Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(w/ Navigation System) › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255478 AUDIO AND VISUAL SYSTEM(w/ Navigation System) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(w/ Navigation System)  Illumination Circuit  


DESCRIPTION

Power is supplied to the multi-media module receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E248927E03
3.875,3.823 4.823,4.208 0.948,0.385 10 false Spiral Cable Sub-assembly 0.896,6.125 2.906,6.344 2.01,0.219 10 false Steering Pad Switch Assembly 5.792,3.844 7.063,4.229 1.271,0.385 10 false Multi-media Module Receiver Assembly 4.135,3.188 4.5,3.333 0.365,0.146 10 false EAU 4.135,1.781 4.5,1.927 0.365,0.146 10 false IL+2 6.156,3.073 6.594,3.292 0.438,0.219 10 false SWG 5.865,2.927 6.094,3.115 0.229,0.188 10 false 32 3.573,3.073 3.979,3.271 0.406,0.198 10 false z36 3.635,2.854 3.823,3.052 0.188,0.198 10 false 8 3.563,1.646 3.958,1.885 0.396,0.24 10 false z36 3.656,1.406 3.823,1.594 0.167,0.188 10 false 5 4.75,3.083 5.167,3.344 0.417,0.26 10 false E12 4.844,2.844 5.042,3.063 0.198,0.219 10 false 4 4.75,1.646 5.177,1.896 0.427,0.25 10 false E12 4.792,1.427 5.042,1.635 0.25,0.208 10 false 12 6.115,0.594 6.531,0.844 0.417,0.25 10 false ILL+ 5.865,0.51 6.073,0.708 0.208,0.198 10 false 14 1.344,5.604 1.885,5.771 0.542,0.167 10 false RH Side 1.396,3.385 1.938,3.552 0.542,0.167 10 false LH Side 5.813,3.667 6.125,3.865 0.313,0.198 10 false F77 2.021,0.583 3.271,0.792 1.25,0.208 10 false from PANEL Fuse

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).

·

Inspect the fuse for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the multi-media module receiver assembly, steering pad switch assembly or others (hazard switch etc.) comes on when the light control switch is turned to the head or tail position.

Result
Result Proceed to
Illumination comes on for all components except steering pad switch assembly. A
Illumination comes on for all components except multi-media module receiver assembly. B
No illumination comes on (multi-media module receiver assembly, steering pad switch, hazard switch, heater control switch, etc.). C



A

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

B

6.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL CIRCUIT)

C

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.
U166088E02
2.219,1.323 2.521,1.625 false 0.115,0.042 0.333,0.24 0.219,0.198 10 false *a 2.344,1.667 2.656,1.865 0.313,0.198 10 false IL+2 1.552,0.219 1.865,0.385 0.313,0.167 10 false E12

Disconnect the spiral cable sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E12-12 (IL+2) - Body ground Light control switch in the tail or head position 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)



OK

3.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly (See page Steering>STEERING COLUMN>STEERING WHEEL>REMOVAL).


b.

Inspect the steering pad switch assembly (See page Steering>STEERING COLUMN>STEERING WHEEL>INSPECTION).



OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL).


b.

Inspect the spiral cable sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION).



OK

5.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA NODULE RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY AND BODY GROUND)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA NODULE RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY AND BODY GROUND)
a.

Disconnect the F77 multi-media module receiver assembly connector.


b.

Disconnect the E12 spiral cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-14 (ILL+) - E12-12 (IL+2) Always Below 1 Ω
F77-32 (SWG) - E12-4 (EAU) Always Below 1 Ω
F77-14 (ILL+) - Body ground Always 10 kΩ or higher
F77-32 (SWG) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL CIRCUIT)
a.
U165199E01
1.495,0.337 1.797,0.520 0.302,0.184 10 F77 2.412,1.749 2.739,1.905 0.327,0.156 10 ILL+ 2.56,1.722 2.553,1.722 2.553,1.722 2.374,1.092 false 0.198,0.13 0.381,0.335 0.184,0.205 10 *a

Disconnect the multi-media module receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F77-14 (ILL+) - Body ground Light control switch in the tail or head position 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Multi-media Module Receiver Assembly)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR