Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM(w/o Entry and Start System) › from 2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255575 THEFT DETERRENT SYSTEM(w/o Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM(w/o Entry and Start System)  Horn Circuit  


DESCRIPTION

When the theft deterrent system is switched from the armed state to the alarm sounding state, the main body ECU (multiplex network body ECU) transmits a signal to cause the horn to sound at intervals of 0.4 seconds.

WIRING DIAGRAM

B432194E05
0.792,0.146 1.854,0.49 1.063,0.344 10 false from Battery 2.594,4.5 3.031,4.698 0.438,0.198 10 false A5 2.25,4.49 2.469,4.688 0.219,0.198 10 false 1 2.031,1.646 2.25,1.844 0.219,0.198 10 false 3 2.052,1.031 2.271,1.229 0.219,0.198 10 false 1 2.917,1.677 3.135,1.875 0.219,0.198 10 false 5 2.938,1.063 3.156,1.26 0.219,0.198 10 false 2 4.823,0.958 5.198,1.198 0.375,0.24 10 false 2H 4.844,0.75 5.219,0.99 0.375,0.24 10 false 27 5.896,0.75 6.271,0.99 0.375,0.24 10 false 28 3.833,4.521 4.271,4.719 0.438,0.198 10 false 1 6.219,0.948 6.969,1.323 0.75,0.375 10 false HORN 2.292,1.875 3.042,2.25 0.75,0.375 10 false HORN 4.219,4.521 4.969,4.896 0.75,0.375 10 false A4 1.063,1.073 1.813,1.448 0.75,0.375 10 false HORN 4.823,3.979 6.542,4.542 1.719,0.563 10 false to Steering Pad Switch Assembly 5.438,3.208 7.156,3.771 1.719,0.563 10 false Main Body ECU (Multiplex Network Body ECU) 2.594,4.667 3.781,5.365 1.188,0.698 10 false Low Pitched Horn Assembly 4.219,4.688 5.417,5.313 1.198,0.625 10 false High Pitched Horn Assembly 4.885,1.938 6.083,2.885 1.198,0.948 10 false Cowl Side Junction Block LH 5.906,0.938 6.281,1.177 0.375,0.24 10 false A 4.833,1.438 5.208,1.677 0.375,0.24 10 false 2J 4.844,1.25 5.219,1.49 0.375,0.24 10 false 22

CAUTION / NOTICE / HINT

NOTICE:
·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

w/ Door Control Battery:

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>PRECAUTION).



PROCEDURE

1.CHECK HORNS OPERATION
a.

Press the horn switch and check if the horns sound.

Result
Result Proceed to
Horns sound A
Horns do not sound B



A

2.INSPECT COWL SIDE JUNCTION BLOCK LH

B

2.INSPECT COWL SIDE JUNCTION BLOCK LH
a.

Remove the main body ECU (multiplex network body ECU) from the cowl side junction block LH (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL).

U164271E03
6.292,1.26 6.292,1.5 6.292,1.5 6.115,1.5 true 1.292,0.427 1.729,0.604 0.438,0.177 10 false 2H 4.875,0.542 5.104,0.677 0.229,0.135 10 false A 5.688,1.438 6.156,1.594 0.469,0.156 10 false HORN


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2H-27 - A-28 (HORN) Always Below 1 Ω


Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG (for LHD) C
NG (for RHD) D



A

REPLACE MAIN BODY ECU [MULTIPLEX NETWORKBODY ECU] (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU [MULTIPLEX NETWORKBODY ECU]

C

D