.229 10 false STOP 2.708,0.375 3.542,0.594 0.833,0.219 10 false from Battery

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the master cylinder solenoid, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.READ VALUE USING GTS (STOP LIGHT SW)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-


f.

Check that the stop light switch condition observed on the GTS changes according to brake pedal operation.

OK:

The GTS displays ON and OFF according to brake pedal operation.




OK

2.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION

NG

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH POWER SOURCE TERMINAL)
2.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION
a.

Turn the ignition switch off.


b.

Check the brake pedal height and stop light switch installation (for LHD: See page Brake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for LHD)>ADJUSTMENT, for RHD: See page Brake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for RHD)>ADJUSTMENT).

OK:

The brake pedal height and stop light switch installation are normal.




OK

3.RECONFIRM DTC

NG

ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH

3.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more and perform a braking test (decelerate the vehicle by depressing the brake pedal).


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output (for LHD) B
DTC is output (for RHD) C



A

B

C

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH POWER SOURCE TERMINAL)
a.

Make sure that there is no looseness in the locking part and connecting part of the connectors.


b.

Disconnect the stop light switch assembly connector.


c.
U164985E01
0.232,0.198 0.482,0.479 0.250,0.281 10 *a 0.652,1.25 0.926,1.413 0.274,0.163 10 A30

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A30-2 - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)



OK

5.INSPECT STOP LIGHT SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT STOP LIGHT SWITCH
a.

Remove the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL).


b.
C215187E01
0.266,0.116 0.476,0.290 0.209,0.174 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Switch pin not pushed in Below 1 Ω
Switch pin pushed in 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Stop Light Switch Assembly)



OK

6.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (master cylinder solenoid) connector.


c.
U156220E02
1.688,1.125 2.458,0.667 true 0.281,0.698 0.552,0.865 0.271,0.167 10 false A24 0.167,0.083 0.469,0.344 0.302,0.26 10 false *a 2.51,0.563 2.865,0.75 0.354,0.188 10 false STP

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A24-7 (STP) - Body ground Brake pedal depressed 8 to 14 V
Brake pedal released Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid])

Result
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C