Home › Steering › VARIABLE GEAR RATIO STEERING › VARIABLE GEAR RATIO STEERING SYSTEM › 2014.08–2015.08
RM2660E _55 Steering _052825 VARIABLE GEAR RATIO STEERING _0255448 VARIABLE GEAR RATIO STEERING SYSTEM C

VARIABLE GEAR RATIO STEERING  VARIABLE GEAR RATIO STEERING SYSTEM  C15C1/74  Steering Angle Sensor Malfunction  C15C2/74  Steering Angle Sensor B+ Malfunction  


DESCRIPTION

The steering control ECU detects a steering angle sensor malfunction by receiving an error signal from the steering angle sensor via CAN communication. If the steering control ECU detects this error signal, it will turn the master warning light on, store these DTCs, and stop VGRS operation.

DTC Code DTC Detection Condition Trouble Area
C15C1/74 The steering control ECU receives a steering angle sensor malfunction signal via CAN communication.
·

Steering angle sensor

·

Harness or connector

·

CAN communication system

·

Steering control ECU


C15C2/74 The steering control ECU receives a B+ open circuit signal from the steering angle sensor via CAN communication.
·

Steering angle sensor

·

Harness or connector

·

CAN communication system

·

Steering control ECU



WIRING DIAGRAM

C149147E22
0.104,5.063 2.344,5.26 2.24,0.198 10 false Steering Angle Sensor 5.698,5.125 7.115,5.333 1.417,0.208 10 false Steering Control ECU 5.948,0.927 6.25,1.115 0.302,0.188 10 false E79 5.938,1.406 6.24,1.594 0.302,0.188 10 false E79 5.948,2.479 6.25,2.667 0.302,0.188 10 false E79 5.948,4.229 6.25,4.417 0.302,0.188 10 false E77 0.906,0.792 1.177,0.979 0.271,0.188 10 false 10 0.948,1.26 1.219,1.448 0.271,0.188 10 false 9 0.948,2.281 1.219,2.469 0.271,0.188 10 false 3 0.948,3.677 1.219,3.865 0.271,0.188 10 false 2 0.938,3.083 1.208,3.271 0.271,0.188 10 false 1 6,4 6.271,4.188 0.271,0.188 10 false 10 6.042,0.719 6.313,0.906 0.271,0.188 10 false 9 6.042,2.271 6.313,2.458 0.271,0.188 10 false 1 6,1.198 6.271,1.385 0.271,0.188 10 false 20 6.313,0.917 6.792,1.115 0.479,0.198 10 false CANH 6.313,1.396 6.792,1.594 0.479,0.198 10 false CANL 6.313,2.479 6.813,2.708 0.5,0.229 10 false +BO 6.313,4.229 6.813,4.458 0.5,0.229 10 false +BI 0.417,0.927 0.896,1.125 0.479,0.198 10 false CANH 0.427,1.396 0.906,1.594 0.479,0.198 10 false CANL 0.5,2.469 0.979,2.667 0.479,0.198 10 false BAT 0.49,3.823 0.844,4.021 0.354,0.198 10 false ESS 0.604,3.229 0.844,3.417 0.24,0.188 10 false IG 1.271,3.396 2.427,3.646 1.156,0.25 10 false ECU-IG No. 2 4.615,4.385 5.354,4.594 0.74,0.208 10 false ECU-B1 2.927,3.219 4.219,3.427 1.292,0.208 10 false from IG Circuit 3.115,4.219 3.938,4.406 0.823,0.188 10 false from Battery 0.104,4.906 0.458,5.104 0.354,0.198 10 false E11

PROCEDURE

1.CHECK DTC (CAN COMMUNICATION SYSTEM)
a.

Using the intelligent tester, check if the CAN communication system is functioning normally (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>DIAGNOSIS SYSTEM for LHD, Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>DIAGNOSIS SYSTEM for RHD).

Result
Result Proceed to
DTC is not output A
DTC is output (for LHD) B
DTC is output (for RHD) C



A

2.CHECK HARNESS AND CONNECTOR (STEERING CONTROL ECU +BI TERMINAL VOLTAGE)

B

GO TO CAN COMMUNICATION SYSTEM (DIAGNOSTIC TROUBLE CODE CHART)

C

GO TO CAN COMMUNICATION SYSTEM (DIAGNOSTIC TROUBLE CODE CHART)

2.CHECK HARNESS AND CONNECTOR (STEERING CONTROL ECU +BI TERMINAL VOLTAGE)
a.
U164528E02
1.219,1.583 1.073,1.948 false 0.156,0.083 2.646,0.479 2.49,0.396 10 false Component with harness connected: (Steering Control ECU) 1.302,0.99 1.563,1.167 0.26,0.177 10 false E77 0.917,1.969 1.531,2.135 0.615,0.167 10 false 10 (+BI)

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E77-10 (+BI) - Body ground Always 11 to 14 V




OK

3.CHECK STEERING CONTROL ECU (+BO TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK STEERING CONTROL ECU (+BO TERMINAL VOLTAGE)
a.
U164524E02
1.094,1.573 1.24,1.99 true 0.156,0.094 2.646,0.49 2.49,0.396 10 false Component with harness connected: (Steering Control ECU) 0.813,0.99 1.073,1.167 0.26,0.177 10 false E79 0.979,1.969 1.583,2.135 0.604,0.167 10 false 1 (+BO)

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E79-1 (+BO) - Body ground Always 11 to 14 V


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

4.CHECK HARNESS AND CONNECTOR (STEERING ANGLE SENSOR)

B

C

4.CHECK HARNESS AND CONNECTOR (STEERING ANGLE SENSOR)
a.
U166651E02
2.292,2.354 2.708,1.938 false 2.646,2.76 2.385,2.354 false 0.094,0.063 2.344,0.458 2.25,0.396 10 false Rear view of wire harness connector: (to Steering Angle Sensor) 2.771,1.823 3.396,2.042 0.625,0.219 10 false 2 (ESS) 2.74,2.24 3.365,2.458 0.625,0.219 10 false E11 2.583,2.813 3.042,3.031 0.458,0.219 10 false 1 (IG)

Disconnect the E11 steering angle sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E11-1 (IG) - Body ground Engine switch on (IG) 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E11-2 (ESS) - Body ground Always Below 1 Ω




OK

5.CHECK STEERING ANGLE SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK STEERING ANGLE SENSOR
a.
U166652E02
2.302,2.354 2.76,1.854 false 2.198,2.354 2.594,2.781 false 2.792,1.76 3.292,1.958 0.5,0.198 10 false 2 (ESS) 2.667,2.719 3.229,2.917 0.563,0.198 10 false 3 (BAT) 2.74,2.229 3.021,2.427 0.281,0.198 10 false E11 0.094,0.115 2.448,0.49 2.354,0.375 10 false Rear view of wire harness connector: (to Steering Angle Sensor)

Disconnect the E11 steering angle sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E11-3 (BAT) - E11-2 (ESS) Engine switch on (IG) 11 to 14 V




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR