Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM (w/ Entry and Start System) › 2015.08–2017.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255571 THEFT DETERRENT SYSTEM(w/ Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM(w/ Entry and Start System)  B2764  Short to GND in Intrusion Sensor Signal Circuit  


DESCRIPTION

The intrusion sensor (theft warning ultrasonic sensor) conducts self-diagnosis immediately after power is supplied to the sensor (when the theft deterrent system is set).

If a malfunction is detected in the ISIF line, the main body ECU (multiplex network body ECU) stores this DTC.


DTC Code DTC Detection Condition Trouble Area
B2764 After normal/trouble signal is output from intrusion sensor (theft warning ultrasonic sensor) as result of self-diagnosis, following malfunctions are detected:
1.

ISIF line circuit is shorted to ground

2.

Reception of signals other than normal/ trouble signal


·

Map light assembly

·

Intrusion sensor (theft warning ultrasonic sensor)

·

Main body ECU (multiplex network body ECU)

·

Harness or connector



WIRING DIAGRAM

B373997E08
1.615,2.646 2.917,2.875 1.302,0.229 10 false Map Light Assembly 1.115,0.417 1.958,0.677 0.844,0.26 10 false from Battery 4.979,2.604 7.156,3.042 2.177,0.438 10 false Main Body ECU (Multiplex Network Body ECU) 1.479,1.271 3.458,1.75 1.979,0.479 10 false Intrusion Sensor (Theft Warning Ultrasonic Sensor) 1.604,2.479 2.375,2.677 0.771,0.198 10 false R7 0.917,1.552 1.646,1.74 0.729,0.188 10 false GND9 0.667,1.552 1.396,1.74 0.729,0.188 10 false 17 3.74,1.25 4.469,1.438 0.729,0.188 10 false +B2 3.688,1.823 4.417,2.01 0.729,0.188 10 false IOUT 4.083,1.24 4.813,1.427 0.729,0.188 10 false 15 4.115,1.802 4.844,1.99 0.729,0.188 10 false 12 5.396,1.813 6.125,2 0.729,0.188 10 false 12 5.625,1.917 6.354,2.104 0.729,0.188 10 false ISIF 5,2.438 5.771,2.635 0.771,0.198 10 false E117 2.896,0.583 3.938,0.823 1.042,0.24 10 false MPX-B NO.1

CAUTION / NOTICE / HINT

NOTICE:
·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

w/ Door Control Battery:

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>PRECAUTION).



PROCEDURE

1.CHECK INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR) (IOUT)
a.

Using an oscilloscope, check the waveform.

U164405E01
3.453,0.088 3.806,0.252 0.352,0.164 10 R7 1.919,1.299 2.681,1.474 0.762,0.175 10 IOUT 3.965,3.176 4.727,3.351 0.762,0.175 10 *e 3.965,2.588 4.727,2.763 0.762,0.175 10 *d 2.041,3.185 2.803,3.361 0.762,0.175 10 *f 2.517,3.185 3.279,3.361 0.762,0.175 10 *g 2.601,3.54 3.363,3.716 0.762,0.175 10 *d 2.171,2.597 2.933,2.772 0.762,0.175 10 *c 1.648,2.597 2.410,2.772 0.762,0.175 10 *b 1.471,4.073 2.233,4.248 0.762,0.175 10 *i 3.974,4.073 4.736,4.248 0.762,0.175 10 *j 1.069,2.91 1.831,3.085 0.762,0.175 10 LO 1.069,2.449 1.831,2.624 0.762,0.175 10 HI 2.337,2.655 2.443,2.708 false 1.809,2.655 1.915,2.708 false 2.335,1.361 3.159,0.966 false

Text in Illustration
*a Component with harness connected
(Map Light Assembly)
*b IOUT Initial Signal
*c IOUT Initial Response *d Approximately 1.0 seconds
*e Initial Diagnosis *f Approximately 1.0 to 1.6 seconds
*g Approximately 0.05 seconds *h Approximately 5.5 seconds
*i Disarmed State *j Arming Preparation State

Measurement Condition
Tester Connection Content
Tester Connection R7-12 (IOUT) - Body ground
Tool Setting 2 V/DIV., 100 ms./DIV.
Condition Theft deterrent system is set (system changes from disarmed state to arming preparation state)

HINT:
·

If the intrusion sensor (theft warning ultrasonic sensor) is normal, an initial response is output in response to the HI input from the main body ECU (multiplex network body ECU).

·

If the waveform output remains LO, there may be a problem with the main body ECU (multiplex network body ECU), as there is no input from the main body ECU (multiplex network body ECU).



OK:

The waveform displays properly (HI is 6.5 V or higher and LO is below 1 V).




OK

NG

2.CHECK INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR) (IOUT)
2.CHECK INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR) (IOUT)
a.
U166115E01
1.652,0.358 1.864,0.523 0.211,0.165 10 R7 0.098,0.017 0.310,0.182 0.211,0.165 10 *a 0.037,1.886 0.468,2.051 0.430,0.165 10 GND9 3.037,0.493 3.347,0.658 0.310,0.165 10 +B2 0.546,1.969 0.637,1.969 0.637,1.969 0.741,1.355 false 3.023,0.57 2.897,0.57 2.897,0.57 2.675,1.121 false

Disconnect the map light assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition
R7-12 (IOUT) - R7-17(GND9) Immediately after theft deterrent system set


Text in Illustration
*a Front view of wire harness connector
(to Map Light Assembly)


HINT:

With connector R7 of the map light assembly disconnected, measure the voltage at IOUT when the theft deterrent system is set.


Result
Result Proceed to
IOUT voltage is below 1 V when theft deterrent system is set A
IOUT voltage is 6.5 V or higher when theft deterrent system is set B


A

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEXNETWORK BODY ECU] - MAP LIGHT ASSEMBLY)

B

4.INSPECT MAP LAMP ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEXNETWORK BODY ECU] - MAP LIGHT ASSEMBLY)
a.

Disconnect the E117 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the R7 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E117-12 (ISIF) - R7-12(IOUT) Always Below 1 Ω
E117-12 (ISIF) - Body ground Always 10 kΩ or higher
R7-12 (IOUT) - Body ground Always 10 kΩ or higher


Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE MAIN BODY ECU (MULTIPLEXNETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEXNETWORK BODY ECU)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MAP LAMP ASSEMBLY

b.

Remove the intrusion sensor (theft warning ultrasonic sensor) from the map light assembly (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>INTRUSION SENSOR>REMOVAL).


c.
U164384E02
1.177,0.74 1.24,0.74 1.24,0.74 1.542,0.979 true 0.813,1.875 0.885,1.875 0.885,1.875 0.969,2.323 true 1.167,3.135 1.229,3.135 1.229,3.135 1.313,2.385 true 2.865,2.969 2.781,2.969 2.781,2.969 2.563,2.531 true 1.771,1.094 2.208,1.344 2.208,1.344 2.323,1.344 true 2.281,0.51 2.146,0.51 2.146,0.51 1.927,0.958 true 1.667,0.406 1.875,0.573 0.208,0.167 10 false A 1.677,1.729 1.885,1.896 0.208,0.167 10 false B 0.854,0.646 1.198,0.896 0.344,0.25 10 false +B2 0.844,3.063 1.271,3.313 0.427,0.25 10 false IOUT 0.531,1.792 0.875,2.042 0.344,0.25 10 false +B2 2.917,2.875 3.344,3.125 0.427,0.25 10 false GND9 2.365,1.271 2.708,1.521 0.344,0.25 10 false GND 2.333,0.427 2.813,0.729 0.479,0.302 10 false IOUT

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (GND) -B-17 (GND9) Always Below 1 Ω
A-2 (IOUT) -B-12 (IOUT) Always Below 1 Ω
A-4 (+B2) - B-15 (+B2) Always Below 1 Ω


Result
Proceed to
OK
NG



OK

REPLACE INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR)

NG