Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255535 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B1249  Double Locking ECU Communication Stop  


DESCRIPTION

DTC B1249 is stored when communication between the double lock door control relay assembly and main body ECU (multiplex network body ECU) stops for more than 10 seconds.

DTC Code DTC Detection Condition Trouble Area
B1249 No communication from the double door lock relay assembly for more than 10 seconds.
·

Double lock door control relay assembly

·

Main body ECU (multiplex network body ECU)

·

Cowl side junction block LH

·

Harness or connector



WIRING DIAGRAM

E340192E01
1.212,0.874 2.055,1.042 0.843,0.168 10 from Battery 1.198,1.565 2.041,1.733 0.843,0.168 10 from Battery 2.666,1.145 3.641,1.292 0.975,0.147 10 MPX-B NO.1 2.679,1.813 4.147,1.959 1.468,0.147 10 DOOR DBL/L 0.433,4.784 1.497,4.942 1.063,0.158 10 A 0.433,4.959 2.175,5.483 1.742,0.524 10 Main Body ECU (Multiplex Network Body ECU) 1.872,3.626 2.935,3.784 1.063,0.158 10 2J 1.872,3.801 3.808,4.325 1.936,0.524 10 Cowl Side Junction Block LH 5.519,0.905 5.983,1.078 0.464,0.172 10 CPUB 5.5,3.046 5.964,3.218 0.464,0.172 10 MPX1 5.519,5.078 5.918,5.250 0.399,0.172 10 GND 5.528,1.606 5.760,1.778 0.231,0.172 10 +B 1.365,3.058 1.706,3.214 0.341,0.156 10 LIN2 1.799,2.92 2.140,3.076 0.341,0.156 10 16 3.718,2.92 4.059,3.076 0.341,0.156 10 13 5.043,5.926 6.717,6.274 1.675,0.348 10 Double Lock Door Control Relay Assembly 5.2,0.793 5.738,0.965 0.538,0.172 10 11 5.272,2.906 5.735,3.078 0.464,0.172 10 9 5.277,4.956 5.676,5.128 0.399,0.172 10 7 5.209,1.493 5.477,1.665 0.268,0.172 10 12 5.042,5.746 5.692,5.935 0.650,0.189 10 E167 0.551,6.387 2.216,6.571 1.665,0.184 10 : LIN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off to troubleshoot:

Connect the GTS to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

DTC B2325 is output when the communication between all of the following components and main body ECU (multiplex network body ECU) stops.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Recheck for DTC (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1249 is output A
DTC B1249 is not output B



A

3.CHECK HARNESS AND CONNECTOR (DOUBLE LOCK CONTROL RELAY ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU]

B

3.CHECK HARNESS AND CONNECTOR (DOUBLE LOCK CONTROL RELAY ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU]
a.

Disconnect the A main body ECU connector.


b.

Disconnect the E167 double lock control relay connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-16 (LIN2) - E167-9 (MPX1) Always Below 1 Ω
A-16 (LIN2) or E167-9 (MPX1) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY VOLTAGE AND BODY GROUND)

NG

7.CHECK HARNESS AND CONNECTOR (DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY - COWL SIDE JUNCTION BLOCK LH
4.CHECK HARNESS AND CONNECTOR (DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY VOLTAGE AND BODY GROUND)
a.
U166647E01
1.509,0.16 1.910,0.436 0.401,0.276 10 E167 2.808,0.541 3.209,0.713 0.401,0.172 10 GND 1.582,1.853 1.707,1.853 1.707,1.853 1.981,1.329 false 0.045,0 0.258,0.203 0.214,0.203 10 *a 2.652,1.779 2.886,1.958 0.234,0.179 10 +B 1.063,1.783 1.503,1.945 0.439,0.162 10 CPUB 2.754,0.62 2.605,0.62 2.605,0.62 2.216,1.077 false 1.582,1.853 1.707,1.853 1.707,1.853 1.981,1.329 false 2.57,1.866 2.445,1.866 2.445,1.866 2.171,1.342 false 2.57,1.866 2.445,1.866 2.445,1.866 2.171,1.342 false

Disconnect the E167 double lock control relay connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E167-7 (GND) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
E167-11 (CPUB) - Body ground Always 11 to 14 V
E167-12 (+B) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Double Lock Door Control Relay Assembly)



OK

5.REPLACE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY
a.

Temporarily replace the double lock door control relay with a new or normally functioning one (See page Vehicle Interior>DOOR LOCK>DOOR CONTROL RELAY (for LHD)>REMOVAL)*1, (See page Vehicle Interior>DOOR LOCK>DOOR CONTROL RELAY (for RHD)>REMOVAL)*2.

*1: for LHD

*2: for RHD





NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1249 is not output A
DTC B1249 is output (for LHD) B
DTC B1249 is output (for RHD) C



A

END (DOUBLE LOCK DOOR CONTROL RELAY IS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

7.CHECK HARNESS AND CONNECTOR (DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY - COWL SIDE JUNCTION BLOCK LH
a.

Disconnect the 2J cowl side junction block LH connector.


b.

Disconnect the E167 double lock door control relay connector.


c.

Measure the resistance according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
2J-13 - E167-9 (MPX1) Always Below 1 Ω
2J-13 or E167-9 (MPX1) - Body ground Always 10 kΩ or higher


Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR