Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › from 2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255416 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1425  Open in Stop Light Switch Circuit  


DESCRIPTION

The skid control ECU (master cylinder solenoid) has an open detection circuit, which stores this DTC when detecting an open in the stop light switch input line or the ground line of the stop light switch circuit with the stop light switch off (brake pedal not depressed).

DTC Code DTC Detection Condition Trouble Area
C1425 When the IG1 terminal voltage is 9.5 V or more, the skid control ECU detects an open in the STP circuit for 3 seconds or more.
·

Harness or connector

·

Stop light switch assembly

·

Stop light control relay assembly

·

Skid control ECU (Master cylinder solenoid)



WIRING DIAGRAM

C219164E18
5.604,0.594 6.198,0.781 0.594,0.188 10 false STP 5.396,0.583 5.563,0.75 0.167,0.167 10 false 7 5.719,1.896 6.802,2.25 1.083,0.354 10 false Open Detection Circuit 5.396,2.646 5.719,2.813 0.323,0.167 10 false A24 5.385,2.865 7.083,3.24 1.698,0.375 10 false Skid Control ECU (Master Cylinder Solenoid) 1.844,2.021 2.656,2.25 0.813,0.229 10 false from Battery 1.76,0.615 2.021,0.781 0.26,0.167 10 false B 3.667,1.26 4.021,1.427 0.354,0.167 10 false STP 3.854,1.01 4.01,1.198 0.156,0.188 10 false 2 3.656,1.969 3.802,2.156 0.146,0.188 10 false 4 4.208,1.281 4.521,1.438 0.313,0.156 10 false A39 4.198,1.479 5.26,2.063 1.063,0.583 10 false Stop Light Control Relay Assembly 3.646,1.708 4.104,1.865 0.458,0.156 10 false GND 2.531,0.615 2.792,0.781 0.26,0.167 10 false L 0.781,2.177 1.302,2.375 0.521,0.198 10 false STOP 2.729,0.615 2.885,0.802 0.156,0.188 10 false 2 1.552,0.615 1.708,0.802 0.156,0.188 10 false 1 1.677,1.031 2.135,1.229 0.458,0.198 10 false A73 1.667,1.208 2.771,1.667 1.104,0.458 10 false Stop Light Switch Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the master cylinder solenoid, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed.

Result:
Result Proceed to
All stop lights illuminate when the brake pedal is depressed. A
All stop lights do not illuminate when the brake pedal is depressed. B




A

2.READ VALUE USING GTS (STOP LIGHT SW)

B

6.INSPECT STOP LIGHT SWITCH ASSEMBLY
2.READ VALUE USING GTS (STOP LIGHT SW)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-


f.

Check the value of Stop Light SW when the brake pedal is depressed.

Result:
Result Proceed to
The value of Stop Light SW is ON A
Other than above B




A

3.CHECK FOR SHORT TO +B IN STP CIRCUIT

B

5.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
3.CHECK FOR SHORT TO +B IN STP CIRCUIT
a.

Check that there is no short to +B in the STP circuit (wire harnesses and connectors).

OK:

No short to +B




OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE MALFUNCTIONING PART

4.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Perform a road test.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output (for LHD) B
DTC is output (for RHD) C



A

B

C

5.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (master cylinder solenoid) connector.


c.
U156220E02
1.688,1.125 2.458,0.667 true 0.281,0.698 0.552,0.865 0.271,0.167 10 false A24 0.167,0.083 0.469,0.344 0.302,0.26 10 false *a 2.51,0.563 2.865,0.75 0.354,0.188 10 false STP

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-7 (STP) - Body ground Brake pedal depressed 8 to 14 V
Brake pedal released Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid])

Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C




A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly (See pageVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION).

OK:

The stop light switch assembly is normal.




OK

7.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.

Turn the engine switch off.


b.

Disconnect the skid control ECU (master cylinder solenoid) connector.


c.
U156220E01
0.26,0.712 0.534,0.874 0.274,0.163 10 A24 0.128,0.038 2.553,0.393 2.426,0.354 10 *a 2.509,0.565 2.859,0.742 0.350,0.177 10 STP 1.684,1.133 2.457,0.677 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-7 (STP) - Body ground Brake pedal depressed 8 to 14 V
Brake pedal released Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid])



OK

8.CHECK STOP LIGHT CONTROL RELAY (STP TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK STOP LIGHT CONTROL RELAY (STP TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the stop light control relay assembly connector.


c.
U164960E05
1.417,1.104 0.917,0.667 0.917,0.667 0.75,0.667 false 0.083,0.094 0.271,0.271 0.188,0.177 10 false *a 1.625,0.25 1.917,0.458 0.292,0.208 10 false A39 0.417,0.604 0.781,0.781 0.365,0.177 10 false STP

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A39-2 (STP) - Body ground Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Control Relay Assembly)



OK

REPLACE STOP LIGHT CONTROL RELAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR