Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM (w/ Entry and Start System) › 2015.08–2017.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255571 THEFT DETERRENT SYSTEM(w/ Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM(w/ Entry and Start System)  B276A  Short to GND in Tilt Sensor Signal Circuit  


DESCRIPTION

This DTC is stored when terminal CSIF of the theft warning tilt sensor (yaw rate sensor) has not received a signal for 5 seconds or more.


DTC Code DTC Detection Condition Trouble Area
B276A Terminal CSIF of theft warning tilt sensor (yaw rate sensor) has not received signal for 5 seconds or more
·

Theft warning tilt sensor (yaw rate sensor)

·

Main body ECU (multiplex network body ECU)

·

Harness or connector



WIRING DIAGRAM

B312497E22
5.635,1.729 6.104,2.01 0.469,0.281 10 false GCS 5.333,3.073 7,3.542 1.667,0.469 10 false Main Body ECU (Multiplex Network Body ECU) 5.323,2.917 5.771,3.125 0.448,0.208 10 false E117 3.51,1.729 3.896,1.927 0.385,0.198 10 false CSIF 1.844,2.646 2.135,2.875 0.292,0.229 10 false E50 1.844,2.833 3.521,3.26 1.677,0.427 10 false Theft Warning Tilt Sensor (Yaw Rate Sensor) 1.375,1.729 1.927,1.938 0.552,0.208 10 false GND 1.188,1.604 1.5,1.896 0.313,0.292 10 false 1 1.771,0.281 2.854,0.615 1.083,0.333 10 false from Battery 5.427,1.615 5.615,1.844 0.188,0.229 10 false 6 3.906,1.583 4.125,1.823 0.219,0.24 10 false 5 3.625,1.25 3.927,1.479 0.302,0.229 10 false +B 3.896,1.104 4.083,1.313 0.188,0.208 10 false 6 3.615,0.427 4.448,0.823 0.833,0.396 10 false J/B-B NO.2

CAUTION / NOTICE / HINT

NOTICE:
·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.

·

When replacing the theft warning tilt sensor (yaw rate sensor), perform zero point calibration (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>TILT SENSOR>REMOVAL).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

w/ Door Control Battery:

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>PRECAUTION).



PROCEDURE

1.CHECK THEFT WARNING TILT SENSOR (YAW RATE SENSOR) (CSIF)
a.

Using an oscilloscope, check the waveform.

U164280E01
1.683,0.122 1.857,0.296 0.174,0.174 10 *a 3.425,0.157 3.839,0.437 0.414,0.280 10 E117 4.868,1.803 5.459,1.977 0.591,0.174 10 GCS 1.625,2.666 1.799,2.840 0.174,0.174 10 *b 1.26,2.456 1.610,2.630 0.350,0.174 10 HI 1.26,2.909 1.652,3.083 0.392,0.174 10 LO 2.157,2.666 2.331,2.840 0.174,0.174 10 *c 3.974,2.634 4.148,2.808 0.174,0.174 10 *d 3.974,3.108 4.148,3.282 0.174,0.174 10 *e 2.101,3.183 2.275,3.357 0.174,0.174 10 *f 2.512,3.192 2.686,3.367 0.174,0.174 10 *g 2.654,3.538 2.829,3.712 0.174,0.174 10 *h 1.513,4.098 1.687,4.273 0.174,0.174 10 *i 3.95,4.098 4.125,4.273 0.174,0.174 10 *j 4.273,1.046 4.83,1.828 false 2.447,2.816 2.314,2.732 false 1.915,2.816 1.783,2.732 false

Text in Illustration
*a Component with harness connected
(Main body ECU [multiplex network body ECU])
*b CSIF Initial Signal
*c CSIF Initial Response *d Approximately 1.0 seconds
*e Initial Diagnosis *f Approximately 1.0 to 1.6 seconds
*g Approximately 0.05 seconds *h Approximately 5.5 seconds
*i Disarmed State *j Arming Preparation State

Measurement Condition
Tester Connection Content
Tester Connection E117-6 (GCS) - Body ground
Tool Setting 2 V/DIV., 100 ms./DIV.
Condition Theft deterrent system is set (system changes from disarmed state to arming preparation state)

HINT:
·

If the theft warning tilt sensor (yaw rate sensor) is normal, an initial response is output in response to the HI input from the main body ECU (multiplex network body ECU).

·

If the waveform output remains LO, there may be a problem with the main body ECU (multiplex network body ECU), as there is no input from the main body ECU (multiplex network body ECU).



OK:

The waveform displays properly (HI is 6.5 V or higher and LO is below 1 V).




OK

NG

2.CHECK THEFT WARNING TILT SENSOR (YAW RATE SENSOR) (CSIF)
2.CHECK THEFT WARNING TILT SENSOR (YAW RATE SENSOR) (CSIF)
a.
U164269E02
1.219,1.271 0.979,1.875 true 2.104,1.292 1.865,1.896 true 0.083,0.031 0.354,0.229 0.271,0.198 10 false *a 0.667,1.906 1.052,2.104 0.385,0.198 10 false GND 1.573,0.302 1.927,0.521 0.354,0.219 10 false E50 1.656,1.927 2.042,2.125 0.385,0.198 10 false +B

Disconnect the theft warning tilt sensor (yaw rate sensor) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition
E50-5 (CSIF) - E50-1 (GND) Immediately after theft deterrent system set


Result
Result Proceed to
CSIF voltage is below 1 V when theft deterrent system is set A
CSIF voltage is 6.5 V or higher when theft deterrent system is set B

HINT:

With connector E50 of the theft warning tilt sensor (yaw rate sensor) disconnected, measure the voltage at CSIF when the theft deterrent system is set.


Text in Illustration
*a Front view of wire harness connector
(to Theft Warning Tilt Sensor [Yaw Rate Sensor])



A

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEXNETWORK BODY ECU] - THEFT WARNING TILT SENSOR [YAW RATE SENSOR])

B

REPLACE THEFT WARNING TILT SENSOR (YAW RATE SENSOR)

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEXNETWORK BODY ECU] - THEFT WARNING TILT SENSOR [YAW RATE SENSOR])
a.

Disconnect the E117 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the E50 theft warning tilt sensor (yaw rate sensor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E117-6 (GCS) - E50-5 (CSIF) Always Below 1 Ω
E117-6 (GCS) - Body ground Always 10 kΩ or higher


Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE MAIN BODY ECU (MULTIPLEXNETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEXNETWORK BODY ECU)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR