Home › Steering › VARIABLE GEAR RATIO STEERING › VARIABLE GEAR RATIO STEERING SYSTEM › 2014.08–2015.08
RM2660E _55 Steering _052825 VARIABLE GEAR RATIO STEERING _0255448 VARIABLE GEAR RATIO STEERING SYSTEM C

VARIABLE GEAR RATIO STEERING  VARIABLE GEAR RATIO STEERING SYSTEM  C1595/55  Lost Communication with Steering Angle Sensor Module  C15C4/68  Steering Angle Signal (Test Mode DTC)  


DESCRIPTION

Signal transmission between the steering control ECU and steering angle sensor is performed via serial communication.

If an error occurs between them in serial communication, the ECU will store DTC C1595/55.

DTC Code DTC Detection Condition Trouble Area
C1595/55 The steering control ECU detects an error in serial communication between the ECU and steering angle sensor.
·

Steering angle sensor

·

Steering control ECU

·

Harness or connector


C15C4/68 A steering signal indicating a tire angle of 36° or more (to the left or right) is input after entering test mode.*
·

Steering angle sensor

·

Steering control ECU

·

Harness or connector



HINT:

*: A tire angle of 36° and a motor rotation angle of 36° correspond to the steering wheel angle. The amount of change in tire angle and motor rotation angle is from when the mode is changed to test mode.


WIRING DIAGRAM

C163898E11
0.26,2.01 2.063,2.24 1.802,0.229 10 false Steering Angle Sensor 5.677,1.906 7.073,2.146 1.396,0.24 10 false Steering Control ECU 6.031,0.75 6.563,1 0.531,0.25 10 false SS1+ 6.031,1.344 6.531,1.594 0.5,0.25 10 false SS1- 5.75,0.646 6.031,0.865 0.281,0.219 10 false 19 5.677,1.729 6.073,1.938 0.396,0.208 10 false E79 5.75,1.24 6.031,1.458 0.281,0.219 10 false 10 0.729,0.75 1.188,1 0.458,0.25 10 false SS1+ 0.74,1.333 1.177,1.583 0.438,0.25 10 false SS1- 1.208,0.656 1.49,0.875 0.281,0.219 10 false 8 1.208,1.24 1.49,1.458 0.281,0.219 10 false 7 0.26,1.833 0.698,2.083 0.438,0.25 10 false E11

PROCEDURE

1.CHECK DTC (CAN COMMUNICATION SYSTEM)
a.

Check for DTCs in the CAN communication system (for LHD: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>DIAGNOSIS SYSTEM, for RHD: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
DTC is not output A
DTC is output (for LHD) B
DTC is output (for RHD) C



A

2.CHECK STEERING ANGLE SENSOR

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

C

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

2.CHECK STEERING ANGLE SENSOR
a.

Check if a steering angle sensor that complies with the vehicle specifications is installed.

OK:

A steering angle sensor that complies with the vehicle specification is installed.




OK

3.CHECK HARNESS AND CONNECTOR (STEERING CONTROL ECU - STEERING ANGLE SENSOR)

NG

3.CHECK HARNESS AND CONNECTOR (STEERING CONTROL ECU - STEERING ANGLE SENSOR)
U164537E02
1.365,2.292 1.156,2.531 false 1.323,2.229 1.135,2.063 false 5.25,1.896 4.906,2.406 false 5.323,1.896 5.563,2.406 false 0.74,0.125 3.229,0.521 2.49,0.396 10 false Rear view of wire harness connector: (to Steering Control ECU) 0.531,1.99 1.177,2.177 0.646,0.188 10 false 10 (SS1-) 0.521,2.469 1.177,2.656 0.656,0.188 10 false 19 (SS1+) 5.406,2.427 6.01,2.615 0.604,0.188 10 false 7 (SS1-) 4.615,2.427 5.229,2.615 0.615,0.188 10 false 8 (SS1+) 1.396,1.219 1.688,1.385 0.292,0.167 10 false E79 4.594,1.292 4.885,1.458 0.292,0.167 10 false E11 4.365,0.125 6.854,0.521 2.49,0.396 10 false Rear view of wire harness connector: (to Steering Angle Sensor)

a.

Disconnect the E79 steering control ECU connector.


b.

Disconnect the E11 steering angle sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E79-10 (SS1-) - E11-7 (SS1-) Always Below 1 Ω
E79-19 (SS1+) - E11-8 (SS1+)
E79-19 (SS1+) - Body ground Always 10 kΩ or higher
E79-10 (SS1-) - Body ground
E79-19 (SS1+) - E79-10 (SS1-)




OK

4.CHECK STEERING ANGLE SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK STEERING ANGLE SENSOR
a.
C358495E01
0.792,1.125 1.167,1.354 0.375,0.229 0.625,2.083 0.802,2.219 false 0.531,2.573 0.844,2.271 false 0.177,0.115 2.438,0.49 2.26,0.375 10 false Rear view of wire harness connector: (to Steering Control ECU) 0.854,1.167 1.25,1.344 0.396,0.177 10 false E79 0.042,2 0.823,2.177 0.781,0.177 10 false 10 (SS1-) 0.156,2.615 0.938,2.792 0.781,0.177 10 false 19 (SS1+) 0.354,3.708 1.135,3.885 0.781,0.177 10 false GND

Disconnect the E79 steering control ECU connector.


b.

Move the shift lever to N.


c.

Jack up the vehicle.


d.

Check the waveform of the steering angle sensor using an oscilloscope.

HINT:

The voltage must be measured with the steering angle sensor connector connected.


Standard Voltage:
Tester Connection Switch Condition Specified Condition
E79-19 (SS1+) - E79-10 (SS1-) Engine switch on (IG), steering wheel rotated slowly Pulse generation
(0 to 5 V)


HINT:

The output voltage should fluctuate up and down similarly to the diagram when the wheel is turned slowly.


Result
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C



A

B

C