Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › from 2015.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255487 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Illumination Circuit  


DESCRIPTION

Power is supplied to the radio and display receiver assembly and steering pad switch assembly illumination when the headlight dimmer switch is in the tail or head position.

WIRING DIAGRAM

E335086E06
0.292,6.073 2.333,6.354 2.042,0.281 10 false Steering Pad Switch Assembly 6.021,0.833 6.396,1.01 0.375,0.177 10 false SWG 5.604,0.844 6,1.021 0.396,0.177 10 false F124 5.667,0.635 6,0.813 0.333,0.177 10 false 23 6.031,3.375 6.406,3.552 0.375,0.177 10 false ILL+ 4.24,2.083 5.052,2.563 0.813,0.479 10 false from PANEL NO.2 Fuse 5.604,3.427 5.938,3.604 0.333,0.177 10 false F120 5.656,3.198 5.99,3.375 0.333,0.177 10 false 10 3.698,5.365 4.167,5.542 0.469,0.177 10 false E122 3.823,5.125 4.063,5.302 0.24,0.177 10 false 2 3.688,3.417 4.156,3.594 0.469,0.177 10 false E122 3.76,3.188 4,3.365 0.24,0.177 10 false 13 3.688,0.854 4.167,1.031 0.479,0.177 10 false E122 3.813,0.656 4.052,0.833 0.24,0.177 10 false 3 2.688,5.354 3.021,5.531 0.333,0.177 10 false z37 2.771,5.146 3.01,5.323 0.24,0.177 10 false 4 2.688,3.417 3.021,3.594 0.333,0.177 10 false z73 2.76,3.188 3,3.365 0.24,0.177 10 false 5 2.688,0.865 3.021,1.042 0.333,0.177 10 false z73 2.771,0.615 3.01,0.792 0.24,0.177 10 false 8 6.021,3.927 6.479,4.104 0.458,0.177 10 false ILL- 5.594,3.948 5.927,4.125 0.333,0.177 10 false F122 5.719,3.719 6.052,3.896 0.333,0.177 10 false 5 2.917,6.031 3.927,6.458 1.01,0.427 10 false Spiral Cable Sub-assembly 5.75,4.417 7.031,4.865 1.281,0.448 10 false Radio and Display Receiver Assembly 0.333,5.594 2.25,5.865 1.917,0.271 10 false Steering Pad Switch RH Side 0.25,2.771 2.167,3.042 1.917,0.271 10 false Steering Pad Switch LH Side 3.177,5.281 3.635,5.531 0.458,0.25 10 false ECC 3.167,3.333 3.625,3.583 0.458,0.25 10 false IL+2 3.167,0.76 3.625,1.01 0.458,0.25 10 false EAU

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).

·

Inspect the fuse for circuits related to this system before performing the following inspection procedure.



HINT:

When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).


PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the radio and display receiver assembly, steering pad switch assembly or others (hazard switch etc.) comes on when the headlight dimmer switch is turned to the head or tail position.

Result
Result Proceed to
Illumination comes on for all components except steering pad switch assembly. A
Illumination comes on for all components except radio and display receiver assembly. B
No illumination comes on (radio and display receiver assembly, steering pad switch, hazard switch, heater control switch, etc.). C



A

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

B

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY)

C

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.
U166378E01
1.564,0.248 1.932,0.405 0.368,0.157 10 E122 2.559,1.65 2.905,1.801 0.347,0.150 10 IL+2 2.104,1.428 2.41,1.74 2.41,1.74 2.526,1.74 false

Disconnect the spiral cable sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E122-13 (IL+2) - Body ground Light control switch in the tail or head position 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)



OK

3.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly (See page Steering>STEERING COLUMN>STEERING WHEEL>INSPECTION).


b.

Inspect the steering pad switch assembly (See page Steering>STEERING COLUMN>STEERING WHEEL>REMOVAL).



OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL).


b.

Inspect the spiral cable sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION).



OK

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY AND BODY GROUND)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY AND BODY GROUND)
a.

Disconnect the F124 radio and display receiver assembly connectors.


b.

Disconnect the E122 spiral cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F124-23 (SWG) - E122-3 (EAU) Always Below 1 Ω
E122-2 (ECC) - Body ground Always Below 1 Ω
F124-23 (SWG) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY)
a.
U166600E01
0.078,0.006 0.387,0.224 0.309,0.218 10 *a 1.447,0.198 1.887,0.409 0.441,0.211 10 F120 2.902,1.75 3.326,1.948 0.424,0.198 10 ILL+ 2.302,1.381 2.611,1.847 false 2.611,1.847 2.851,1.847 false

Disconnect the radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F120-10 (ILL+) - Body ground Light control switch in the tail or head position 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


OK

7.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BODY GROUND)
a.

Disconnect the F122 radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F122-5 (ILL-) - Body ground Always Below 1 Ω




OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR