Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052841 METER / GAUGE / DISPLAY _0255598 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Engine Coolant Temperature Gauge Malfunction  


DESCRIPTION

In this circuit, the combination meter assembly receives engine coolant temperature signals from the ECM using CAN communication lines. The combination meter assembly displays an engine coolant temperature that is calculated based on the data received from the ECM.

WIRING DIAGRAM

E349719E04
1.635,3.083 2.094,3.281 0.458,0.198 10 false ECM 3.281,2.073 4.094,2.302 0.813,0.229 10 false CAN Line 4.438,3.094 6.531,3.344 2.094,0.25 10 false Combination Meter Assembly

CAUTION / NOTICE / HINT

HINT:

If there is an open or short in the engine coolant temperature sensor circuit, an SFI system DTC is output. If output, perform troubleshooting on the SFI system first.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check for DTCs (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
CAN communication system DTC is not output A
CAN communication system (for LHD) DTC is output B
CAN communication system (for RHD) DTC is output C



A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (COOLANT TEMP)

B

C

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (COOLANT TEMP)
a.

Operate the intelligent tester according to the display and select Active Test.

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Water Temperature Meter Operation Engine coolant temperature receiver gauge LOW, NORMAL or HIGH Perform the test with the vehicle stopped and engine idling.

HINT:

Confirm that the vehicle is stopped and the engine is idling.


OK:

Needle indication is normal.


Result
Result Proceed to
OK A
NG (w/ Multi-information Display) B
NG (w/o Multi-information Display) C



A

3.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMPERATURE)

B

C

3.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMPERATURE)
a.

Operate the intelligent tester according to the display and select Data List.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Coolant Temperature Engine coolant temperature/Min.: -40 (-40), Max.: 140 (284) After warming up: 80 to 105 (176 to 221)
·

Unit: °C (°F)

·

If the value is -40 (-40): The sensor circuit is open

·

If the value is 140 (284): The sensor circuit is shorted.



OK:

Coolant temperature displayed on the intelligent tester is between 80°C (176°F) and 95°C (203°F) after warming up.


Result
Result Proceed to
OK A
NG (w/ Multi-information Display) B
NG (w/o Multi-information Display) C



A

4.READ VALUE USING INTELLIGENT TESTER (ENGINE COOLANT)

B

C

4.READ VALUE USING INTELLIGENT TESTER (ENGINE COOLANT)
a.

Operate the intelligent tester according to the display and select Data List.

Engine*1, *2, *3
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Coolant Temp Engine coolant temperature:
Min.: -40°C, Max.:140°C
80 to 100°C (176 to 212°F):
After warming up
·

If the value is -40°C (-40°F), the sensor circuit is open.

·

If the value is 140°C (284°F), the sensor circuit is shorted.



Engine*4
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Coolant Temp Engine coolant temperature/
Min.: -40°C, Max.:140°C
After warming up engine: 75 to 90°C (167 to 194°F)
·

If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted.

·

After a long soak, the coolant temperature, intake air temperature, and ambient air temperature are approximately equal.



*1: for 1GR-FE

*2: for 1UR-FE

*3: for 3UR-FE

*4: for 1VD-FTV


OK:

Engine coolant temperature value displayed on the intelligent tester is almost the same as actual engine coolant temperature.


Result
Result Proceed to
OK A
NG (for 1GR-FE) B
NG (for 1UR-FE) C
NG (for 3UR-FE) D
NG (for 1VD-FTV) E



A

5.REPLACE COMBINATION METER ASSEMBLY

B

C

D

E

5.REPLACE COMBINATION METER ASSEMBLY
a.

w/ Multi-information Display:

i.

Temporarily replace the combination meter with a new one (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER(w/ Multi-information Display)>REMOVAL).



b.

w/o Multi-information Display:

i.

Temporarily replace the combination meter with a new one (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER(w/o Multi-information Display)>REMOVAL).




NEXT

6.CHECK COMBINATION METER ASSEMBLY
6.CHECK COMBINATION METER ASSEMBLY
a.

w/ Multi-information Display:

i.

Check that the operation of the combination meter returns to normal (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER(w/ Multi-information Display)>REMOVAL).



b.

w/o Multi-information Display:

i.

Check that the operation of the combination meter returns to normal (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER(w/o Multi-information Display)>REMOVAL).



OK:

Operation of combination meter returns to normal.


Result
Result Proceed to
OK A
NG (for 1GR-FE) B
NG (for 1UR-FE) C
NG (for 3UR-FE) D
NG (for 1VD-FTV) E


A

END (COMBINATION METER IS DEFECTIVE)

B

C

D

E