Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Start Function) › from 2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255570 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2285  Steering Lock Position Signal Circuit Malfunction  


DESCRIPTION

This DTC is stored when the steering lock position signal sent by the steering lock ECU (steering lock actuator assembly) via direct line and the steering lock position signal sent via LIN communication do not match.

HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2285 The steering lock position signal sent by the steering lock ECU (steering lock actuator assembly) via direct line and the steering lock position signal sent via LIN communication (1-trip detection logic*) do not match.
·

AM2 fuse

·

Steering lock ECU (steering lock actuator assembly)

·

Certification ECU (smart key ECU assembly)

·

Harness or connector


Disconnect the cable from the negative (-) battery terminal, wait 30 seconds and then reconnect the cable to the negative (-) battery terminal. Wait 40 seconds or more with the engine switch off (with the steering wheel locked), then turn the engine switch on (ACC) (with the steering unlocked) and wait 40 seconds or more.

*: Only detected while a malfunction is present and the engine switch is on (IG)


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The engine cannot be started. The ECU does not send an engine start request.

Related Data List and Active Test Items
DTC Data List Item Active Test Item
B2285
Power Source Control

Steering Unlock Switch


Entry&Start
·

Power Supply Short

·

Motor Driver Short

·

Lock Bar Stuck Error


-

WIRING DIAGRAM

C326204E05
1.885,1.375 2.333,1.573 0.448,0.198 10 false SLP1 2.354,1.375 2.51,1.573 0.156,0.198 10 false 4 2.573,0.74 3.448,0.969 0.875,0.229 10 false from Battery 4.052,0.885 4.823,1.083 0.771,0.198 10 false AM2 5.01,0.604 5.24,0.792 0.229,0.188 10 false 10 5.302,0.729 5.615,0.927 0.313,0.198 10 false +B 6.021,1.406 6.333,1.604 0.313,0.198 10 false IC 5.292,1.396 5.75,1.594 0.458,0.198 10 false SLP 5.021,1.385 5.333,1.583 0.313,0.198 10 false 23 5.021,2.271 5.333,2.469 0.313,0.198 10 false 11 5.292,2.396 5.448,2.594 0.156,0.198 10 false E 5.094,2.885 5.552,3.083 0.458,0.198 10 false E130 5.094,3.021 6.625,3.396 1.531,0.375 10 false Certification ECU (Smart Key ECU Assembly) 0.854,2.396 1.313,2.594 0.458,0.198 10 false E26 0.854,2.531 2.646,2.906 1.792,0.375 10 false Steering Lock ECU (Steering Lock Actuator Assembly) 0.542,3.344 2.188,3.531 1.646,0.188 10 false : LIN Communication Line 5.594,0.875 5.906,1.073 0.313,0.198 10 false +B 5.292,1.938 5.656,2.125 0.365,0.188 10 false LIN 2.042,1.917 2.406,2.104 0.365,0.188 10 false LIN 2.354,1.76 2.51,1.958 0.156,0.198 10 false 5 5.063,1.771 5.375,1.969 0.313,0.198 10 false 6

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus:

Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Before replacing the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) refer to the entry and start system (for Start Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>PRECAUTION).

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.CHECK FOR DTC (LIN COMMUNICATION SYSTEM)
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

LIN communication system DTC B2785 is not output simultaneously.


HINT:
·

If the steering wheel cannot be locked or unlocked, the engine switch cannot be turned on (IG) and the engine cannot be started.

·

If LIN communication is not available, the steering wheel cannot be locked or unlocked.





OK

2.READ VALUE USING GTS (STEERING UNLOCK SWITCH)

NG

2.READ VALUE USING GTS (STEERING UNLOCK SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

According to the display on the GTS, read the Data List.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Steering Unlock Switch State of steering unlock sensor signal output from steering lock actuator assembly/ON or OFF ON: Steering unlocked
OFF: Steering locked
·

When the shift lever is in P (for Automatic Transmission) and the engine switch is off, if any door is opened then closed, the steering is locked.

·

When the key is inside the vehicle and the engine switch is turned on (ACC) or on (IG), the steering unlocks.

·

The engine cannot be started when the steering unlock signal is off.



Result
Result Proceed to
Data List item does not change A
Data List item changes for Manual Tilt and Manual Telescopic Steering Column B
for Power Tilt and Power Telescopic Steering Column C



A

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

B

C

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

4.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

4.CHECK HARNESS AND CONNECTOR (GROUND)

OK

5.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
a.

Reconnect the E26 steering lock ECU (steering lock actuator assembly) connector.


b.

Reconnect the E130 certification ECU (smart key ECU assembly) connector.


c.
U156537E01
0.139,0.071 0.324,0.229 0.186,0.158 10 *a 2.481,1.723 2.978,1.882 0.497,0.158 10 SLP1 1.777,1.126 2.305,1.789 2.305,1.789 2.428,1.789 false 1.608,0.211 2.022,0.369 0.413,0.158 10 E26

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Positive (+) tester probe → E26-4 (SLP1)
Negative (-) tester probe → Body ground
Steering locked* 10 kΩ or higher
Steering unlocked* Below 1 Ω


HINT:
·

*: If any of the doors are opened then closed with the shift lever in P and the engine switch off, the steering wheel will be locked. If the engine switch is then turned on (ACC) or on (IG), the steering wheel will be unlocked.

·

DTC B2285 may be stored due to a malfunction in the steering lock ECU (steering lock actuator assembly). The steering lock position signal and unlock position signal are sent from the steering lock ECU (steering lock actuator assembly) to the certification ECU (smart key ECU assembly) individually.



Text in Illustration
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly))

Result
Result Proceed to
OK A
NG for Manual Tilt and Manual Telescopic Steering Column B
for Power Tilt and Power Telescopic Steering Column C



A

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY))

B

C

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY))
a.

Disconnect the E130 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the E26 steering lock ECU (steering lock actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E130-23 (SLP) - E26-4 (SLP1) Always Below 1 Ω
E130-23 (SLP) or E26-4 (SLP1) - Body ground 10 kΩ or higher




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR