Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM(w/o Entry and Start System) › from 2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255575 THEFT DETERRENT SYSTEM(w/o Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM(w/o Entry and Start System)  Security Horn Circuit  


DESCRIPTION

When the theft deterrent system is switched from the armed state to the alarm sounding state, the main body ECU (multiplex network body ECU) transmits a signal to cause the security horn to sound at intervals of 0.4 seconds.

WIRING DIAGRAM

B341517E10
0.208,0.958 1.021,1.385 0.813,0.427 10 false from Battery 1.438,1.104 2.042,1.313 0.604,0.208 10 false S-HORN 2.021,0.823 2.156,1.01 0.135,0.188 10 false 1 2.031,1.479 2.167,1.667 0.135,0.188 10 false 5 1.938,1.844 3.448,2.26 1.51,0.417 10 false Horn Relay (S-HORN) 3.021,0.833 3.156,1.021 0.135,0.188 10 false 2 3.021,1.469 3.156,1.656 0.135,0.188 10 false 3 3.875,0.74 4.177,0.948 0.302,0.208 10 false 26 3.875,0.958 4.177,1.167 0.302,0.208 10 false 2H 5.531,0.958 5.708,1.167 0.177,0.208 10 false A 5.5,0.75 5.719,0.969 0.219,0.219 10 false 29 5.844,0.958 6.156,1.156 0.313,0.198 10 false SH 3.938,1.49 5.813,1.698 1.875,0.208 10 false Cowl Side Junction Block LH 5.417,3.125 7.052,3.51 1.635,0.385 10 false Main Body ECU (Multiplex Network Body ECU) 1.49,2.969 1.854,3.177 0.365,0.208 10 false A19 1.479,3.115 3.073,3.333 1.594,0.219 10 false Security Horn Assembly 1.75,2.5 1.896,2.688 0.146,0.188 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

*: w/ Door Control Battery

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>PRECAUTION).



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (SECURITY HORN)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

According to the display on the GTS, perform the Active Test.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Security Horn Security horn OFF/ON -


OK:

The security horn assembly sounds and stops correctly when operated through the GTS.

Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

2.INSPECT SECURITY HORN ASSEMBLY
2.INSPECT SECURITY HORN ASSEMBLY

OK

3.INSPECT HORN RELAY (S-HORN)

NG

3.INSPECT HORN RELAY (S-HORN)
a.
E270109E03
0.451,0.691 0.648,0.849 0.197,0.158 10 5 3.038,0.914 3.235,1.073 0.197,0.158 10 5 1.257,0.685 1.454,0.843 0.197,0.158 10 3 3.038,0.635 3.235,0.793 0.197,0.158 10 3 0.451,1.243 0.648,1.401 0.197,0.158 10 1 3.038,1.198 3.235,1.356 0.197,0.158 10 1 1.263,1.241 1.460,1.399 0.197,0.158 10 2 1.676,1.202 1.873,1.361 0.197,0.158 10 2 2.683,1.292 3.021,1.292 false 1.811,1.292 2.148,1.292 false 2.535,0.995 2.969,0.995 false 2.542,0.729 2.976,0.729 false

Remove the horn relay (S-HORN).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3-5 When battery voltage is applied between terminals 2-1 Below 1 Ω
3-5 When battery voltage is not applied between terminals 2-1 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (HORN RELAY [S-HORN] - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])

NG

REPLACE HORN RELAY [S-HORN]

4.CHECK HARNESS AND CONNECTOR (HORN RELAY [S-HORN] - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])
a.

Remove the main body ECU (multiplex network body ECU) from the cowl side junction block LH.



b.

Connect the cowl side junction block LH connectors.


c.

Remove the horn relay (S-HORN).


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - A-29 (SH) Always Below 1 Ω
2 - Body ground Always 10 kΩ or higher
A-29 (SH) - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (BATTERY - HORN RELAY [S-HORN])

NG

7.CHECK HARNESS AND CONNECTOR (HORN RELAY [S-HORN] - COWL SIDE JUNCTION BLOCK LH)
5.CHECK HARNESS AND CONNECTOR (BATTERY - HORN RELAY [S-HORN])
B341518

a.

Remove the horn relay (S-HORN).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 - Body ground Always 11 to 14 V
5 - Body ground Always 11 to 14 V




OK

6.CHECK HARNESS AND CONNECTOR (HORN RELAY [S-HORN] - SECURITY HORN ASSEMBLY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (HORN RELAY [S-HORN] - SECURITY HORN ASSEMBLY AND BODY GROUND)
a.

Remove the horn relay (S-HORN).


b.

Disconnect the A53 security horn assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - A53-1 Always Below 1 Ω
3 - Body ground Always 10 kΩ or higher
A53-1 - Body ground Always 10 kΩ or higher


Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (HORN RELAY [S-HORN] - COWL SIDE JUNCTION BLOCK LH)
a.

Disconnect the 2H cowl side junction block LH connector.


b.

Remove the horn relay (S-HORN).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 2H-26 Always Below 1 Ω
2 - Body ground Always 10 kΩ or higher
2H-26 - Body ground Always 10 kΩ or higher


Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR