The combination meter receives engine speed signals from the ECM via the CAN line. The combination meter displays engine speed data that is calculated based on the data received from the ECM.
Check for DTCs (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| CAN communication system DTC is not output | A |
| CAN communication system (for LHD) DTC is output | B |
| CAN communication system (for RHD) DTC is output | C |
A
B
C
Operate the intelligent tester according to the display and select Active Test (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| TachoMeter Operation | Tachometer | 0, 1000, 2000, 3000, 4000, 5000, 6000, 7000 | Perform the test with the vehicle stopped and engine idling. |
Make sure that the vehicle is stopped and the engine is idling.
Needle indication is normal.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/ Multi-information Display) | B |
| NG (w/o Multi-information Display) | C |
A
B
(See pageVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER(w/ Multi-information Display)>REMOVAL)
C
(See pageVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER(w/o Multi-information Display)>REMOVAL)
Operate the intelligent tester according to the display and select Data List (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Engine Rpm | Engine speed/Min.: 0, Max.: 12750 | Idling: 700 to 800 | Unit: rpm |
Engine speed displayed on the intelligent tester is almost the same as actual engine speed.
| Result | Proceed to |
|---|---|
| NG | A |
| OK (w/ Multi-information Display) | B |
| OK (w/o Multi-information Display) | C |
A
B
(See pageVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER(w/ Multi-information Display)>REMOVAL)
C
(See pageVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER(w/o Multi-information Display)>REMOVAL)
Operate the intelligent tester according to the display and select Data List (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).
| Result | Proceed to |
|---|---|
| Engine speed displayed on the intelligent tester is almost same as actual engine speed | A |
| Engine speed displayed on the intelligent tester is not same as actual engine speed (for 1GR-FE) | B |
| Engine speed displayed on the intelligent tester is not same as actual engine speed (for 1UR-FE) | C |
| Engine speed displayed on the intelligent tester is not same as actual engine speed (for 3UR-FE) | D |
| Engine speed displayed on the intelligent tester is not same as actual engine speed (for 1VD-FTV) | E |
Engine speed displayed on the intelligent tester is almost the same as actual engine speed.
A
B
C
D
E
Check the combination meter type.
| Result | Proceed to |
|---|---|
| w/ Multi-information Display | A |
| w/o Multi-information Display | B |
A
(See pageVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER(w/ Multi-information Display)>REMOVAL)
B
(See pageVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER(w/o Multi-information Display)>REMOVAL)