Home › Steering › VARIABLE GEAR RATIO STEERING › VARIABLE GEAR RATIO STEERING SYSTEM › from 2015.08
RM2660E _55 Steering _052825 VARIABLE GEAR RATIO STEERING _0255448 VARIABLE GEAR RATIO STEERING SYSTEM C

VARIABLE GEAR RATIO STEERING  VARIABLE GEAR RATIO STEERING SYSTEM  C15C7/78  DC Motor Power Source Voltage  C15C8/79  Power Supply Relay Failure  


DESCRIPTION

The VGRS ECU (steering control ECU) monitors terminal PIG (motor power source voltage) in order to detect malfunctions in the power supply relay (located inside the VGRS ECU (steering control ECU)).

If the VGRS ECU (steering control ECU) detects a malfunction, it turns the master warning light on, and stores these DTCs.

DTC No. DTC Detection Condition Trouble Area
C15C7/78 Both conditions are met for approximately 2.4 seconds or more:
·

The engine switch is on (IG).

·

When the PIG voltage is 18.5 V or higher or 7 V or less, an open or short in the PIG circuit, or an internal malfunction in the ECU is detected.


·

VGRS fuse

·

Battery

·

Charging system

·

VGRS ECU (steering control ECU)

·

Harness or connector


C15C8/79 All conditions are met for approximately 1.5 seconds or more:
·

The engine switch is on (IG).

·

Control has not started.

·

An open / short in the PIG circuit or an internal malfunction in the ECU is detected.


·

VGRS fuse

·

Battery

·

Charging system

·

VGRS ECU (steering control ECU)

·

Harness or connector



WIRING DIAGRAM

C288141E08
1.302,0.521 2.115,0.74 0.813,0.219 10 false from Battery 3.438,0.677 3.896,0.865 0.458,0.188 10 false VGRS 5.188,2.073 6.604,2.49 1.417,0.417 10 false VGRS ECU (Steering Control ECU) 5.25,0.5 5.708,0.698 0.458,0.198 10 false PIG 5.26,1 5.875,1.198 0.615,0.198 10 false PGND 5.271,1.51 5.885,1.708 0.615,0.198 10 false PGD2 4.854,0.5 5.313,0.698 0.458,0.198 10 false E159 4.844,1.01 5.302,1.208 0.458,0.198 10 false E159 4.844,1.51 5.458,1.708 0.615,0.198 10 false E161 4.979,0.333 5.135,0.531 0.156,0.198 10 false 2 4.969,0.844 5.125,1.042 0.156,0.198 10 false 1 4.938,1.344 5.25,1.542 0.313,0.198 10 false 13

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the VGRS ECU (steering control ECU), perform actuator angle neutral point calibration and initialization after replacement (See page Steering>VARIABLE GEAR RATIO STEERING>VARIABLE GEAR RATIO STEERING SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.READ VALUE USING GTS (PIG POWER SUPPLY VOLTAGE)
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / VGRS / Data List.

VGRS
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
PIG Power Supply Voltage PIG power supply voltage/
Min.: 0.00 V
Max.: 255.99 V
11 to 14 V -



OK

NG

2.INSPECT VGRS ECU (STEERING CONTROL ECU) (PIG, PGND TERMINAL)
2.INSPECT VGRS ECU (STEERING CONTROL ECU) (PIG, PGND TERMINAL)
a.

Turn the engine switch off.


b.

Check the connection of the VGRS ECU (steering control ECU) connector and the condition of the terminals.


c.
C256581E02
1.49,1 1.156,1.521 1.156,1.521 1.156,1.656 true 1.604,1 1.979,1.552 1.979,1.552 1.979,1.667 true 0.094,0.042 0.281,0.219 0.188,0.177 10 false *a 0.917,1.719 1.427,1.896 0.51,0.177 10 false 2 (PIG) 1.656,1.729 2.323,1.906 0.667,0.177 10 false 1 (PGND)

Disconnect the E159 VGRS ECU (steering control ECU) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (PIG) - 1 (PGND) Always 100 kΩ or higher


Text in Illustration
*a Component without harness connected
(VGRS ECU [Steering Control ECU])

Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

3.CHECK HARNESS AND CONNECTOR (PGND, PGD2 TERMINAL)

B

REPLACE VGRS ECU (STEERING CONTROL ECU)

C

REPLACE VGRS ECU (STEERING CONTROL ECU)

3.CHECK HARNESS AND CONNECTOR (PGND, PGD2 TERMINAL)
a.

Turn the engine switch off.


b.
U165260E02
1.406,1.448 0.885,1.76 0.885,1.76 0.885,1.927 false 2.302,3.771 2.781,4.021 2.781,4.021 2.781,4.219 false 1.552,0.313 1.917,0.479 0.365,0.167 10 false E159 1.552,2.656 1.917,2.823 0.365,0.167 10 false E161 0.104,0.073 0.313,0.25 0.208,0.177 10 false *a 0.646,1.969 1.083,2.156 0.438,0.188 10 false PGND 2.531,4.26 2.938,4.427 0.406,0.167 10 false PGD2

Disconnect the E161 and E159 VGRS ECU (steering control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E159-1 (PGND) - Body ground Always Below 1 Ω
E161-13 (PGD2) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to VGRS ECU [Steering Control ECU])



OK

4.CHECK HARNESS AND CONNECTOR (PIG, PGND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (PIG, PGND TERMINAL)
a.

Turn the engine switch off.


b.
U165256E02
1.375,1.281 0.958,1.594 0.958,1.594 0.958,1.729 false 2.01,1.281 2.427,1.594 2.427,1.594 2.427,1.729 false 0.104,0.083 0.292,0.24 0.188,0.156 10 false *a 1.521,0.292 1.885,0.448 0.365,0.156 10 false E159 0.708,1.76 1.156,1.927 0.448,0.167 10 false PGND 2.281,1.76 2.552,1.927 0.271,0.167 10 false PIG

Disconnect the E159 VGRS ECU (steering control ECU) connector.


c.

Measure the voltage according to the value(s) in the table below.

HINT:

With the connector connected to the VGRS ECU (steering control ECU), measure the voltage from the rear of the connector.


Standard Voltage:
Tester Connection Condition Specified Condition
E159-2 (PIG) - E159-1 (PGND) Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to VGRS ECU [Steering Control ECU])

Result
Result Proceed to
The voltage is in the range of 11 to 14 V (for LHD) A
The voltage is in the range of 11 to 14 V (for RHD) B
The voltage is below 11 V C
The voltage is higher than 14 V D



A

REPLACE VGRS ECU (STEERING CONTROL ECU)

B

REPLACE VGRS ECU (STEERING CONTROL ECU)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

D

CHECK OR REPLACE CHARGING SYSTEM OR BATTERY