Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › from 2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255416 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1252  Brake Booster Pump Motor on Time Abnormally Long  


DESCRIPTION

The motor relay (semiconductor relay) is built into the master cylinder solenoid and drives the pump motor based on a signal from the skid control ECU (master cylinder solenoid).

DTC Code DTC Detection Condition Trouble Area
C1252 The motor operates for 3 minutes or more.
·

Brake booster with accumulator pump assembly

·

Pump motor wire harness condition

·

Skid control ECU (Master cylinder solenoid)

·

Hydraulic brake booster assembly



HINT:

The pump motor continues operation for the first 3 minutes, and then starts and stops repeatedly.


CAUTION / NOTICE / HINT

NOTICE:

After replacing the master cylinder solenoid, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CALIBRATION).


HINT:

When DTC C1253, C1254, C1256 or C1452 is output together with DTC C1252, inspect and repair the trouble area indicated by DTC C1253, C1254, C1256 or C1452 first.


PROCEDURE

1.CHECK PUMP MOTOR OPERATION
a.

Turn the ignition switch off.


b.

Depress the brake pedal more than 40 times.


c.

Turn the ignition switch to ON.


d.

Check how the pump motor operates.

Result
Result Proceed to
Pump motor does not operate A
Pump motor operates continuously and does not stop B
Pump motor operates intermittently C
Pump motor operates, and then stops D


HINT:

Refer to the hydraulic brake booster assembly installation procedures:




A

2.CHECK CONNECTION OF PUMP MOTOR WIRE HARNESS

B

REPLACE HYDRAULIC BRAKE BOOSTER ASSEMBLY

C

4.READ VALUE USING GTS (ACCUMULATOR SENSOR)

D

5.RECONFIRM DTC
2.CHECK CONNECTION OF PUMP MOTOR WIRE HARNESS

OK

3.CHECK RESISTANCE OF PUMP MOTOR WIRE HARNESS

NG

RETIGHTEN SCREWS

3.CHECK RESISTANCE OF PUMP MOTOR WIRE HARNESS

OK

4.READ VALUE USING GTS (ACCUMULATOR SENSOR)

NG

REPLACE BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY

4.READ VALUE USING GTS (ACCUMULATOR SENSOR)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Accumulator Sensor Accumulator pressure sensor reading/ Min.: 0.00 V, Max.: 5.00 V 3.58 to 5 V If the value is constant regardless of the pump operation, an accumulator pressure sensor malfunction is suspected.


f.

Check the accumulator output value.

Result
Result Proceed to
Output value is within "Normal Condition" range A
Output value is out of "Normal Condition" range B
Output value is constant regardless of pump operation C


HINT:
·

Refer to the hydraulic brake booster assembly installation procedures:

for LHD (See page Brake>BRAKE SYSTEM (OTHER)>HYDRAULIC BRAKE BOOSTER(for LHD)>REMOVAL)

for RHD (See page Brake>BRAKE SYSTEM (OTHER)>HYDRAULIC BRAKE BOOSTER(for RHD)>REMOVAL)

·

Refer to the master cylinder solenoid installation procedures:

for LHD (See page Brake>BRAKE SYSTEM (OTHER)>HYDRAULIC BRAKE BOOSTER(for LHD)>DISASSEMBLY)

for RHD (See page Brake>BRAKE SYSTEM (OTHER)>HYDRAULIC BRAKE BOOSTER(for RHD)>DISASSEMBLY)




A

5.RECONFIRM DTC

B

REPLACE MASTER CYLINDER SOLENOID

C

REPLACE HYDRAULIC BRAKE BOOSTER ASSEMBLY

5.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON.


d.

Wait for more than 5 minutes.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is output A
DTC is not output B

HINT:
·

Reinstall the sensors, reconnect the connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.

·

Refer to the hydraulic brake booster assembly installation procedures:

for LHD (See page Brake>BRAKE SYSTEM (OTHER)>HYDRAULIC BRAKE BOOSTER(for LHD)>REMOVAL)

for RHD (See page Brake>BRAKE SYSTEM (OTHER)>HYDRAULIC BRAKE BOOSTER(for RHD)>REMOVAL)

·

Refer to the brake booster with accumulator pump assembly installation procedures:

for LHD (See page Brake>BRAKE SYSTEM (OTHER)>HYDRAULIC BRAKE BOOSTER(for LHD)>DISASSEMBLY)

for RHD (See page Brake>BRAKE SYSTEM (OTHER)>HYDRAULIC BRAKE BOOSTER(for RHD)>DISASSEMBLY)





A

REPLACE HYDRAULIC BRAKE BOOSTER ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY