Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2015.08
RM2660E _58 Vehicle Interior _052841 METER / GAUGE / DISPLAY _0255598 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B150A  Lost Communication with HMI-LAN  


DESCRIPTION

*1: w/ Navigation System

*2: w/ Audio and Display System


The combination meter assembly receives a text data signal from the multi-media module receiver assembly*1 or radio and display receiver assembly*2 via local bus communication.

Based on this signal, audio and visual system or navigation system information is displayed on the multi-information display.

This DTC is stored when the combination meter assembly cannot receive the signal.

DTC No. DTC Detection Condition Trouble Area
B150A After the combination meter assembly receives a registration information signal, which is sent by the multi-media module receiver assembly when the ignition switch is turned ACC, 1 or more times, the combination meter assembly does not receive the signal for 30 seconds or more.
·

Harness or connector

·

Multi-media module receiver assembly*1

·

Radio and display receiver assembly*2

·

Combination meter assembly



WIRING DIAGRAM

for LHD with Navigation System:


E274272E93
0.813,1.906 3.323,2.229 2.51,0.323 10 false Multi-media Module Receiver Assembly 2.26,0.594 2.448,0.76 0.188,0.167 10 false 1 4.885,0.573 5.094,0.74 0.208,0.167 10 false 37 4.833,1.74 5.167,1.906 0.333,0.167 10 false E119 4.833,1.906 6.781,2.177 1.948,0.271 10 false Combination Meter Assembly 0.813,1.75 1.271,1.917 0.458,0.167 10 false F77 1.75,0.74 2.167,0.906 0.417,0.167 10 false CANH 5.146,0.74 5.563,0.906 0.417,0.167 10 false MSCH 5.156,1.302 5.573,1.469 0.417,0.167 10 false MSCL 2.26,1.156 2.448,1.333 0.188,0.177 10 false 2 4.885,1.146 5.094,1.333 0.208,0.188 10 false 38 0.979,2.375 3.125,2.646 2.146,0.271 10 false : Local Bus Communication Line 1.76,1.302 2.177,1.469 0.417,0.167 10 false CANL


for RHD with Navigation System:


E274272E94
0.896,1.865 3.51,2.094 2.615,0.229 10 false Multi-media Module Receiver Assembly 2.26,0.594 2.448,0.76 0.188,0.167 10 false 20 4.885,0.573 5.094,0.74 0.208,0.167 10 false 37 4.833,1.74 5.198,1.958 0.365,0.219 10 false E119 4.833,1.906 6.781,2.177 1.948,0.271 10 false Combination Meter Assembly 0.906,1.708 1.219,1.885 0.313,0.177 10 false F77 1.792,0.74 2.208,0.906 0.417,0.167 10 false CAH2 5.146,0.74 5.563,0.906 0.417,0.167 10 false MSCH 5.156,1.302 5.573,1.469 0.417,0.167 10 false MSCL 2.26,1.156 2.448,1.333 0.188,0.177 10 false 21 4.885,1.146 5.094,1.333 0.208,0.188 10 false 38 0.979,2.375 3.125,2.646 2.146,0.271 10 false : Local Bus Communication Line 1.771,1.302 2.188,1.469 0.417,0.167 10 false CAL2


w/ Audio and Display System:


E274272E95
0.854,1.885 3.25,2.156 2.396,0.271 10 false Radio and Display Receiver Assembly 2.26,0.594 2.448,0.76 0.188,0.167 10 false 9 4.885,0.573 5.094,0.74 0.208,0.167 10 false 37 4.833,1.74 5.167,1.906 0.333,0.167 10 false E119 4.833,1.906 6.781,2.177 1.948,0.271 10 false Combination Meter Assembly 0.844,1.708 1.188,1.885 0.344,0.177 10 false F124 1.76,0.74 2.177,0.906 0.417,0.167 10 false CANH 5.146,0.74 5.563,0.906 0.417,0.167 10 false MSCH 5.156,1.302 5.573,1.469 0.417,0.167 10 false MSCL 2.26,1.156 2.448,1.333 0.188,0.177 10 false 10 4.885,1.146 5.094,1.333 0.208,0.188 10 false 38 0.979,2.375 3.125,2.646 2.146,0.271 10 false : Local Bus Communication Line 1.771,1.302 2.188,1.469 0.417,0.167 10 false CANH


PROCEDURE

1.CHECK FOR DTC (NAVIGATION SYSTEM*1 or AUDIO AND VISUAL SYSTEM*2)

*1: w/ Navigation System

*2: w/ Audio and Display System




Result:
Result Proceed to
Navigation system DTCs are not output. (w/ Navigation System) A
Audio and visual system DTCs are not output. (w/ Audio and Display System) B
Navigation system DTCs are output. (w/ Navigation System) C
Audio and visual system DTCs are output. (w/ Audio and Display System) D



A

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY)

B

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)

C

D

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY)
a.

Disconnect the E119 combination meter assembly connector.


b.

Disconnect the F77 multi-media module receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for LHD):
Tester Connection Condition Specified Condition
E119-37 (MSCH) - F77-1 (CANH) Always Below 1 Ω
E119-38 (MSCL) - F77-2 (CANL) Always Below 1 Ω
E119-37 (MSCH) or F77-1 (CANH) - Body ground Always 10 kΩ or higher
E119-38 (MSCL) or F77-2 (CANL) - Body ground Always 10 kΩ or higher


Standard Resistance (for RHD):
Tester Connection Condition Specified Condition
E119-37 (MSCH) - F77-20 (CAH2) Always Below 1 Ω
E119-38 (MSCL) - F77-21 (CAL2) Always Below 1 Ω
E119-37 (MSCH) or F77-20 (CAH2) - Body ground Always 10 kΩ or higher
E119-38 (MSCL) or F77-21 (CAL2) - Body ground Always 10 kΩ or higher




OK

3.CHECK COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly with a new or known good one (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).


b.

Turn the ignition switch to ON and wait 30 seconds.

NOTICE:

A maximum of 30 seconds is required to send/receive the registration information between the combination meter assembly and navigation receiver assembly.



c.

Operate the steering pad switch assembly and check that the audio tab illuminates.


d.

Check for DTCs (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
The audio tab illuminates and DTC B150A is not output. A
The audio tab does not illuminate and DTC B150A is output. B




OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the E119 combination meter assembly connector.


b.

Disconnect the F124 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E119-37 (MSCH) - F124-9 (CANH) Always Below 1 Ω
E119-38 (MSCL) - F124-10 (CANL) Always Below 1 Ω
E119-37 (MSCH) or F124-9 (CANH) - Body ground Always 10 kΩ or higher
E119-38 (MSCL) or F124-10 (CANL) - Body ground Always 10 kΩ or higher




OK

5.CHECK COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly with a new or known good one (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).


b.

Turn the ignition switch to ON and wait 30 seconds.

NOTICE:

A maximum of 30 seconds is required to send/receive the registration information between the combination meter assembly and the radio and display receiver assembly.



c.

Operate the steering pad switch assembly and check that the audio tab illuminates.


d.

Check for DTCs (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).

Result:
Result Proceed to
The audio tab illuminates and DTC B150A is not output. A
The audio tab does not illuminate and DTC B150A is output. B




OK

END (COMBINATION METER ASSEMBLY IS DEFECTIVE)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY