Home › Steering › VARIABLE GEAR RATIO STEERING › VARIABLE GEAR RATIO STEERING SYSTEM › 2014.08–2015.08
RM2660E _55 Steering _052825 VARIABLE GEAR RATIO STEERING _0255448 VARIABLE GEAR RATIO STEERING SYSTEM J

VARIABLE GEAR RATIO STEERING  VARIABLE GEAR RATIO STEERING SYSTEM  VGRS System Stops or does not Operate  


CAUTION / NOTICE / HINT

HINT:

This problem may be caused by a malfunction in the vehicle stability control system or steering system.

Make sure that no DTC is output for the skid control ECU or steering control ECU before proceeding with the following procedures.

If a DTC is output for either of these ECUs, first troubleshoot it and then proceed to the troubleshooting below.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (RECORD OF OVERHEAT)
a.

Use the Data List to check if the record of overheat is functioning properly.

VGRS
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Motor Overheat Record Record of continuous overheat preventive control/Rec or Unrec Rec or Unrec -

Result
Result Proceed to
"Rec" (Record of motor overheating) A
"Unrec" (No record of motor overheating) B

HINT:

If "Rec" is displayed, reset the setting to "Unrec". Enter the VGRS menu on the tester, select record clearance, and follow the prompts to set to "Unrec".




A

2.CHECK HEAT PROTECTION FUNCTION FOR STEERING ACTUATOR

B

3.CHECK STEERING EFFORT
2.CHECK HEAT PROTECTION FUNCTION FOR STEERING ACTUATOR
a.

Turn the engine switch on (IG) and wait for 30 minutes until the steering actuator cools down.


b.

Start the engine and slowly turn the steering wheel from lock to lock (approximately 90°/sec.) 3 times.

HINT:

If turning the steering wheel quickly while driving at low speeds, the steering angle may differ between the left and right, or the steering wheel may become off-center.

However, this is not a malfunction.



c.

Check the number of turns from lock to lock.

Result
Result Proceed to
3.2 turns A
2.7 turns B



A

3.CHECK STEERING EFFORT

B

VGRS SYSTEM IS NORMAL

3.CHECK STEERING EFFORT
a.

Start the engine.


b.

Turn the steering wheel.


c.

Measure the steering effort.

Standard steering effort:

Below 6.9 N*m (70 kgf*cm, 61 in.*lbf)


HINT:

After completing the inspection or repair, attempt to simulate the problem and then perform "Read Value Using Intelligent Tester" above again to reconfirm that the problem does not occur.


Result
Result Proceed to
OK A
NG (for 1VD-FTV with DPF) B
NG (except 1VD-FTV with DPF) C



A

4.CHECK STEERING ACTUATOR

B

GO TO POWER STEERING SYSTEM (PROBLEM SYMPTOMS TABLE)

C

GO TO POWER STEERING SYSTEM (PROBLEM SYMPTOMS TABLE)

4.CHECK STEERING ACTUATOR
a.

Check for abnormal noise or vibration in the steering actuator.

OK:

Neither abnormal noise nor vibration occurs.




OK

5.CHECK STEERING CONTROL ECU (POWER SOURCE CIRCUIT)

NG

5.CHECK STEERING CONTROL ECU (POWER SOURCE CIRCUIT)
U164527E02
1.365,1.573 1.094,1.969 false 1.51,1.552 1.938,1.948 false 1.281,1.521 0.469,1.969 false 0.115,0.083 2.604,0.479 2.49,0.396 10 false Component with harness connected: (Steering Control ECU) 1.323,0.979 1.583,1.156 0.26,0.177 10 false E77 0.885,1.969 1.396,2.135 0.51,0.167 10 false 8 (PIG) 1.604,1.969 2.271,2.115 0.667,0.146 10 false 7 (PGND) 0.25,1.969 0.667,2.135 0.417,0.167 10 false 3 (IG)

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E77-3 (IG) -
Body ground
Engine switch on (IG) 11 to 14 V
E77-8 (PIG) -
Body ground



b.

Turn the engine switch off.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E77-7 (PGND) -
Body ground
Always Below 1 Ω


Result
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C