Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255535 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2325  LIN Communication Bus Malfunction  


DESCRIPTION

The main body ECU (cowl side junction block LH) intermittently monitors the LIN communication bus between the components related to the door, double lock control relay*2 and sliding roof*1. DTC B2325 is stored when a malfunction in the LIN communication bus between the components related to the doors, double lock control relay*2 and sliding roof*1 is detected consecutively 3 times.

HINT:

*1: w/ Sliding Roof System

*2: w/ Double Locking System


DTC Code DTC Detection Condition Trouble Area
B2325 The main body ECU (cowl side junction block LH) detects a malfunction in the LIN communication bus between components related to the doors and sliding roof consecutively 3 times.
·

for Models with jam protection function on 4 windows

-

Master switch

-

Front power window regulator motor LH

-

Front power window regulator motor RH

-

Rear power window regulator motor LH

-

Rear power window regulator motor RH

-

Sliding roof ECU*1

-

Double lock door control relay*2

-

Main body ECU (cowl side junction block LH)

-

Harness or connector



·

for Models with jam protection function on driver door window only

-

Front power window regulator motor LH (for LHD)

-

Front power window regulator motor RH (for RHD)

-

Double lock door control relay*2

-

Main body ECU (cowl side junction block LH)

-

Harness or connector




WIRING DIAGRAM

E160479E04
1.55,1.216 1.760,1.388 0.209,0.172 10 E3 2.273,0.784 2.628,0.956 0.355,0.172 10 LIN2 2.361,2.466 2.636,2.638 0.275,0.172 10 LIN 4.593,2.466 4.868,2.638 0.275,0.172 10 LIN 4.608,0.784 4.963,0.956 0.355,0.172 10 LIN1 4.34,0.672 4.547,0.844 0.207,0.172 10 17 2.687,0.672 2.894,0.844 0.207,0.172 10 10 2.703,2.362 2.840,2.534 0.137,0.172 10 9 4.412,2.362 4.549,2.534 0.137,0.172 10 9 2.361,4.243 2.636,4.415 0.275,0.172 10 LIN 4.593,4.243 4.868,4.415 0.275,0.172 10 LIN 2.703,4.139 2.840,4.311 0.137,0.172 10 9 4.412,4.139 4.549,4.311 0.137,0.172 10 9 4.593,6.066 5.014,6.239 0.421,0.172 10 MPX1 4.412,5.935 4.549,6.107 0.137,0.172 10 4 1.55,1.393 3.105,1.754 1.554,0.361 10 Main Body ECU (Cowl Side Junction Block LH) 4.521,1.244 5.688,1.416 1.167,0.172 10 I11*2 or I22*3 4.521,1.421 5.452,1.593 0.931,0.172 10 Master Switch 4.521,2.965 4.827,3.137 0.306,0.172 10 l4 4.521,3.157 6.484,3.494 1.964,0.338 10 Front Power Window Regulator Motor RH 1.532,2.965 1.838,3.137 0.306,0.172 10 I12 1.532,3.115 3.495,3.452 1.964,0.338 10 Front Power Window Regulator Motor LH 1.532,4.723 1.775,4.895 0.244,0.172 10 J11 0.38,7.398 2.151,7.570 1.772,0.172 10 *1: w/ Sliding Roof System 0.38,8.21 2.392,8.382 2.012,0.172 10 *4: w/ Double Locking System 0.38,7.669 1.103,7.841 0.723,0.172 10 *2: for LHD 0.38,7.94 1.137,8.112 0.758,0.172 10 *3: for RHD 0.948,8.481 1.627,8.653 0.679,0.172 10 : LIN Line 1.532,4.914 3.495,5.252 1.964,0.338 10 Rear Power Window Regulator Motor LH 2.218,6.047 2.632,6.219 0.414,0.172 10 MPX1 2.689,5.925 2.872,6.097 0.183,0.172 10 9 1.562,6.53 1.972,6.702 0.411,0.172 10 E86 1.562,6.707 2.766,7.065 1.204,0.357 10 Double Lock Door Control Relay*4 4.52,4.723 4.730,4.895 0.209,0.172 10 J4 4.521,4.9 6.484,5.238 1.964,0.338 10 Rear Power Window Regulator Motor RH 4.52,6.544 4.931,6.716 0.411,0.172 10 R5 4.521,6.721 5.776,6.926 1.255,0.204 10 Sliding Roof ECU*1 0.033,0.011 3.501,0.181 3.468,0.170 10 for Models with Jam Protection Function on 4 Windows:

E237261E01
1.525,1.344 1.734,1.516 0.209,0.172 10 E3 2.276,0.898 2.631,1.070 0.355,0.172 10 LIN2 2.349,2.874 2.624,3.046 0.275,0.172 10 LIN 4.581,2.874 4.857,3.046 0.275,0.172 10 LIN 2.661,0.786 2.868,0.958 0.207,0.172 10 10 2.691,2.771 2.828,2.943 0.137,0.172 10 9 4.4,2.771 4.538,2.943 0.137,0.172 10 9 1.525,1.521 3.079,1.882 1.554,0.361 10 Main Body ECU (Cowl Side Junction Block LH) 4.509,3.373 4.815,3.545 0.306,0.172 10 l4 4.509,3.565 6.473,3.902 1.964,0.338 10 Front Power Window Regulator Motor RH*3 1.52,3.359 1.826,3.531 0.306,0.172 10 I12 1.52,3.537 3.484,3.874 1.964,0.338 10 Front Power Window Regulator Motor LH*2 0.144,4.35 2.156,4.522 2.012,0.172 10 *1: w/ Double Locking System 0.144,4.686 0.867,4.859 0.723,0.172 10 *2: for LHD 0.144,5.013 0.902,5.185 0.758,0.172 10 *3: for RHD 0.73,5.387 1.409,5.559 0.679,0.172 10 : LIN Line 4.569,0.898 4.983,1.070 0.414,0.172 10 MPX1 4.396,0.776 4.579,0.948 0.183,0.172 10 9 4.516,1.381 4.926,1.553 0.411,0.172 10 E86 4.516,1.558 5.720,1.915 1.204,0.357 10 Double Lock Door Control Relay*1 0.068,0.027 4.455,0.210 4.387,0.184 10 for Models with Jam Protection Function on Driver Door Window Only:

CAUTION / NOTICE / HINT

NOTICE:

When using the intelligent tester with the ignition switch off to troubleshoot:

Connect the intelligent tester to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.


HINT:

When DTC B2325 and a LIN communication stop DTC are output simultaneously, first perform the troubleshooting for the LIN communication stop DTC. Then perform the troubleshooting for DTC B2325.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output (for Models with Jam Protection Function on 4 Windows) A
DTC B2325 is output (for Models with Jam Protection Function on Driver Door Window Only) B
DTC B2325 is not output C



A

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - MASTER SWITCH)

B

18.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT POWER WINDOW REGULATOR MOTOR)

C

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - MASTER SWITCH)
a.
U166057E01
2.548,1.844 2.376,1.844 2.376,1.844 2.09,1.764 false 2.713,4.232 2.515,4.232 2.515,4.232 1.93,4.105 false 0.091,0.072 2.511,0.464 2.420,0.392 10 Front view of wire harness connector: (to Main Body ECU) 0.103,2.381 2.523,2.773 2.420,0.392 10 Front view of wire harness connector: (to Master Switch) 0.316,3.694 0.560,3.862 0.244,0.168 10 I11 0.362,1.284 0.606,1.453 0.244,0.168 10 E3 2.585,1.784 3.024,1.952 0.439,0.168 10 LIN2 2.766,4.103 3.205,4.271 0.439,0.168 10 LIN1 0.607,3.586 0.851,3.754 0.244,0.168 10 *1 0.051,4.048 0.772,4.194 0.721,0.146 10 *1: for LHD 0.051,4.354 0.789,4.500 0.739,0.146 10 *2: for RHD 2.595,3.676 2.839,3.844 0.244,0.168 10 I22 2.891,3.554 3.135,3.722 0.244,0.168 10 *2

Disconnect the E3 ECU connector.


b.

Disconnect the I11*1 or I22*2 switch connector.

HINT:

*1: for LHD

*2: for RHD



c.

Measure the resistance and voltage according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
E3-10 (LIN2) - I11-17 (LIN1)*1 or I22-17 (LIN1)*2 Always Below 1 Ω
E3-10 (LIN2) - Body ground Always 10 kΩ or higher


Standard Voltage:
Tester Connection Condition Specified Condition
E3-10 (LIN2) - Body ground Always Below 1 V




OK

4.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CLEAR DTC
a.

Reconnect the E3 ECU connector.


b.

Disconnect the I11*1 or I22*2 switch connector.

HINT:

*1: for LHD

*2: for RHD





NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

6.CLEAR DTC

B

REPLACE MASTER SWITCH

6.CLEAR DTC
a.

Reconnect the I11*1 or I22*2 switch connector.

HINT:

*1: for LHD

*2: for RHD



b.

Disconnect the I12 motor connector.




NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

8.CLEAR DTC

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR LH

8.CLEAR DTC
a.

Reconnect the I12 motor connector.


b.

Disconnect the I4 motor connector.




NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

10.CLEAR DTC

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR RH

10.CLEAR DTC
a.

Reconnect the I4 motor connector.


b.

Disconnect the J4 motor connector.




NEXT

11.CHECK FOR DTC
11.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

12.CLEAR DTC

B

REPLACE REAR POWER WINDOW REGULATOR MOTOR LH

12.CLEAR DTC
a.

Reconnect the J4 motor connector.


b.

Disconnect the J11 motor connector.




NEXT

13.CHECK FOR DTC
13.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output (w/ Double Locking System) A
DTC B2325 is output (w/o Double Locking System, w/ Sliding Roof System) B
DTC B2325 is output (w/o Double Locking System, w/o Sliding Roof System) C
DTC B2325 is not output D



A

14.CLEAR DTC

B

16.CLEAR DTC

C

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

D

REPLACE REAR POWER WINDOW REGULATOR MOTOR RH

14.CLEAR DTC
a.

Reconnect the J11 motor connector.


b.

Disconnect the E86 relay connector.




NEXT

15.CHECK FOR DTC
15.CHECK FOR DTC
a.

Recheck for DTC (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output (w/ Sliding Roof System) A
DTC B2325 is output (w/o Sliding Roof System) B
DTC B2325 is not output (for LHD) C
DTC B2325 is not output (for RHD) D



A

16.CLEAR DTC

B

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

C

REPLACE DOUBLE LOCK DOOR CONTROL RELAY

D

REPLACE DOUBLE LOCK DOOR CONTROL RELAY

16.CLEAR DTC
a.

Reconnect the E86 relay connector.


b.

Disconnect the R5 ECU connector.




NEXT

17.CHECK FOR DTC
17.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

B

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

18.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT POWER WINDOW REGULATOR MOTOR)
a.
U165869E03
2.448,4.344 2.219,4.344 2.219,4.344 1.76,3.958 false 2.49,1.646 2.323,1.646 2.323,1.646 2.031,1.573 false 0.042,0.042 2.344,0.479 2.302,0.438 10 false Front view of wire harness connector: (to Main Body ECU) 0.042,2.094 2.646,2.635 2.604,0.542 10 false Front view of wire harness connector: (to Front Power Window Regulator Motor LH*1, RH*2) 0.51,1.271 0.74,1.469 0.229,0.198 10 false E3 0.417,3.24 0.646,3.438 0.229,0.198 10 false I12 0.667,3.083 0.896,3.281 0.229,0.198 10 false *1 0.073,3.885 0.99,4.083 0.917,0.198 10 false *1: for LHD 0.073,4.229 0.99,4.427 0.917,0.198 10 false *2: for RHD 2.5,3.24 2.729,3.438 0.229,0.198 10 false I4 2.49,4.25 2.958,4.448 0.469,0.198 10 false LIN 2.729,3.083 2.958,3.281 0.229,0.198 10 false *2 2.521,1.563 2.979,1.76 0.458,0.198 10 false LIN2

Disconnect the E3 ECU connector.


b.

Disconnect the I12*1 or I4*2 motor connector.

HINT:

*1: for LHD

*2: for RHD



c.

Measure the resistance and voltage according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
E3-10 (LIN2) - I12-9 (LIN)*1 or I4-9 (LIN)*2 Always Below 1 Ω




OK

19.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CLEAR DTC
a.

Reconnect the E3 ECU connector.


b.

Disconnect the I12*1 or I4*2 motor connector.

HINT:

*1: for LHD

*2: for RHD





NEXT

20.CHECK FOR DTC
20.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output (for LHD) B
DTC B2325 is not output (for RHD) C



A

21.CLEAR DTC

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR LH

C

REPLACE FRONT POWER WINDOW REGULATOR MOTOR RH

21.CLEAR DTC
a.

Reconnect the I12*1 or I4*2 motor connector.

HINT:

*1: for LHD

*2: for RHD



b.

Disconnect the E86 relay connector.




NEXT

22.CHECK FOR DTC
22.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output (for LHD) B
DTC B2325 is not output (for RHD) C



A

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

B

REPLACE DOUBLE LOCK DOOR CONTROL RELAY

C

REPLACE DOUBLE LOCK DOOR CONTROL RELAY