Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM(w/ Variable Flow Control Solenoid Valve) › from 2015.08
RM2660E _55 Steering _052824 POWER ASSIST SYSTEMS _0255447 POWER STEERING SYSTEM(w/ Variable Flow Control Solenoid Valve) C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM(w/ Variable Flow Control Solenoid Valve)  C15F0  VFC Solenoid Circuit  


DESCRIPTION

This circuit supplies electric power to the variable flow control solenoid valve.

The power steering ECU controls the output current to the variable flow control solenoid valve in accordance with the steering angle signal, VGRS relative angle signal, steering zero point memory, vehicle speed signal and engine speed signal, adjusting the amount of power steering assist.

DTC Code DTC Detection Condition Trouble area
C15F0 A short or open in the solenoid valve circuit.
·

Harness or connector

·

Vane pump assembly

·

Power steering ECU assembly



WIRING DIAGRAM

C210556E15
5.312,2.392 6.610,2.574 1.298,0.181 10 Power Steering ECU 1.98,1.158 4.984,1.526 3.004,0.368 10 Variable Flow Control Solenoid Valve 5.504,0.735 5.887,0.917 0.384,0.181 10 SOF+ 5.504,1.702 5.852,1.883 0.349,0.181 10 SOF- 5.302,0.652 5.458,0.833 0.156,0.181 10 7 5.302,1.605 5.458,1.786 0.156,0.181 10 8 3.505,0.658 3.661,0.840 0.156,0.181 10 2 2.209,0.658 2.365,0.840 0.156,0.181 10 1 1.986,1 2.398,1.181 0.412,0.181 10 C149 5.312,2.224 5.732,2.405 0.420,0.181 10 E102 3.038,0.658 3.421,0.840 0.384,0.181 10 SOF+ 2.414,0.658 2.763,0.840 0.349,0.181 10 SOF-

PROCEDURE

1.READ VALUE USING GTS (SOLENOID CURRENT)
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / PPS / Data List.

PPS
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Solenoid Current Solenoid Current/
Min.: 0 mA
Max.: 1000 mA
200 to 950 mA The engine is running and the steering wheel is being turned.

OK:

The normal condition value is displayed on the GTS.




OK

NG

2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU - VARIABLE FLOW CONTROL SOLENOID VALVE)
2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU - VARIABLE FLOW CONTROL SOLENOID VALVE)
a.

Disconnect the E102 power steering ECU connector.


b.

Disconnect the C149 variable flow control solenoid valve connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E102-7 (SOF+) - C149-2 (SOF+) Always Below 1 Ω
E102-8 (SOF-) - C149-1 (SOF-)
E102-7 (SOF+) - Body ground Always 10 kΩ or higher
E102-8 (SOF-) - Body ground




OK

3.INSPECT VARIABLE FLOW CONTROL SOLENOID VALVE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT VARIABLE FLOW CONTROL SOLENOID VALVE
C358280E01
0.844,2.917 1.542,3.313 true 2.448,2.958 1.875,3.333 true 0.823,0.802 1.521,1.198 true 2.448,0.833 1.875,1.208 true 1.292,4.417 1.552,4.625 0.26,0.208 10 false (+) 1.99,4.406 2.219,4.615 0.229,0.208 10 false (-) 0.208,0.698 0.823,0.927 0.615,0.229 10 false 2 (SOF+) 0.24,2.823 0.854,3.052 0.615,0.229 10 false 2 (SOF+) 2.5,0.708 3.063,0.938 0.563,0.229 10 false 1 (SOF-) 2.5,2.844 3.063,3.073 0.563,0.229 10 false 1 (SOF-) 0.146,0.063 0.344,0.271 0.198,0.208 10 false *a

a.

Disconnect the C149 variable flow control solenoid valve connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SOF-) - 2 (SOF+) 20°C (68°F) 6.7 to 7.3 Ω



c.

Connect the positive (+) lead of the battery with a 21 W bulb to terminal 2 (SOF+) and the negative (-) lead to terminal 1 (SOF-) of the solenoid valve connector. Then check that the valve moves and makes an operating noise.

OK:

Valve moves and makes an operating noise.


Text in Illustration
*a Component without harness connected
(Variable Flow Control Solenoid Valve)

Result
Result Proceed to
OK A
NG for 1UR-FE B
for 3UR-FE C
for 1VD-FTV D



A

B

C

D