Home › Power Source / Network › 1GR-FE (BATTERY / CHARGING) › CHARGING SYSTEM › 2014.08–2015.08
RM2660E _57 Power Source / Network _052832 1GR-FE BATTERY / CHARGING _0255519 CHARGING SYSTEM J

1GR-FE BATTERY / CHARGING  CHARGING SYSTEM  Noise Occurs from V-ribbed Belt or Generator Assembly  


PROCEDURE

1.CONFIRM PROBLEM SYMPTOM
a.

Confirm the problem symptom.

Result:
Symptom Proceed to
Noise occurs from fan and generator V belt A
Noise occurs from generator assembly B




A

2.CHECK FAN AND GENERATOR V BELT FOR WEAR

B

6.CHECK FOR NOISE WHEN ROTOR IS TURNING FREELY
2.CHECK FAN AND GENERATOR V BELT FOR WEAR
a.

Check the fan and generator V belt for wear or damage.

OK:

The fan and generator V belt is not worn or damaged.




OK

3.CHECK GENERATOR PULLEY WITH CLUTCH FOR WEAR

NG

REPLACE FAN AND GENERATOR V BELT

3.CHECK GENERATOR PULLEY WITH CLUTCH FOR WEAR
a.

Check the generator pulley with clutch grooves for wear or damage.

OK:

The generator pulley with clutch grooves are not worn or damaged.


Result:
The Result Proceed to
OK A
NG (Generator Assembly (for 100 A Type)) B
NG (Generator Assembly (for 130 A Type)) C




A

4.CHECK FOR NOISE WHILE CLUTCH PULLEY IS OPERATING

B

REPLACE GENERATOR PULLEY WITH CLUTCH (for 100 A Type)

C

REPLACE GENERATOR PULLEY WITH CLUTCH (for 130 A Type)

4.CHECK FOR NOISE WHILE CLUTCH PULLEY IS OPERATING
a.

Start the engine and check the generator pulley with clutch for looseness.

OK:

The generator pulley with clutch is not loose.




OK

5.INSPECT GENERATOR PULLEY WITH CLUTCH (UNIT INSPECTION)

NG

TIGHTEN GENERATOR PULLEY WITH CLUTCH TO SPECIFIED TORQUE

5.INSPECT GENERATOR PULLEY WITH CLUTCH (UNIT INSPECTION)

b.

Check the installation condition of the generator pulley cap.

OK:

The generator pulley cap is not loose or missing.



c.

Check for grease leaks (for wet pulley) or particle formation due to friction (for dry pulley).

OK:

No grease leaks (for wet pulley) or large build-up of particles (for dry pulley).



d.

Check the generator pulley with clutch for misalignment (interference with the generator assembly).

OK:

The generator pulley with clutch is correctly aligned (no interference with the generator assembly).



e.
A288972

Turn the generator pulley with clutch clockwise and counterclockwise by hand and check for noise.

OK:

Noise does not occur when turned in both directions.



f.

Turn the generator pulley with clutch clockwise and counterclockwise by hand and visually check for runout.

OK:

The generator pulley with clutch does not have runout.



g.
A288971

Using a screwdriver, hold the fan of the generator rotor assembly located inside the generator assembly in place and check that the generator pulley with clutch locks when turned clockwise and turns freely when turned counterclockwise.

OK:

The generator pulley with clutch locks when turned clockwise and turns freely when turned counterclockwise.


Result:
The Result Proceed to
OK A
NG (Generator Assembly (for 100 A Type)) B
NG (Generator Assembly (for 130 A Type)) C




A

INSPECT PULLEY OTHER THAN GENERATOR ASSEMBLY PULLEY

B

REPLACE GENERATOR PULLEY WITH CLUTCH (for 100 A Type)

C

REPLACE GENERATOR PULLEY WITH CLUTCH (for 130 A Type)

6.CHECK FOR NOISE WHEN ROTOR IS TURNING FREELY
a.

Perform a road test and check that noise does not occur when decelerating.

OK:

Noise does not occur.



b.

Turn the engine off and check that no noise is produced by the generator pulley with clutch as the engine stops.

OK:

Noise does not occur.


Result:
The Result Proceed to
OK A
NG (Generator Assembly (for 100 A Type)) B
NG (Generator Assembly (for 130 A Type)) C




A

7.CHECK ENGAGEMENT OF GENERATOR PULLEY WITH CLUTCH

B

REPLACE GENERATOR PULLEY WITH CLUTCH (for 100 A Type)

C

REPLACE GENERATOR PULLEY WITH CLUTCH (for 130 A Type)

7.CHECK ENGAGEMENT OF GENERATOR PULLEY WITH CLUTCH

b.
A288971

Using a screwdriver, hold the fan in the generator rotor assembly located inside the generator assembly in place and check that the generator pulley with clutch locks when turned clockwise (locking direction).

OK:

The generator pulley with clutch locks.


Result:
The Result Proceed to
OK (Generator Assembly (for 100 A Type)) A
OK (Generator Assembly (for 130 A Type)) B
NG (Generator Assembly (for 100 A Type)) C
NG (Generator Assembly (for 130 A Type)) D




A

REPAIR OR REPLACE GENERATOR ASSEMBLY (for 100 A Type)

B

REPAIR OR REPLACE GENERATOR ASSEMBLY (for 130 A Type)

C

REPLACE GENERATOR PULLEY WITH CLUTCH (for 100 A Type)

D

REPLACE GENERATOR PULLEY WITH CLUTCH (for 130 A Type)