Home › Vehicle Interior › INTERIOR PANELS / TRIM › INSTRUMENT PANEL SAFETY PAD › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052849 INTERIOR PANELS / TRIM _0255717 INSTRUMENT PANEL SAFETY PAD A

INTERIOR PANELS / TRIM  INSTRUMENT PANEL SAFETY PAD  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. TABLE OF BOLT, SCREW AND NUT

HINT:

All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet code in the table below.


B292999E01
0.167,0.125 0.542,0.292 0.375,0.167 10 false Code 1.208,0.115 1.646,0.281 0.438,0.167 10 false Shape 2.49,0.115 2.865,0.281 0.375,0.167 10 false Code 3.552,0.115 3.99,0.281 0.438,0.167 10 false Shape 4.802,0.115 5.177,0.281 0.375,0.167 10 false Code 5.844,0.115 6.281,0.281 0.438,0.167 10 false Shape 0.198,0.771 0.49,0.927 0.292,0.156 10 false <A> 0.208,1.688 0.5,1.844 0.292,0.156 10 false <D> 2.531,0.792 2.823,0.948 0.292,0.156 10 false <B> 2.531,1.698 2.823,1.854 0.292,0.156 10 false <E> 4.833,0.802 5.125,0.958 0.292,0.156 10 false <C> 1.854,0.479 2.094,0.656 0.24,0.177 10 false φ 6 1.844,0.677 2.313,0.854 0.469,0.177 10 false (0.236) 1.854,0.927 2.208,1.083 0.354,0.156 10 false L=16 1.844,1.104 2.323,1.292 0.479,0.188 10 false (0.630) 6.375,1.396 6.615,1.573 0.24,0.177 10 false φ 5 6.354,1.573 6.823,1.75 0.469,0.177 10 false (0.197) 6.375,1.833 6.729,1.99 0.354,0.156 10 false L=18 6.354,1.979 6.833,2.167 0.479,0.188 10 false (0.709) 4.115,0.51 4.354,0.688 0.24,0.177 10 false φ 5 4.104,0.688 4.573,0.865 0.469,0.177 10 false (0.197) 4.115,0.927 4.469,1.083 0.354,0.156 10 false L=15 4.104,1.104 4.583,1.292 0.479,0.188 10 false (0.590) 6.208,0.698 6.448,0.875 0.24,0.177 10 false φ 6 6.188,0.885 6.656,1.063 0.469,0.177 10 false (0.236) 4.76,2.354 6.094,2.542 1.333,0.188 10 false mm (in.) (L = Length) 4.833,1.719 5.125,1.875 0.292,0.156 10 false <F> 1.844,1.406 2.083,1.583 0.24,0.177 10 false φ 8 1.823,1.583 2.292,1.76 0.469,0.177 10 false (0.315) 1.844,1.823 2.198,1.979 0.354,0.156 10 false L=20 1.823,1.99 2.302,2.177 0.479,0.188 10 false (0.787) 4.115,1.417 4.354,1.594 0.24,0.177 10 false φ 6 4.104,1.594 4.573,1.771 0.469,0.177 10 false (0.236) 4.115,1.833 4.469,1.99 0.354,0.156 10 false L=21 4.104,2.01 4.583,2.198 0.479,0.188 10 false (0.826)

Hide 2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM (w/ Cool Box)

Hide 3. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

a.

for Power Tilt and Power Telescopic Steering Column:

i.

Disable the Autoaway/Return function by changing the customize parameter (See page General>INTRODUCTION>REPAIR INSTRUCTION>CUSTOMIZE PARAMETERS).

NOTICE:

Record the current customize parameter setting (whether the Autoaway/Return function is enabled or disabled) in order to restore the current setting after finishing the operation.


HINT:

Performing the above operation causes the Autoaway/Return function to be disabled when the engine switch is turned off.



ii.

Turn the engine switch on (IG). Operate the tilt and telescopic switch to fully extend and lower the steering column.



b.

Turn the engine switch off and disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



Hide 45187 5.REMOVE LOWER NO. 3 STEERING WHEEL COVER

Hide 45186 6.REMOVE LOWER NO. 2 STEERING WHEEL COVER

Hide 45100 8.REMOVE STEERING WHEEL ASSEMBLY

Hide 9.REMOVE LOWER STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column)

Hide 10.REMOVE LOWER STEERING COLUMN COVER (for Manual Tilt and Manual Telescopic Steering Column)

Hide 45286B 11.REMOVE UPPER STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column)

Hide 45286B 12.REMOVE UPPER STEERING COLUMN COVER (for Manual Tilt and Manual Telescopic Steering Column)

Hide 89235A 13.REMOVE TILT AND TELESCOPIC SWITCH (for Power Tilt and Power Telescopic Steering Column)

Hide 84140 14.REMOVE COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)

Hide 84140 15.REMOVE COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)

Hide 71200S 16.REMOVE FRONT SEAT ASSEMBLY LH (for Power Seat)

Hide 71200S 17.REMOVE FRONT SEAT ASSEMBLY LH (for Manual Seat)

Hide 71100S 18.REMOVE FRONT SEAT ASSEMBLY RH (for Power Seat)

Hide 71100S 19.REMOVE FRONT SEAT ASSEMBLY RH (for Manual Seat)

Hide 20.REMOVE FRONT SEAT ASSEMBLY RH (for Bench Seat Type)

Hide 58901A 21.REMOVE REAR CONSOLE BOX SUB-ASSEMBLY (w/o Cool Box)

Hide 88520 22.REMOVE COOLING BOX ASSEMBLY (w/ Cool Box)

Hide 58812A 23.REMOVE LOWER CONSOLE BOX (w/o Console Box Lid)

Hide 55318C 24.REMOVE INSTRUMENT SIDE PANEL LH

E154740E06
2.594,0.749 2.852,0.958 0.258,0.209 10 *1 2.024,0.87 2.591,0.846 false

a.

Place protective tape as shown in the illustration.

Text in Illustration
*1 Protective Tape


b.

Using a moulding remover, detach the 6 claws and remove the instrument side panel.


Hide 55474C 25.REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

E154744E04
1.095,1.818 1.273,2.018 0.177,0.200 10 *1 1.19,1.806 1.116,1.359 false

a.

Place protective tape as shown in the illustration.

Text in Illustration
*1 Protective Tape


b.

Using a moulding remover, detach the 3 claws and remove the No. 1 instrument cluster finish panel garnish.


Hide 55475A 26.REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH

a.

Place protective tape as shown in the illustration.


b.

Using a moulding remover, detach the 2 claws and remove the No. 2 instrument cluster finish panel garnish.

B291251E02
1.094,1.344 0.49,1.104 false 4.646,1.583 4.063,1.354 false 3.833,0.156 4.125,0.49 0.292,0.333 10 false *B 0.365,0.156 0.656,0.49 0.292,0.333 10 false *A 0.344,1.01 0.635,1.344 0.292,0.333 10 false *1 3.917,1.26 4.208,1.594 0.292,0.333 10 false *1

Text in Illustration
*A w/ Entry and Start System *B w/o Entry and Start System
*1 Protective Tape - -


Hide 55404C 27.REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/ Multi-information Display)

B180017

a.

Detach the 9 claws.


b.

Disconnect the connector and remove the instrument cluster finish panel.


Hide 55404C 28.REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Multi-information Display)

B180016

a.

Detach the 9 claws and remove the instrument cluster finish panel.


Hide 83100 29.REMOVE COMBINATION METER ASSEMBLY (w/ Multi-information Display)

B180019

a.

Remove the 4 screws.


b.

Disconnect the connectors and remove the combination meter.


Hide 83100 30.REMOVE COMBINATION METER ASSEMBLY (w/o Multi-information Display)

B180018

a.

Remove the 4 screws.


b.

Disconnect the connectors and remove the combination meter.


Hide 67914B 31.REMOVE FRONT DOOR SCUFF PLATE LH (w/o Sliding Roof)

Hide 67914B 32.REMOVE FRONT DOOR SCUFF PLATE LH (w/ Sliding Roof)

Hide 55606 33.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

B180655

a.

Remove the 2 screws.


b.

Detach the 3 claws.


c.

Disconnect the connectors and remove the No. 1 instrument panel under cover.


Hide 62112 34.REMOVE COWL SIDE TRIM BOARD LH

B181911

a.

Remove the cap nut.


b.

Detach the 2 clips and remove the cowl side trim board.


Hide 55432D 35.REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

U163955E01
2.087,1.553 2.274,1.741 0.187,0.187 10 *1 2.068,1.611 1.418,1.306 false

a.

Using a screwdriver, detach the 2 claws and open the hole cover.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
*1 Protective Tape


b.

w/ Driver Side Knee Airbag:

i.

Remove the 2 bolts.


ii.

Detach the 16 claws.

B291249



c.

w/o Driver Side Knee Airbag:

i.

Remove the 2 bolts.


ii.

Detach the 9 claws.

B291250



d.
B180296

for Automatic Air Conditioning System:

i.

Detach the 2 claws and remove the room temperature sensor.



e.
B181942

Detach the 2 claws and disconnect the 2 control cables.


f.

Disconnect the connectors and remove the lower No. 1 instrument panel finish panel.


Hide 55446A 36.REMOVE NO. 1 SWITCH HOLE BASE

B180298

a.

Detach the 4 claws.


b.

Disconnect the connectors and remove the No. 1 switch hole cover.


Hide 73900 37.REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

Hide 55303B 38.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

B180299

a.

Detach the 2 claws and disconnect the DLC3.


b.

Remove the 5 bolts and lower instrument panel.


Hide 55650 39.REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

B180300

a.

Detach the 4 claws and remove the No. 1 instrument panel register.


Hide 55317A 40.REMOVE INSTRUMENT SIDE PANEL RH (w/o Airbag Cut Off Switch)

B181912E02
1.101,0.223 1.294,0.458 0.192,0.235 10 *1 1.627,1.233 1.242,0.4 false

a.

Place protective tape as shown in the illustration.

Text in Illustration
*1 Protective Tape


b.

Using a moulding remover, detach the 6 claws and remove the instrument side panel.


Hide 55317A 41.REMOVE INSTRUMENT SIDE PANEL RH (w/ Airbag Cut Off Switch)

B180301E02
1.097,0.16 1.305,0.342 0.208,0.182 10 *1 1.644,1.22 1.245,0.347 false

a.

Place protective tape as shown in the illustration.

Text in Illustration
*1 Protective Tape


b.

Using a moulding remover, detach the 6 claws.


c.

Disconnect the connector and remove the instrument side panel.


Hide 67913B 42.REMOVE FRONT DOOR SCUFF PLATE RH (w/o Sliding Roof)

Hide 67913B 43.REMOVE FRONT DOOR SCUFF PLATE RH (w/ Sliding Roof)

Hide 55607 44.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

B180656

a.

Detach the 4 claws and remove the No. 2 instrument panel under cover.


Hide 62111C 45.REMOVE COWL SIDE TRIM BOARD RH

B180022

a.

Remove the cap nut.


b.

Detach the 2 clips and remove the cowl side trim board.


Hide 73990 46.REMOVE FRONT PASSENGER SIDE KNEE AIRBAG ASSEMBLY (w/ Passenger Side Knee Airbag)

Hide 55312 47.REMOVE LOWER INSTRUMENT PANEL (w/o Passenger Side Knee Airbag)

B180302

a.

Remove the 2 bolts.


b.

Detach the 4 claws and remove the lower instrument panel.


Hide 55476A 48.REMOVE NO. 3 INSTRUMENT CLUSTER FINISH PANEL GARNISH

B180303E02
1.16,0.485 1.380,0.705 0.220,0.220 10 *1 1.515,1.7 1.302,0.663 false

a.

Place protective tape as shown in the illustration.

Text in Illustration
*1 Protective Tape


b.

Using a moulding remover, detach the 6 claws and remove the No. 3 instrument cluster finish panel garnish.


Hide 55443D 49.REMOVE INSTRUMENT PANEL BOX DOOR KNOB

B182302

a.

Using a moulding remover, detach the 2 claws and remove the instrument panel box door knob.


Hide 55433B 50.REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

B180304

a.

Remove the 4 bolts.


b.

Detach the 3 claws.


c.

Disconnect the connector and remove the lower No. 2 instrument panel finish panel.


Hide 55660 51.REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY

B180305

a.

Detach the 4 claws and remove the No. 2 instrument panel register.


Hide 74610A 52.REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY (w/o Sliding Roof)

Hide 74610A 53.REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY (w/ Sliding Roof)

Hide 62212 54.REMOVE FRONT PILLAR GARNISH LH (w/o Sliding Roof)

Hide 62212 55.REMOVE FRONT PILLAR GARNISH LH (w/ Sliding Roof)

Hide 62211 56.REMOVE FRONT PILLAR GARNISH RH (w/o Sliding Roof)

Hide 62211 57.REMOVE FRONT PILLAR GARNISH RH (w/ Sliding Roof)

Hide 55510F 58.REMOVE NO. 1 SPEAKER OPENING COVER ASSEMBLY

Hide 55408F 60.REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

Hide 86160P 61.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (LH Side)

Hide 55409F 62.REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

Hide 86160P 63.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (RH Side)

Hide 55670 64.REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY

B180307E03
1.563,2.625 1.875,2.917 true 1.823,2.938 2.021,3.156 0.198,0.219 10 false *1

a.

Place protective tape as shown in the illustration.

Text in Illustration
*1 Protective Tape


b.

Using a moulding remover, detach the 6 claws.


c.

Disconnect the connector and remove the No. 3 instrument panel register.


Hide 55680A 65.REMOVE NO. 4 INSTRUMENT PANEL REGISTER ASSEMBLY

B181944E03
1.802,2.677 2.198,2.938 true 2.198,2.948 2.396,3.177 0.198,0.229 10 false *1

a.

Place protective tape as shown in the illustration.

Text in Illustration
*1 Protective Tape


b.

Using a moulding remover, detach the 6 claws.


c.

Disconnect the connector and remove the No. 4 instrument panel register.


Hide 86111 66.REMOVE MULTI-DISPLAY ASSEMBLY WITH BRACKET (w/ Multi-display)

Hide 86120 67.REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/o Multi-display)

Hide 55412C 68.REMOVE NO. 1 CENTER INSTRUMENT CLUSTER FINISH PANEL

B180653

a.

Detach the 10 claws.


b.

Disconnect the connector and remove the No. 1 center instrument cluster finish panel.


Hide 86120 69.REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ Cassette Tape Player)

Hide 55522B 70.REMOVE RADIO TUNER OPENING COVER WITH BRACKET (w/o Radio Receiver)

B180654

a.

Remove the 2 bolts.


b.

Remove the 2 screws and radio tuner opening cover with bracket.


Hide 71.REMOVE MULTI-MEDIA MODULE RECEIVER ASSEMBLY WITH BRACKET (w/ Multi-display)

Hide 87212F 73.REMOVE REAR NO. 2 AIR DUCT (w/ Rear Air Duct)

B180308

a.

Fold back the front floor carpet.


b.

Detach the clip and remove the rear No. 2 air duct.


Hide 87212H 74.REMOVE REAR NO. 4 AIR DUCT (w/ Rear Air Duct)

B180309

a.

Fold back the front floor carpet.


b.

Detach the clip and remove the rear No. 4 air duct.


Hide 55400 75.REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY (for LHD)

a.

Disconnect the connectors.

B182523E01
1.076,1.537 2.400,1.952 1.324,0.416 12 w/ Parking Assist Monitor System: 3.204,1.537 6.404,1.948 3.200,0.411 12 w/ TOYOTA Parking Assist-Sensor System and w/o Parking Assist Monitor System:


b.

Disconnect the connectors and detach the clamps.


c.

Remove the bolt and disconnect the wire harness.

B180532


d.

Remove the 2 passenger airbag bolts.


e.

Disconnect the connectors.


f.

Remove the 8 bolts.


g.

Remove the 2 nuts and instrument panel safety pad.

B180534


Hide 55400 76.REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY (for RHD)

a.

Disconnect the connectors.

B187975E01
1.362,1.549 2.685,1.965 1.324,0.416 12 w/ Parking Assist Monitor System: 3.247,1.549 6.447,1.960 3.200,0.411 12 w/ TOYOTA Parking Assist-Sensor System and w/o Parking Assist Monitor System:


b.

Disconnect the connectors and detach the clamps.


c.

Remove the bolt and disconnect the wire harness.

B180533


d.

Remove the 2 passenger airbag bolts.


e.

Disconnect the connectors.


f.

Remove the 8 bolts.


g.

Remove the 2 nuts and instrument panel safety pad.

B180535