Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM › from 2015.08
RM2660E _58 Vehicle Interior _052838 DOOR LOCK _0255549 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  All Doors LOCK/UNLOCK Functions do not Operate Via Door Control Switch  


DESCRIPTION

The main body ECU receives switch signals from the door control switch assembly on the front passenger door and activates the door lock motor on each door according to these signals.

WIRING DIAGRAM

B375833E09
5.75,0.76 6.063,0.958 0.313,0.198 10 false L1 5.771,1.292 6.167,1.5 0.396,0.208 10 false UL1 5.479,0.635 5.792,0.833 0.313,0.198 10 false 20 5.479,1.177 5.792,1.375 0.313,0.198 10 false 22 2.604,0.635 2.917,0.833 0.313,0.198 10 false L 2.521,1.177 2.833,1.375 0.313,0.198 10 false UL 2.833,0.635 3.146,0.833 0.313,0.198 10 false 4 2.833,1.177 3.146,1.375 0.313,0.198 10 false 2 1.292,1.177 1.604,1.375 0.313,0.198 10 false E 1.094,1.177 1.406,1.375 0.313,0.198 10 false 3 1.104,1.719 1.417,1.917 0.313,0.198 10 false I33 1.094,1.896 3.333,2.198 2.24,0.302 10 false Door Control Switch Assembly 5.438,2.573 5.75,2.771 0.313,0.198 10 false A 5.49,2.771 6.729,3.156 1.24,0.385 10 false Main Body ECU 4.146,0.635 4.458,0.833 0.313,0.198 10 false 26 4.156,1.177 4.469,1.375 0.313,0.198 10 false 21 3.833,1.865 5.594,2.281 1.76,0.417 10 false Cowl Side Junction Block LH 3.844,1.708 4.156,1.906 0.313,0.198 10 false 2J

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Access. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

If the main body ECU (cowl side junction block LH) is replaced, refer to the Entry and Start System (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION).



PROCEDURE

1.READ VALUE USING GTS (DOOR CONTROL SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Front Right Door
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Door Lock SW Power window regulator switch assembly (door control switch) lock signal OFF or ON ON: Lock side of power window regulator switch assembly pushed
OFF: Lock side of power window regulator switch assembly not pushed
-
Door Unlock SW Power window regulator switch assembly (door control switch) unlock signal OFF or ON ON: Unlock side of power window regulator switch assembly pushed
OFF: Unlock side of power window regulator switch assembly not pushed
-

OK:

The GTS indicates ON or OFF according to the switch operation shown in the table.




OK

NG

2.INSPECT DOOR CONTROL SWITCH ASSEMBLY
2.INSPECT DOOR CONTROL SWITCH ASSEMBLY
a.

Remove the door control switch assembly (See pageVehicle Interior>DOOR LOCK>DOOR CONTROL SWITCH>REMOVAL).


b.

Inspect the door control switch assembly (See pageVehicle Interior>DOOR LOCK>DOOR CONTROL SWITCH>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (DOOR CONTROL SWITCH ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)

NG

REPLACE DOOR CONTROL SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (DOOR CONTROL SWITCH ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)
a.

Disconnect the I33 door control switch assembly connector.


b.

Disconnect the 2J instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2J-26 - I33-4 (L) Always Below 1 Ω
2J-21 - I33-2 (UL) Always Below 1 Ω
I33-3 (E) - Body ground Always Below 1 Ω
2J-26 or I33-4 (L) - Body ground Always 10 kΩ or higher
2J-21 or I33-2 (UL) - Body ground Always 10 kΩ or higher




OK

4.CHECK COWL SIDE JUNCTION BLOCK LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK COWL SIDE JUNCTION BLOCK LH

b.

Remove the main body ECU from the cowl side junction block LH.

U156855E04
2.479,1.969 2.198,2.438 2.198,2.438 2.021,2.438 false 2.677,1.969 2.833,2.427 2.833,2.427 3.01,2.427 false 2.063,0.927 2.24,1.125 0.177,0.198 10 false A 5.531,0.927 5.74,1.125 0.208,0.198 10 false 2J 1.844,2.365 2.198,2.604 0.354,0.24 10 false L1 3.031,2.333 3.385,2.573 0.354,0.24 10 false UL1 0.146,0 0.323,0.198 0.177,0.198 10 false *a

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2J-26 - A-20 (L1) Always Below 1 Ω
2J-21 - A-22 (UL1) Always Below 1 Ω




OK

NG