Home › Steering › STEERING COLUMN › HEATED STEERING WHEEL SYSTEM › 2014.08–2015.08
RM2660E _55 Steering _052826 STEERING COLUMN _0255459 HEATED STEERING WHEEL SYSTEM J

STEERING COLUMN  HEATED STEERING WHEEL SYSTEM  Steering Wheel does not Heat Up When Heated Steering Wheel Switch is Pressed  


WIRING DIAGRAM

C253489E09
2.563,0.771 2.688,0.948 0.125,0.177 10 false + 2.146,1.156 2.292,1.323 0.146,0.167 10 false IG 2.521,1.51 2.688,1.688 0.167,0.177 10 false IN 2.792,0.688 2.958,0.844 0.167,0.156 10 false 7 1.906,1.042 2.135,1.25 0.229,0.208 10 false 3 2.781,1.417 2.927,1.563 0.146,0.146 10 false 6 1.74,2.031 3.219,2.271 1.479,0.24 10 false Steering Heater Switch 1.25,1.292 1.74,1.49 0.49,0.198 10 false LH-IG 3.521,0.667 3.823,0.823 0.302,0.156 10 false BTM 3.24,0.573 3.385,0.708 0.146,0.135 10 false 1 3.25,3.26 3.396,3.448 0.146,0.188 10 false 2 3.25,1.302 3.396,1.448 0.146,0.146 10 false 3 3.26,2.542 3.406,2.708 0.146,0.167 10 false 4 4.292,0.563 4.438,0.729 0.146,0.167 10 false 1 4.302,3.26 4.458,3.427 0.156,0.167 10 false 3 4.302,1.292 4.448,1.448 0.146,0.156 10 false 2 4.302,2.542 4.469,2.698 0.167,0.156 10 false 4 3.521,1.406 3.844,1.573 0.323,0.167 10 false ETM 3.51,2.656 3.865,2.823 0.354,0.167 10 false BHT 3.521,3.375 3.844,3.542 0.323,0.167 10 false EHT 4.917,0.792 5.219,1 0.302,0.208 10 false CCU 4.917,1.521 5.219,1.708 0.302,0.188 10 false CCV 4.917,2.76 5.25,2.948 0.333,0.188 10 false CCW 4.927,3.479 5.219,3.656 0.292,0.177 10 false CCX 5.281,1.521 5.542,1.708 0.26,0.188 10 false TH2 5.271,2.771 5.563,2.958 0.292,0.188 10 false SH1 5.271,3.49 5.531,3.677 0.26,0.188 10 false SH2 3.167,3.938 4.469,4.313 1.302,0.375 10 false Spiral with Sensor Cable Sub-assembly 4.76,3.927 5.708,4.5 0.948,0.573 10 false Steering Wheel Heater Control Assembly 6.094,3.938 7.063,4.313 0.969,0.375 10 false Steering Wheel Assembly 5.698,0.771 5.865,0.948 0.167,0.177 10 false B 4.219,0.76 4.448,0.969 0.229,0.208 10 false z63 3.135,0.771 3.479,0.927 0.344,0.156 10 false E107 4.646,0.76 4.823,0.979 0.177,0.219 10 false A 1.74,1.865 1.99,2.01 0.25,0.146 10 false G14 1.135,2.927 2.271,3.25 1.135,0.323 10 false STRG HTR 0.104,1.094 0.865,1.5 0.76,0.406 10 false from IG1 NO. 1 Relay 0.073,2.667 0.854,3.042 0.781,0.375 10 false from STRG HTR Relay 4.656,1.5 4.823,1.698 0.167,0.198 10 false A 4.656,2.74 4.802,2.958 0.146,0.219 10 false A 4.656,3.469 4.792,3.646 0.135,0.177 10 false A 4.656,0.563 4.802,0.729 0.146,0.167 10 false 1 4.677,1.292 4.823,1.448 0.146,0.156 10 false 2 4.667,2.531 4.833,2.688 0.167,0.156 10 false 4 4.667,3.26 4.823,3.427 0.156,0.167 10 false 3 5.271,0.792 5.563,0.979 0.292,0.188 10 false TH1 5.698,1.5 5.875,1.719 0.177,0.219 10 false B 5.698,2.74 5.885,2.948 0.188,0.208 10 false B 5.698,3.469 5.896,3.719 0.198,0.25 10 false B 5.698,0.563 5.844,0.729 0.146,0.167 10 false 1 5.708,1.292 5.854,1.448 0.146,0.156 10 false 2 5.708,2.531 5.875,2.688 0.167,0.156 10 false 4 5.708,3.26 5.865,3.427 0.156,0.167 10 false 3 3.135,1.5 3.479,1.656 0.344,0.156 10 false E107 3.135,2.74 3.479,2.896 0.344,0.156 10 false E107 3.135,3.469 3.479,3.625 0.344,0.156 10 false E107 4.229,2.74 4.458,2.948 0.229,0.208 10 false z63 4.219,1.49 4.448,1.698 0.229,0.208 10 false z63 4.219,3.469 4.448,3.677 0.229,0.208 10 false z63

CAUTION / NOTICE / HINT

HINT:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

The steering heater unit is built into the steering wheel assembly which cannot be disassembled. Therefore, when the steering heater unit has a malfunction, replace the steering wheel assembly.



PROCEDURE

1.INSPECT STEERING WHEEL ASSEMBLY (THERMISTOR, HEATER, THERMOSTAT)
a.
U111207E06
0.99,1.708 1.198,1.396 false 1.563,1.427 1.49,1.719 false 1.979,1.719 1.917,1.427 false 2.25,1.417 2.469,1.698 false 0.854,1.719 1.135,1.906 0.281,0.188 10 false TH1 1.344,1.74 1.698,1.906 0.354,0.167 10 false TH2 1.844,1.74 2.354,1.927 0.51,0.188 10 false SH2 2.365,1.719 2.771,1.927 0.406,0.208 10 false SH1 0.323,0.188 0.604,0.375 0.281,0.188 10 false *a 0.927,0.75 1.083,0.938 0.156,0.188 10 false B

Disconnect the B steering wheel controller connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-1 (TH1) - B-2 (TH2) 10 to 30°C (50 to 86°F) 8.132 to 18.43 kΩ
B-4 (SH1) - B-3 (SH2) 20°C (68°F) 1.89 to 2.25 Ω


Text in Illustration
*a Front view of wire harness connector
(to Steering Wheel Control Assembly)



OK

2.INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

NG

REPLACE STEERING WHEEL ASSEMBLY

2.INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY
a.

Check the connectors and cables of the spiral with sensor cable sub-assembly.

OK:

There are no defects such as scratches, cracks, dents or damage on the connectors or cables.



b.

Disconnect the E107 and z63 spiral with sensor cable sub-assembly connectors.

U165104E02
0.49,0.708 0.646,0.708 0.646,0.708 0.896,0.885 true 0.5,1.177 0.635,1.177 0.635,1.177 0.885,1.094 true 1.5,1.188 1.396,1.188 1.396,1.188 1.156,1.094 true 1.479,0.719 1.385,0.719 1.385,0.719 1.146,0.885 true 4.75,1.417 4.896,1.417 4.896,1.417 5.104,1.563 true 4.75,1.917 4.865,1.917 4.865,1.917 5.104,1.792 true 5.729,1.406 5.615,1.406 5.615,1.406 5.375,1.542 true 5.719,1.906 5.604,1.906 5.604,1.906 5.385,1.792 true 0.219,0.104 0.427,0.365 0.208,0.26 10 false *a 1.531,0.646 2.031,0.885 0.5,0.24 10 false BTM 1.542,1.115 2,1.323 0.458,0.208 10 false ETM 0.167,0.625 0.625,0.885 0.458,0.26 10 false EHT 0.188,1.104 0.563,1.333 0.375,0.229 10 false BHT 0.875,0.26 1.292,0.49 0.417,0.229 10 false E107 5.188,0.875 5.438,1.042 0.25,0.167 10 false z63 5.781,1.313 6.208,1.521 0.427,0.208 10 false CCV 5.781,1.823 6.177,2.01 0.396,0.188 10 false CCW 4.406,1.323 4.865,1.542 0.458,0.219 10 false CCU 4.438,1.833 4.823,2.021 0.385,0.188 10 false CCX


c.

Disconnect the heated steering wheel controller connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z63-1 (CCU) - E107-1 (BTM) Always Below 1 Ω
z63-2 (CCV) - E107-3 (ETM) Always Below 1 Ω
z63-3 (CCX) - E107-2 (EHT) Always Below 1 Ω
z63-4 (CCW) - E107-4 (BHT) Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Spiral with Sensor Cable Sub-assembly)
- -



OK

3.CHECK STEERING HEATER SWITCH

NG

REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

3.CHECK STEERING HEATER SWITCH
a.
U165105E02
1.229,1.708 1.354,1.708 1.354,1.708 1.49,1.271 true 1.583,1.271 1.583,1.74 true 2.063,1.698 1.969,1.698 1.969,1.698 1.854,1.281 true 1.104,1.615 1.229,1.781 0.125,0.167 10 false + 1.531,1.771 1.74,1.938 0.208,0.167 10 false IN 2.125,1.625 2.375,1.813 0.25,0.188 10 false IG 0.521,0.49 0.823,0.677 0.302,0.188 10 false G14 0.156,0.135 0.365,0.323 0.208,0.188 10 false *a

Disconnect the G14 steering heater switch connector.


b.

Measure the voltage according to the value(s) in the table below.

HINT:

As the circuit has a diode, perform the measurement in diode test mode, and do not mistake the polarity.


Standard Voltage:
Tester Connection
(Positive (+) tester probe - Negative (-) tester probe)
Condition Specified Condition
G14-3 (IG) - G14-7 (+) Always Below 1.25 V
G14-6 (IN) - G14-7 (+) Steering heater switch is pushed Below 1.25 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G14-3 (IG) - G14-6 (IN) Steering heater switch is pushed Below 1 Ω
G14-3 (IG) - G14-6 (IN) Steering heater switch is not pushed 10 kΩ or higher



Text in Illustration
*a Component without harness connected
(Steering Heater Switch)


OK

4.CHECK HARNESS AND CONNECTOR (STEERING HEATER SWITCH - SPIRAL W/ SENSOR CABLE SUB-ASSEMBLY)

NG

REPLACE STEERING HEATER SWITCH

4.CHECK HARNESS AND CONNECTOR (STEERING HEATER SWITCH - SPIRAL W/ SENSOR CABLE SUB-ASSEMBLY)
a.

Disconnect the G14 steering heater switch connector.


b.

Disconnect the E107 spiral with sensor cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G14-7 (+) - E107-1 (BTM) Always Below 1 Ω
G14-6 (IN) - E107-3 (ETM) Always Below 1 Ω




OK

5.CHECK HARNESS AND CONNECTOR (IG CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (IG CIRCUIT)
a.

Disconnect the G14 steering heater switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G14-3 (IG) - Body ground Ignition switch ON 11 to 14 V




OK

6.CHECK HARNESS AND CONNECTOR (IG CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (IG CIRCUIT)
a.

Disconnect the E107 spiral with sensor cable subassembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E107-4 (BHT) - Body ground Ignition switch ON 11 to 14 V




OK

7.CHECK HARNESS AND CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY BODY GROUND)
a.

Disconnect the E107 spiral with sensor cable sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E107-2 (EHT) - Body ground Always Below 1 Ω




OK

REPLACE STEERING WHEEL HEATER CONTROL ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR