Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2015.08
RM2660E _56 Audio / Visual / Telematics _052829 NAVIGATION / MULTI INFO DISPLAY _0255494 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B15C2  Speed Signal Malfunction  


DESCRIPTION

The multi-media module receiver assembly receives a vehicle speed signal from the combination meter assembly and information from the navigation antenna assembly, and then adjusts the vehicle position on the map. The multi-media module receiver assembly stores this DTC when the difference between the speed information that the navigation antenna assembly receives and the SPD pulse received from the combination meter assembly becomes large.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective systems based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.



DTC Code DTC Detection Condition Trouble Area
B15C2 A difference between the GPS speed and SPD pulse is detected
·

Meter / gauge system

·

Multi-media module receiver assembly



WIRING DIAGRAM

E240105E80
5.021,1.792 5.615,1.958 0.594,0.167 10 false F77 5.021,2 6.333,2.417 1.313,0.417 10 false Multi-media Module Receiver Assembly 4.938,0.948 5.125,1.125 0.188,0.177 10 false 56 5.208,1.052 5.594,1.26 0.385,0.208 10 false SPD 1.781,1.063 1.979,1.24 0.198,0.177 10 false +S 2.063,0.938 2.281,1.167 0.219,0.229 10 false 6 0.781,1.781 1.146,1.969 0.365,0.188 10 false E119 0.781,1.969 2.74,2.198 1.958,0.229 10 false Combination Meter Assembly

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION).


PROCEDURE

2.CHECK DTC
a.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

NG

3.CHECK VEHICLE SENSOR (OPERATION CHECK)
3.CHECK VEHICLE SENSOR (OPERATION CHECK)
a.
E276610

Enter the "System Sensors Check" screen. Refer to Check GPS & Vehicle Sensors in Operation Check (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK).


b.

While driving the vehicle, compare the "Speed" indicator to the reading on the speedometer. Check if these readings are almost equal.

OK:

The readings are equal or almost equal.




OK

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY

NG

4.CHECK COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
4.CHECK COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
U166388E02
2.208,1.281 2.656,1.958 2.656,1.958 2.813,1.958 false 1.49,0.271 1.875,0.5 0.385,0.229 10 false E119 0.125,0.094 0.396,0.313 0.271,0.219 10 false *a 2.896,1.854 3.313,2.073 0.417,0.219 10 false +S 1.115,3.854 1.531,4.073 0.417,0.219 10 false A 2.813,3.583 3.167,3.802 0.354,0.219 10 false GND

Check the output waveform.

i.

Remove the combination meter assembly with the connector(s) still connected (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).


ii.

Connect an oscilloscope to terminal E119-6 (+S) and body ground.


iii.

Turn the engine switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal E119-6 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.


Text in Illustration
*a Component with harness connected
(Combination Meter Assembly)




OK

5.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

5.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the F77 multi-media module receiver assembly connector.


b.

Disconnect the E119 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-56 (SPD) - E119-6 (+S) Always Below 1 Ω
F77-56 (SPD) - Body ground Always 10 kΩ or higher




OK

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR