Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255535 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2321  Driver Side Door ECU Communication Stop  


DESCRIPTION

*1: for LHD

*2: for RHD


This DTC is stored when LIN communication between the front power window regulator motor LH*1 (RH*2) and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC Code DTC Detection Condition Trouble Area
B2321 No communication between the front power window regulator motor LH*1 or RH*2 and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Front power window regulator motor LH*1

·

Front power window regulator motor RH*2

·

Main body ECU (multiplex network body ECU)

·

Cowl side junction block LH

·

Harness or connector



WIRING DIAGRAM

E340193E01
3.85,1.62 4.014,1.802 0.164,0.181 10 2J 5.87,0.967 6.181,1.148 0.310,0.181 10 LIN2 3.671,3.787 3.904,3.969 0.233,0.181 10 LIN 3.671,4.338 3.827,4.520 0.156,0.181 10 B 4.287,3.801 4.613,3.983 0.326,0.181 10 GND 5.534,0.808 5.706,0.989 0.171,0.181 10 16 3.659,0.817 3.831,0.998 0.171,0.181 10 13 3.409,3.643 3.565,3.824 0.156,0.181 10 9 4.777,3.675 4.933,3.857 0.156,0.181 10 1 3.4,4.203 3.555,4.384 0.156,0.181 10 2 2.355,4.94 3.616,5.121 1.261,0.181 10 I12*1, I4*2 5.667,2.908 6.852,3.490 1.185,0.582 10 Main Body ECU (Multiplex Network Body ECU) 2.348,5.136 5.885,5.514 3.537,0.378 10 Front Power Window Regulator Motor Assembly LH*1 or Front Power Window Regulator Motor Assembly RH*2 2.404,4.501 3.205,4.721 0.801,0.221 10 DOOR F/P 0.98,4.309 1.845,4.576 0.865,0.267 10 from Battery 0.601,6.345 2.791,6.524 2.189,0.179 10 : LIN Communication Line 3.85,1.779 5.643,1.960 1.793,0.181 10 Cowl Side Junction Block LH 5.665,2.731 5.991,2.912 0.326,0.181 10 A 0.158,5.727 1.419,5.908 1.261,0.181 10 *1: for LHD 0.158,6.007 1.419,6.188 1.261,0.181 10 *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off to troubleshoot:

Connect the GTS to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure



HINT:

DTC B2325 is stored when the communication between the front power window regulator motor and main body ECU (multiplex network body ECU) stops.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2321 is output A
DTC B2321 is not output B



A

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY

B

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY
a.

Disconnect the A main body ECU connector.


b.

Disconnect the I12*1 or I4*2 motor connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A-16 (LIN2) - I12-9 (LIN) Always Below 1 Ω
A-16 (LIN2) or I12-9 (LIN) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
A-16 (LIN2) - I4-9 (LIN) Always Below 1 Ω
A-16 (LIN2) or I4-9 (LIN) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY BATTERY AND BODY GROUND)

NG

7.CHECK HARNESS AND CONNECTOR (COWL SIDE JUNCTION BLOCK LH - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY BATTERY AND BODY GROUND)
a.
U163869E01
0.083,0.039 0.364,0.237 0.281,0.198 10 *a 0.428,0.62 0.723,0.782 0.295,0.163 10 I12 0.792,0.508 1.087,0.671 0.295,0.163 10 *A 0.48,1.058 0.775,1.221 0.295,0.163 10 I4 0.781,0.947 1.076,1.110 0.295,0.163 10 *B 0.495,1.516 0.843,1.678 0.348,0.163 10 GND 2.604,1.102 2.781,1.264 0.177,0.163 10 B 1.548,0.989 0.951,1.573 false 1.909,0.985 2.58,1.152 false

Disconnect the I12*1 or I4*2 front power window regulator motor connector.

*1: for LHD

*2: for RHD



b.

Measure the resistance and voltage according to the value(s) in the tables below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
I12-1 (GND) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
I4-1 (GND) - Body ground Always Below 1 Ω


Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
I12-2 (B) - Body ground Always 11 to 14 V

for RHD
Tester Connection Condition Specified Condition
I4-2 (B) - Body ground Always 11 to 14 V


Text in Illustration
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Front Power Window Regulator Motor)



OK

5.REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY
a.

Temporarily replace the front power window regulator motor LH*1 or RH*2 with a new or normally functioning one (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for Front Door)>REMOVAL).

*1: for LHD

*2: for RHD





NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2321 is not output A
DTC B2321 is output (for LHD) B
DTC B2321 is output (for RHD) C



A

END (FRONT POWER WINDOW REGULATOR MOTOR IS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

7.CHECK HARNESS AND CONNECTOR (COWL SIDE JUNCTION BLOCK LH - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY)
a.

Disconnect the 2J cowl side junction block LH connector.


b.

Disconnect the I12*1 or I4*2 front power window regulator motor connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the tables below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
2J-13 - I12-9 (LIN) Always Below 1 Ω
2J-13 or I12-9 (LIN) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
2J-13 - I4-9 (LIN) Always Below 1 Ω
2J-13 or I4-9 (LIN) - Body ground Always 10 kΩ or higher


Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR