Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM (w/ Entry and Start System) › from 2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255571 THEFT DETERRENT SYSTEM(w/ Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM(w/ Entry and Start System)  Glass Breakage Sensor Circuit  


DESCRIPTION

When the glass breakage sensor detects that the back door glass, quarter window glass LH or quarter window glass RH is tapped or broken, the sensor will set off the alarm for 30 seconds.

WIRING DIAGRAM

B605329E08
1.083,1.458 1.49,1.625 0.406,0.167 10 false SSR+ 1.104,2.021 1.49,2.177 0.385,0.156 10 false SSR- 1.604,1.375 1.719,1.542 0.115,0.167 10 false 2 1.604,1.938 1.719,2.094 0.115,0.156 10 false 1 1.083,3.927 1.49,4.094 0.406,0.167 10 false SSR+ 1.104,4.49 1.49,4.646 0.385,0.156 10 false SSR- 1.604,3.844 1.719,4.01 0.115,0.167 10 false 2 1.604,4.406 1.719,4.563 0.115,0.156 10 false 1 0.385,2.302 0.646,2.469 0.26,0.167 10 false L34 0.385,4.771 0.667,4.927 0.281,0.156 10 false K26 5.344,4.49 5.75,4.656 0.406,0.167 10 false SSR+ 5.073,4.333 5.188,4.5 0.115,0.167 10 false 1 5.208,5 6.802,5.646 1.594,0.646 10 false Back Window Glass (Glass Breakage Sensor) 5.01,4.5 5.344,4.698 0.333,0.198 10 false S37 5.354,1.302 5.938,1.542 0.583,0.24 10 false GPBS 5.115,1.354 5.292,1.521 0.177,0.167 10 false 7 5.313,2.479 6.896,3.219 1.583,0.74 10 false Main Body ECU (Multiplex Network Body ECU) 5.323,2.281 5.844,2.458 0.521,0.177 10 false E118 6.281,4.333 6.396,4.5 0.115,0.167 10 false 1 6.281,4.49 6.573,4.656 0.292,0.167 10 false B 6.042,4.49 6.167,4.656 0.125,0.167 10 false E 0.385,4.917 1.479,5.781 1.094,0.865 10 false Quarter Window Assembly LH (Glass Breakage Sensor) 0.385,2.5 1.698,3.292 1.313,0.792 10 false Quarter Window Assembly RH (Glass Breakage Sensor) 5.813,0.781 6.396,1.021 0.583,0.24 10 false +B

CAUTION / NOTICE / HINT

·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.

·

w/ Door Control Battery:

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION).


PROCEDURE

1.READ VALUE USING GTS (GLASS BREAK SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

According to the display on the GTS, read the Data List.


Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Glass break sensor detection Glass breakage sensor detection / With or Without1 With: Glass breakage sensor connected
Without: Glass breakage sensor not connected
-

OK:

"With" (glass breakage sensor operating) appears on GTS screen.


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C


OK

2.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG (for LHD)

REPLACE MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU]

NG (for RHD)

REPLACE MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU]

2.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.
B605675C04
1.49,0.271 1.938,0.49 0.448,0.219 1.094,1.802 1.354,1.802 1.354,1.802 1.625,1.281 true 1.604,0.302 2.063,0.5 0.458,0.198 10 false L34 0.667,1.729 1.438,1.938 0.771,0.208 10 false SSR+ 0.198,0.135 0.969,0.344 0.771,0.208 10 false *a
*a Front view of wire harness connector
(to Quarter Window Assembly RH (Glass Breakage Sensor))


Disconnect the quarter window assembly RH (glass breakage sensor) connector.


b.

Using an oscilloscope, check the waveform.

Standard Resistance:
Tester Connection Condition Tool Setting Specified Condition
L34-2 (SSR+) - body ground Always 2 V/DIV., 20 ms./DIV. Pulse generation




OK

3.CHECK QUARTER WINDOW ASSEMBLY RH (GLASS BREAKAGE SENSOR)

NG

8.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - QUARTER WINDOW ASSEMBLY RH (GLASS BREAKAGE SENSOR))
3.CHECK QUARTER WINDOW ASSEMBLY RH (GLASS BREAKAGE SENSOR)
a.
B605675C05
1.51,0.219 1.906,0.448 0.396,0.229 1.25,1.75 1.448,1.75 1.448,1.75 1.615,1.281 true 1.594,0.25 2.052,0.448 0.458,0.198 10 false K26 0.854,1.667 1.458,1.875 0.604,0.208 10 false SSR+ 0.167,0.115 0.771,0.323 0.604,0.208 10 false *a
*a Front view of wire harness connector
(to Quarter Window Assembly LH (Glass Breakage Sensor))


Disconnect the quarter window assembly LH (glass breakage sensor) connector.


b.

Using an oscilloscope, check the waveform.

Standard Resistance:
Tester Connection Condition Tool Setting Specified Condition
K26-2 (SSR+) - body ground Always 2 V/DIV., 20 ms./DIV. Pulse generation




OK

4.CHECK QUARTER WINDOW ASSEMBLY LH (GLASS BREAKAGE SENSOR)

NG

7.CHECK HARNESS AND CONNECTOR (QUARTER WINDOW ASSEMBLY RH (GLASS BREAKAGE SENSOR) - QUARTER WINDOW ASSEMBLY LH (GLASS BREAKAGE SENSOR))
4.CHECK QUARTER WINDOW ASSEMBLY LH (GLASS BREAKAGE SENSOR)
a.
B605531C08
1.479,0.396 1.896,0.635 0.417,0.24 1.24,1.719 1.427,1.719 1.427,1.719 1.594,1.167 true 1.563,0.438 2.021,0.635 0.458,0.198 10 false S37 0.167,0.177 0.625,0.375 0.458,0.198 10 false *a 0.813,1.635 1.271,1.833 0.458,0.198 10 false SSR+
*a Front view of wire harness connector
(to Back Window Glass (Glass Breakage Sensor))


Disconnect the back window glass (glass breakage sensor) connector.


b.

Using an oscilloscope, check the waveform.

Standard Resistance:
Tester Connection Condition Tool Setting Specified Condition
S37-1 (SSR+) - body ground Always 2 V/DIV., 20 ms./DIV. Pulse generation




OK

5.CHECK HARNESS AND CONNECTOR (BACK WINDOW GLASS (GLASS BREAKAGE SENSOR) - BODY GROUND)

NG

6.CHECK HARNESS AND CONNECTOR (QUARTER WINDOW ASSEMBLY LH (GLASS BREAKAGE SENSOR) - BACK WINDOW GLASS (GLASS BREAKAGE SENSOR))
5.CHECK HARNESS AND CONNECTOR (BACK WINDOW GLASS (GLASS BREAKAGE SENSOR) - BODY GROUND)
a.
B592595C04
1.615,0.479 2.01,0.708 0.396,0.229 1.427,1.854 1.615,1.854 1.615,1.854 1.76,1.292 true 1.75,0.51 2.292,1 0.542,0.49 10 false B 1.281,1.781 1.74,1.979 0.458,0.198 10 false E 0.198,0.156 0.656,0.354 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Back Window Glass (Glass Breakage Sensor))


Disconnect the back window glass (glass breakage sensor) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-1 (E) - Body ground Always Below 1 Ω




OK

REPLACE BACK WINDOW GLASS (GLASS BREAKAGE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (QUARTER WINDOW ASSEMBLY LH (GLASS BREAKAGE SENSOR) - BACK WINDOW GLASS (GLASS BREAKAGE SENSOR))
a.

Disconnect the K26 quarter window assembly LH (glass breakage sensor) connector.


b.

Disconnect the S37 back window glass (glass breakage sensor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K26-1 (SSR-) - S37-1 (SSR+) Always Below 1 Ω




OK

REPLACE QUARTER WINDOW ASSEMBLY LH (GLASS BREAKAGE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (QUARTER WINDOW ASSEMBLY RH (GLASS BREAKAGE SENSOR) - QUARTER WINDOW ASSEMBLY LH (GLASS BREAKAGE SENSOR))
a.

Disconnect the L34 quarter window assembly RH (glass breakage sensor) connector.


b.

Disconnect the K26 quarter window assembly LH (glass breakage sensor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L34-1 (SSR-) - K26-2 (SSR+) Always Below 1 Ω




OK

REPLACE QUARTER WINDOW ASSEMBLY RH (GLASS BREAKAGE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - QUARTER WINDOW ASSEMBLY RH (GLASS BREAKAGE SENSOR))
a.

Disconnect the L34 quarter window assembly RH (glass breakage sensor) connector.


b.

Disconnect the E118 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E118-7 (GPBS) - L34-2 (SSR+) Always Below 1 Ω



Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C


OK (for LHD)

REPLACE MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU]

OK (for RHD)

REPLACE MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU]

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR