Inspect the fuses for circuits related to this system before performing the following inspection procedure.
The steering heater unit is built into the steering wheel assembly which cannot be disassembled. Therefore, when the steering heater unit has a malfunction, replace the steering wheel assembly.
Disconnect the B steering wheel heater control connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-1 (TH1) - B-2 (TH2) | 10 to 30°C (50 to 86°F) | 8.132 to 18.43 kΩ |
| B-4 (SH1) - B-3 (SH2) | 20°C (68°F) | 1.89 to 2.25 Ω |
| *a | Component without harness connected
(Steering Wheel Assembly) |
OK
NG
Check the connectors and cables of the spiral cable sub-assembly.
There are no defects such as scratches, cracks, dents or damage on the connectors or cables.
Disconnect the E140*1 or E107*2 and z74 spiral cable sub-assembly connectors.
*1: w/ Door Ajar Warning Buzzer
*2: w/o Door Ajar Warning Buzzer
| *A | w/ Door Ajar Warning Buzzer | *B | w/o Door Ajar Warning Buzzer |
| *a | Component without harness connected
(Spiral Cable Sub-assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z74-1 - E140-1 (BTM) | Always | Below 1 Ω |
| z74-2 - E140-3 (ETM) | Always | Below 1 Ω |
| z74-3 - E140-2 (EHT) | Always | Below 1 Ω |
| z74-4 - E140-4 (BHT) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z74-1 - E107-1 (BTM) | Always | Below 1 Ω |
| z74-2 - E107-3 (ETM) | Always | Below 1 Ω |
| z74-3 - E107-2 (EHT) | Always | Below 1 Ω |
| z74-4 - E107-4 (BHT) | Always | Below 1 Ω |
OK
NG
Remove the steering heater switch (See page Steering>STEERING COLUMN>STEERING HEATER SWITCH>REMOVAL).
Inspect the steering heater switch (See page Steering>STEERING COLUMN>STEERING HEATER SWITCH>INSPECTION).
OK
NG
Disconnect the V7 steering heater switch connector.
Disconnect the E140*1 or E107*2 spiral cable sub-assembly connector.
*1: w/ Door Ajar Warning Buzzer
*2: w/o Door Ajar Warning Buzzer
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V7-4 (+) - E140-1 (BTM) | Always | Below 1 Ω |
| V7-8 (IN) - E140-3 (ETM) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V7-4 (+) - E107-1 (BTM) | Always | Below 1 Ω |
| V7-8 (IN) - E107-3 (ETM) | Always | Below 1 Ω |
OK
NG
Disconnect the V7 steering heater switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| V7-1 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
OK
NG
Disconnect the E140*1 or E107*2 spiral cable sub-assembly connector.
*1: w/ Door Ajar Warning Buzzer
*2: w/o Door Ajar Warning Buzzer
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E140-4 (BHT) - Body ground | Ignition switch ON | 11 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E107-4 (BHT) - Body ground | Ignition switch ON | 11 to 14 V |
OK
NG
Disconnect the E140*1 or E107*2 spiral cable sub-assembly connector.
*1: w/ Door Ajar Warning Buzzer
*2: w/o Door Ajar Warning Buzzer
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E140-2 (EHT) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E107-2 (EHT) - Body ground | Always | Below 1 Ω |
OK
NG