This DTC is output when the combination meter detects a fuel sender gauge malfunction via the CAN.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1500 | When the combination meter detects a fuel sender gauge malfunction. | ·
Harness or connector ·
Combination meter assembly ·
Fuel suction with pump and gauge tube assembly ·
Fuel sender gauge assembly |
Operate the GTS according to the display and select the Data List (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Fuel Input | Fuel sender gauge (main) input signal/Min.: 0, Max.: 127.5 | Fuel receiver gauge indicates F: 83.7 L
Fuel receiver gauge indicates 3/4: 66.5 L Fuel receiver gauge indicates 1/2: 49.5 L Fuel receiver gauge indicates 1/4: 31.2 L Fuel receiver gauge indicates E: 12.5 L |
Unit: L |
Fuel value displayed on the GTS is almost the same as needle indication.
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Disconnect the E119 combination meter assembly connectors.
Disconnect the N1 fuel suction with pump and gauge tube assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E119-33 (FR) - N1-3 (FR) | Always | Below 1 Ω |
| E119-35 (FV) - N1-1 (FV) | Always | Below 1 Ω |
| E119-17 (FE&B) - N1-2 (FE) | Always | Below 1 Ω |
| E119-33 (FR) or N1-3 (FR) - Body ground | Always | Below 1 Ω |
| E119-35 (FV) or N1-1 (FV) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the fuel sender gauge assembly.
for 1GR-FE (See page Engine / Hybrid System>1GR-FE (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL)
for 1UR-FE (See page Engine / Hybrid System>1UR-FE (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL)
for 1VD-FTV (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL)
for 3UR-FE (See page Engine / Hybrid System>3UR-FE (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL)
Inspect the fuel sender gauge assembly.
for 1GR-FE (See page Engine / Hybrid System>1GR-FE (FUEL)>FUEL SENDER GAUGE ASSEMBLY>INSPECTION)
for 1UR-FE (See page Engine / Hybrid System>1UR-FE (FUEL)>FUEL SENDER GAUGE ASSEMBLY>INSPECTION)
for 1VD-FTV (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL SENDER GAUGE ASSEMBLY>INSPECTION)
for 3UR-FE (See page Engine / Hybrid System>3UR-FE (FUEL)>FUEL SENDER GAUGE ASSEMBLY>INSPECTION)
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 1GR-FE) | B |
| NG (for 1UR-FE) | C |
| NG (for 3UR-FE) | D |
| NG (for 1VD-FTV) | E |
A
B
C
D
E
Remove the fuel sender gauge assembly.
for 1GR-FE (See page Engine / Hybrid System>1GR-FE (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL)
for 1UR-FE (See page Engine / Hybrid System>1UR-FE (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL)
for 1VD-FTV (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL)
for 3UR-FE (See page Engine / Hybrid System>3UR-FE (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-2 (FS) - B-2 (FS) | Always | Below 1 Ω |
| A-3 (FE) - B-1 (FE) | Always | Below 1 Ω |
| *a | Upper Side |
| *b | Lower Side
(to Fuel Sender Gauge Assembly) |
| *c | Connector A |
| *d | Connector B |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 1GR-FE) | B |
| NG (for 1UR-FE) | C |
| NG (for 3UR-FE) | D |
| NG (for 1VD-FTV) | E |
A
B
C
D
E