Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255535 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2323  Rear Door RH ECU Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the rear power window regulator motor RH and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC Code DTC Detection Condition Trouble Area
B2323 No communication between the rear power window regulator motor RH and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Rear power window regulator motor assembly RH

·

Main body ECU (multiplex network body ECU)

·

Cowl side junction block LH

·

Harness or connector



WIRING DIAGRAM

E340193E03
0.593,6.352 2.208,6.533 1.615,0.181 10 : LIN Communication Line 4.292,3.804 4.617,3.985 0.326,0.181 10 GND 3.671,3.776 3.981,3.957 0.310,0.181 10 LIN 3.883,1.6 4.047,1.781 0.164,0.181 10 2J 3.657,4.327 3.813,4.508 0.156,0.181 10 B 5.856,0.983 6.167,1.165 0.310,0.181 10 LIN2 5.548,0.824 5.720,1.006 0.171,0.181 10 16 3.641,0.824 3.812,1.006 0.171,0.181 10 13 3.429,3.636 3.585,3.817 0.156,0.181 10 9 4.742,3.692 4.898,3.873 0.156,0.181 10 1 3.429,4.196 3.585,4.378 0.156,0.181 10 2 2.634,4.834 2.852,5.015 0.218,0.181 10 J4 5.692,2.845 6.865,3.427 1.173,0.582 10 Main Body ECU (Multiplex Network Body ECU) 0.954,4.305 2.032,4.572 1.078,0.267 10 from Battery 2.369,4.48 3.401,4.747 1.032,0.267 10 DOOR R/R 2.634,5.001 5.918,5.221 3.284,0.221 10 Rear Power Window Regulator Motor Assembly RH 3.883,1.758 5.675,1.940 1.793,0.181 10 Cowl Side Junction Block LH 5.686,2.701 6.011,2.882 0.326,0.181 10 A

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off to troubleshoot:

Connect the GTS to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

DTC B2325 is stored when the communication between the rear power window regulator motor and main body ECU (multiplex network body ECU) stops.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2323 is output A
DTC B2323 is not output B



A

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

B

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
a.

Disconnect the A main body ECU connector.


b.

Disconnect the J4 motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-16 (LIN2) - J4-9 (LIN) Always Below 1 Ω
A-16 (LIN2) or J4-9 (LIN) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH BATTERY AND BODY GROUND)

NG

7.CHECK HARNESS AND CONNECTOR (COWL SIDE JUNCTION BLOCK LH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
4.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH BATTERY AND BODY GROUND)
a.
U163871E01
0.07,0.033 0.337,0.211 0.268,0.179 10 *a 0.635,0.843 0.867,1.006 0.232,0.163 10 J4 0.566,1.401 0.916,1.564 0.351,0.163 10 GND 2.595,1.191 2.771,1.354 0.177,0.163 10 B 1.548,1.023 1.046,1.444 false 1.927,0.996 2.511,1.279 false

Disconnect the J4 motor connector.


b.

Measure the resistance and voltage according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
J4-1 (GND) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
J4-2 (B) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Rear Power Window Regulator Motor RH)



OK

5.REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
a.

Temporarily replace the rear power window regulator motor RH with a new or normally functioning one (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for Rear Door)>REMOVAL).




NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2323 is not output A
DTC B2323 is output (for LHD) B
DTC B2323 is output (for RHD) C



A

END (REAR POWER WINDOW REGULATOR MOTOR RH IS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

7.CHECK HARNESS AND CONNECTOR (COWL SIDE JUNCTION BLOCK LH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
a.

Disconnect the 2J cowl side junction block LH connector.


b.

Disconnect the J4 motor connector.


c.

Measure the resistance according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
2J-13 - J4-9 (LIN) Always Below 1 Ω
2J-13 or J4-9 (LIN) - Body ground Always 10 kΩ or higher


Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR