Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Start Function) › from 2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255570 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2274  ACC Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction in the ACC output circuit is detected. The ACC output circuit is the circuit that goes from the ACC output terminal of the certification ECU (smart key ECU assembly) to the ACC relay.

HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2274 Malfunction in the ACC relay circuit in the certification ECU (smart key ECU assembly) or in the external circuit (1-trip detection logic*).
HINT:

When the voltage at terminal ACCD is not at the standard, the system is determined to be malfunctioning.


·

AM2 fuse

·

ACC relay (cowl side junction block LH)

·

Certification ECU (smart key ECU assembly)

·

Harness or connector


Wait 10 seconds after turning the engine switch on (ACC) or on (IG), and then wait another 10 seconds after turning the engine switch off.

*: Only detected while a malfunction is present.


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
·

If there is a malfunction due to the relay being stuck on, the ACC relay does not turn off even though the engine switch is off.

·

If there is a malfunction due to the relay being stuck off, the ACC relay does not turn on even though the engine switch is on (ACC).


HINT:

The engine switch can be turned on (IG) and the engine can be started.


-

Related Data List and Active Test Items
DTC Data List Item Active Test Item
B2274
Power Source Control
·

ACC Relay Monitor


Starting Control
·

Ignition


-

WIRING DIAGRAM

C348651E06
4.865,2.042 5.323,2.198 0.458,0.156 10 false ACC 4.052,1.76 4.844,1.917 0.792,0.156 10 false 2J 3.083,1.635 3.563,1.823 0.479,0.188 10 false ACCD 3.146,1.26 3.938,1.417 0.792,0.156 10 false +B 3.563,1.635 3.781,1.792 0.219,0.156 10 false 9 2.563,1.688 2.833,1.865 0.271,0.177 10 false IC 2.417,2.177 2.667,2.333 0.25,0.156 10 false E 2.167,2.146 2.417,2.302 0.25,0.156 10 false 11 2.417,1.021 2.667,1.177 0.25,0.156 10 false +B 2.167,0.99 2.417,1.146 0.25,0.156 10 false 10 1.573,1.208 2.292,1.365 0.719,0.156 10 false AM2 4.052,1.573 4.844,1.729 0.792,0.156 10 false 18 4.042,1.333 4.833,1.49 0.792,0.156 10 false 2G 4.094,1.156 4.885,1.313 0.792,0.156 10 false 1 4.458,2.458 6.51,2.615 2.052,0.156 10 false Cowl Side Junction Block LH 5.573,1.448 6.385,1.604 0.813,0.156 10 false ECU-ACC 6.552,1.333 7.052,1.49 0.5,0.156 10 false 2I 6.531,1.146 6.74,1.302 0.208,0.156 10 false 51 6.542,1.75 7.042,1.906 0.5,0.156 10 false 2J 6.573,1.583 6.781,1.74 0.208,0.156 10 false 1 0.167,1.094 1,1.25 0.833,0.156 10 false from Battery 2.177,2.865 2.677,3.021 0.5,0.156 10 false E130 2.177,3.021 3.781,3.427 1.604,0.406 10 false Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus:

Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Start Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>PRECAUTION).

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

2.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS ORCONNECTOR IN CIRCUIT CONNECTED TOPOWER SOURCE

2.CHECK HARNESS AND CONNECTOR (GROUND)

OK

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - COWL SIDE JUNCTION BLOCK LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - COWL SIDE JUNCTION BLOCK LH)
a.

Disconnect the E130 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the 2J cowl side junction block LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E130-9 (ACCD) - 2J-18 Always Below 1 Ω
2J-1 - Body ground
E130-9 (ACCD) or 2J-18 - Body ground 10 kΩ or higher




OK

4.CHECK COWL SIDE JUNCTION BLOCK LH (ACC RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK COWL SIDE JUNCTION BLOCK LH (ACC RELAY)

b.

Measure the resistance according to the value(s) in the table below.

U156538E01
0.344,0.057 0.529,0.215 0.186,0.158 10 *a 3.148,1.964 3.562,2.123 0.413,0.158 10 2J 5.46,0.666 5.873,0.824 0.413,0.158 10 2I 5.796,1.992 6.209,2.151 0.413,0.158 10 2G

Text in Illustration
*a Component without harness connected
(Cowl Side Junction Block LH)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
2G-1 - 2I-51 Battery voltage not applied to terminals 2J-18 and 2J-1 10 kΩ or higher
Battery voltage applied to terminals 2J-18 and 2J-1 Below 1 Ω



Result
Result Proceed to
OK A
NG for LHD B
for RHD C


A

5.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

C

5.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the E130 certification ECU (smart key ECU assembly) connector.



c.
U165444E01
0.118,0.074 0.303,0.232 0.186,0.158 10 *a 0.219,1.549 0.716,1.708 0.497,0.158 10 ACCD 0.99,0.776 0.916,1.638 0.916,1.638 0.747,1.638 false 1.437,0.089 1.850,0.247 0.413,0.158 10 E130

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E130-9 (ACCD) - Body ground Engine switch off → Engine switch on (ACC) 1 V or less → 8.5 V or higher


Text in Illustration
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)