Home › Steering › VARIABLE GEAR RATIO STEERING › VARIABLE GEAR RATIO STEERING SYSTEM › from 2015.08
RM2660E _55 Steering _052825 VARIABLE GEAR RATIO STEERING _0255448 VARIABLE GEAR RATIO STEERING SYSTEM C

VARIABLE GEAR RATIO STEERING  VARIABLE GEAR RATIO STEERING SYSTEM  C15C6/77  IG Power Supply Voltage  


DESCRIPTION

The VGRS ECU (steering control ECU) monitors the IG power supply voltage.

If the VGRS ECU (steering control ECU) detects a malfunction, it turns the master warning light on, and stores DTC C15C6/77.

DTC No. DTC Detection Condition Trouble Area
C15C6/77 Both conditions are met for approximately 3 seconds or more:
·

The engine switch is on (IG).

·

When the difference between the IG and PIG voltages is 4 V or more or the IG voltage is 18.5 V or higher, an open or short in the IG circuit or an internal malfunction in the ECU is detected.


·

ECU-IG NO. 1 fuse

·

Battery

·

Charging system

·

VGRS ECU (steering control ECU)

·

Harness or connector



WIRING DIAGRAM

C344558E05
1.135,0.281 2.125,0.49 0.99,0.208 10 false from IG Circuit 4.323,2 6.552,2.24 2.229,0.24 10 false VGRS ECU (Steering Control ECU) 3.26,0.417 4.188,0.635 0.927,0.219 10 false ECU-IG NO. 1 5.313,0.313 5.719,0.51 0.406,0.198 10 false IG 5.26,1.385 5.729,1.583 0.469,0.198 10 false PGND 5,0.104 5.135,0.281 0.135,0.177 10 false 4 4.854,0.313 5.26,0.49 0.406,0.177 10 false E161 5,1.198 5.135,1.375 0.135,0.177 10 false 1 4.854,1.385 5.26,1.563 0.406,0.177 10 false E159 1.26,0.948 2.25,1.156 0.99,0.208 10 false from Battery 3.469,1.083 4.167,1.302 0.698,0.219 10 false VGRS 4.854,0.958 5.26,1.135 0.406,0.177 10 false E159 5,0.74 5.135,0.917 0.135,0.177 10 false 2 5.281,0.948 5.688,1.146 0.406,0.198 10 false PIG

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the VGRS ECU (steering control ECU), perform actuator angle neutral point calibration and initialization after replacement (See page Steering>VARIABLE GEAR RATIO STEERING>VARIABLE GEAR RATIO STEERING SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (IG, PGND TERMINAL)
a.

Turn the engine switch on (IG).


b.
U165230E02
2.531,1.052 2.781,1.49 2.781,1.49 2.781,1.635 false 1.635,1.156 1.917,1.531 1.917,1.531 1.917,1.688 false 0.073,0.083 0.313,0.271 0.24,0.188 10 false *a 1.521,1.698 2.156,1.875 0.635,0.177 10 false 1 (PGND) 2.552,1.667 2.948,1.865 0.396,0.198 10 false 4 (IG) 1.396,0.313 1.75,0.479 0.354,0.167 10 false E159 2.26,0.313 2.615,0.479 0.354,0.167 10 false E161

Measure the voltage according to the value(s) in the table below.

HINT:

With the connector connected to the VGRS ECU (steering control ECU), measure the voltage from the rear of the connector.


Standard Voltage:
Tester Connection Condition Specified Condition
E161-4 (IG) - E159-1 (PGND) Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Component with harness connected
(VGRS ECU [Steering Control ECU])

Result
Result Proceed to
The voltage is in the range of 11 to 14 V A
The voltage is below 11 V B
The voltage is higher than 14 V C


HINT:



A

2.READ VALUE USING GTS (IG POWER SUPPLY VOLTAGE)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

C

CHECK OR REPLACE CHARGING SYSTEM OR BATTERY

2.READ VALUE USING GTS (IG POWER SUPPLY VOLTAGE)
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / VGRS / Data List.

VGRS
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
IG Power Supply Voltage IG power supply voltage/
Min.: 0.00 V
Max.: 255.99 V
11 to 14 V -

Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C

OK:

11 to 14 V




A

B

REPLACE VGRS ECU (STEERING CONTROL ECU)

C

REPLACE VGRS ECU (STEERING CONTROL ECU)