Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052843 SUPPLEMENTAL RESTRAINT SYSTEMS _0255601 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1800/51  Short in Driver Side Squib Circuit  B1801/51  Open in Driver Side Squib Circuit  B1802/51  Short to GND in Driver Side Squib Circuit  B1803/51  Short to B+ in Driver Side Squib Circuit  


DESCRIPTION

The driver side squib circuit consists of the center airbag sensor, the spiral cable, and the steering pad.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the driver side squib circuit.


DTC Code DTC Detection Condition Trouble Area
B1800/51 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal 5 times in the driver side squib circuit during the primary check.

·

A driver side squib malfunction.

·

A spiral cable malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Spiral cable

·

Steering pad (Driver side squib)

·

Center airbag sensor assembly


B1801/51 When one of the following conditions is met:
·

The A center airbag sensor receives an open circuit signal in the driver side squib circuit for 2 seconds.

·

A driver side squib malfunction.

·

A spiral cable malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Spiral cable

·

Steering pad (Driver side squib)

·

Center airbag sensor assembly


B1802/51 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to ground signal in the driver side squib circuit for 0.5 seconds.

·

A driver side squib malfunction.

·

A spiral cable malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Spiral cable

·

Steering pad (Driver side squib)

·

Center airbag sensor assembly


B1803/51 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to B+ signal in the driver side squib circuit for 0.5 seconds.

·

A driver side squib malfunction.

·

A spiral cable malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Spiral cable

·

Steering pad (Driver side squib)

·

Center airbag sensor assembly



WIRING DIAGRAM

U164910E01
2.921,1.556 3.147,1.712 0.225,0.156 10 D+ 2.921,2.397 3.098,2.552 0.177,0.156 10 D- 4.913,1.655 5.138,1.811 0.225,0.156 10 D+ 4.913,2.496 5.089,2.652 0.177,0.156 10 D- 3.253,1.562 3.478,1.752 0.225,0.191 10 1 3.253,2.409 3.430,2.600 0.177,0.191 10 2 2.496,2.985 2.770,3.148 0.274,0.163 10 E13 2.496,3.14 3.305,3.310 0.809,0.170 10 Spiral Cable 0.801,2.985 1.971,3.356 1.170,0.371 10 z39 Driver Side Squib 4.611,1.543 4.774,1.782 0.163,0.239 10 5 4.611,2.377 4.851,2.602 0.239,0.225 10 6 4.829,4.155 5.131,4.297 0.302,0.142 10 E47 4.829,4.317 6.207,4.487 1.378,0.170 10 Center Airbag Sensor 2.496,2.419 2.722,2.609 0.225,0.191 10 1 2.496,1.571 2.673,1.762 0.177,0.191 10 2

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:

To perform the simulation method, enter the check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various type of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK STEERING PAD (DRIVER SIDE SQUIB)
a.

Turn the ignition switch off.

U164739E01
2.181,2.594 2.309,2.748 0.127,0.154 10 C 2.074,2.594 2.202,2.748 0.127,0.154 10 D 1.149,2.594 1.276,2.748 0.127,0.154 10 E 0.97,2.594 1.097,2.748 0.127,0.154 10 F 1.283,2.828 2.083,2.989 0.800,0.161 10 Spiral Cable 2.288,3.11 3.703,3.295 1.415,0.185 10 Center Airbag Sensor 0.305,3.234 1.457,3.387 1.151,0.154 10 Driver Side Squib 0.857,2.529 0.857,3.204 false 2.181,1.152 2.309,1.306 0.127,0.154 10 C 2.074,1.152 2.202,1.306 0.127,0.154 10 D 1.149,1.152 1.276,1.306 0.127,0.154 10 E 0.97,1.152 1.097,1.306 0.127,0.154 10 F 1.283,1.386 2.083,1.547 0.800,0.161 10 Spiral Cable 2.327,1.45 3.743,1.635 1.415,0.185 10 Center Airbag Sensor 1.001,0.427 2.152,0.581 1.151,0.154 10 Driver Side Squib 0.088,0.043 1.419,0.314 1.332,0.272 12 w/ Side Airbag: 0.088,1.722 1.419,1.993 1.332,0.272 12 w/o Side Airbag: 0.883,0.976 0.883,0.482 0.883,0.482 0.983,0.482 false 4.188,0.751 6.543,1.221 2.354,0.471 10 Front view of wire harness connector: (to Driver Side Squib) 4.581,1.838 4.875,2.021 0.294,0.183 10 z39 5.909,1.691 6.716,1.861 0.807,0.169 10 Connector E 6.201,2.124 6.510,2.279 0.308,0.156 10 SST 5.86,2.446 6.778,2.616 0.918,0.169 10 Color: Orange 5.764,1.985 6.182,2.181 false 5.556,2.39 5.826,2.515 false


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the steering pad.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (orange connector).

CAUTION:

Never connect the tester to the steering pad (driver side squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1800, B1801, B1802 or B1803 is not output.


HINT:

Codes other than DTC B1800, B1801, B1802 and B1803 may be output at this time, but they are not related to this check.




OK

NG

2.CHECK CONNECTOR
2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector E.


d.

Check that the spiral cable connectors (on the steering pad side) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.




OK

3.CHECK DRIVER SIDE SQUIB CIRCUIT

NG

3.CHECK DRIVER SIDE SQUIB CIRCUIT
a.

Disconnect the connectors from the center airbag sensor.

U164743E01
2.524,2.407 2.563,2.368 false 2.524,2.46 2.61,2.373 false 2.524,2.513 2.61,2.426 false 2.524,2.566 2.61,2.479 false 2.57,2.573 2.61,2.532 false 2.517,0.965 2.556,0.926 false 2.517,1.018 2.604,0.932 false 2.517,1.071 2.604,0.985 false 2.517,1.124 2.604,1.037 false 2.563,1.131 2.604,1.09 false 2.889,0.941 3.034,1.086 0.145,0.145 10 A 2.51,1.156 2.655,1.300 0.145,0.145 10 B 2.889,2.385 3.034,2.529 0.145,0.145 10 A 2.51,2.599 2.655,2.744 0.145,0.145 10 B 2.183,2.599 2.328,2.744 0.145,0.145 10 C 2.083,2.599 2.228,2.744 0.145,0.145 10 D 1.15,2.599 1.295,2.744 0.145,0.145 10 E 0.971,2.599 1.116,2.744 0.145,0.145 10 F 1.272,2.831 2.078,2.999 0.805,0.168 10 Spiral Cable 2.511,3.107 3.907,3.308 1.396,0.201 10 Center Airbag Sensor 1.028,3.153 2.175,3.296 1.147,0.143 10 Driver Side Squib 0.884,2.527 0.884,3.216 0.884,3.216 1.004,3.216 false 2.183,1.152 2.328,1.296 0.145,0.145 10 C 2.083,1.152 2.228,1.296 0.145,0.145 10 D 1.15,1.152 1.295,1.296 0.145,0.145 10 E 0.971,1.152 1.116,1.296 0.145,0.145 10 F 1.272,1.383 2.078,1.552 0.805,0.168 10 Spiral Cable 2.511,1.445 3.907,1.646 1.396,0.201 10 Center Airbag Sensor 1.028,0.454 2.175,0.597 1.147,0.143 10 Driver Side Squib 0.884,0.974 0.884,0.523 0.884,0.523 1.004,0.523 false 0.211,1.791 1.523,2.048 1.312,0.257 12 w/o Side Airbag: 0.211,0.035 1.523,0.292 1.312,0.257 12 w/ Side Airbag: 4.299,0.885 6.735,1.246 2.436,0.362 10 Front view of wire harness connector: (to Driver Side Squib) 4.719,1.581 4.988,1.739 0.269,0.159 10 z39 4.878,1.99 5.038,2.127 0.160,0.137 10 1 5.858,1.99 6.112,2.127 0.254,0.137 10 2 5.439,1.752 5.835,2.066 false 5.359,1.752 4.962,2.066 false 5.694,1.62 6.507,1.766 0.813,0.147 10 Connector E 5.849,2.481 6.831,2.646 0.982,0.164 10 Color: Orange 5.557,2.34 5.825,2.533 false


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
z39-1 - Body ground Ignition switch ON Below 1 V
z39-2 - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z39-1 - z39-2 Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z39-1 - z39-2 Always 1 MΩ or higher
z39-1 - Body ground Always 1 MΩ or higher
z39-2 - Body ground Always 1 MΩ or higher




OK

4.CHECK CENTER AIRBAG SENSOR

NG

5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - SPIRAL CABLE)
4.CHECK CENTER AIRBAG SENSOR
a.
C173643E01
1.712,3.334 1.864,3.485 0.151,0.151 10 D 1.83,3.334 1.981,3.485 0.151,0.151 10 C 0.453,3.334 0.604,3.485 0.151,0.151 10 F 0.571,3.334 0.722,3.485 0.151,0.151 10 E 0.719,3.613 1.517,3.773 0.798,0.159 10 Spiral Cable 2.203,3.984 3.151,4.311 0.948,0.328 10 Center Airbag Sensor 0.487,4.026 1.657,4.195 1.170,0.170 10 Driver Side Squib 0.357,3.262 0.357,4.113 0.357,4.113 0.463,4.113 false 1.712,1.575 1.864,1.726 0.151,0.151 10 D 1.83,1.575 1.981,1.726 0.151,0.151 10 C 0.453,1.575 0.604,1.726 0.151,0.151 10 F 0.571,1.575 0.722,1.726 0.151,0.151 10 E 0.719,1.854 1.517,2.014 0.798,0.159 10 Spiral Cable 2.203,1.932 3.151,2.260 0.948,0.328 10 Center Airbag Sensor 0.487,0.581 1.657,0.750 1.170,0.170 10 Driver Side Squib 0.357,1.353 0.357,0.66 0.357,0.66 0.463,0.66 false 0.045,2.34 1.340,2.566 1.295,0.225 12 w/o Side Airbag: 0.045,0.002 1.340,0.227 1.295,0.225 12 w/ Side Airbag:

Connect the connectors to the steering pad and the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1800, B1801, B1802 or B1803 is not output.


HINT:

Codes other than DTC B1800, B1801, B1802 and B1803 may be output at this time, but they are not related to this check.




OK

NG

5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - SPIRAL CABLE)
a.

Restore the released activation prevention mechanism of connector B to its original condition.

U164747E02
2.406,2.552 2.25,3.26 2.25,3.26 2.156,3.26 false 2.396,0.979 2.396,0.479 2.396,0.479 2.302,0.479 false 5.615,1.938 6.031,2.417 false 5.49,1.948 5.083,2.427 false 2.521,2.375 2.552,2.344 false 2.521,2.427 2.604,2.344 false 2.521,2.479 2.604,2.396 false 2.521,2.531 2.604,2.448 false 2.563,2.542 2.604,2.5 false 2.521,0.927 2.552,0.885 false 2.521,0.979 2.604,0.896 false 2.521,1.031 2.604,0.948 false 2.521,1.083 2.604,1 false 2.563,1.094 2.604,1.052 false 2.521,2.615 2.667,2.76 0.146,0.146 10 false B 2.167,2.615 2.313,2.76 0.146,0.146 10 false C 1.979,2.615 2.125,2.76 0.146,0.146 10 false D 1.031,2.615 1.177,2.76 0.146,0.146 10 false E 0.844,2.615 0.99,2.76 0.146,0.146 10 false F 2.875,2.385 3.042,2.552 0.167,0.167 10 false A 2.521,3.125 3.917,3.302 1.396,0.177 10 false Center Airbag Sensor 1.156,2.823 2.01,2.979 0.854,0.156 10 false Spiral Cable 0.76,3.177 2.219,3.365 1.458,0.188 10 false Instrument Panel Wire 2.521,1.177 2.667,1.323 0.146,0.146 10 false B 2.167,1.177 2.313,1.323 0.146,0.146 10 false C 1.979,1.177 2.125,1.323 0.146,0.146 10 false D 1.031,1.177 1.177,1.323 0.146,0.146 10 false E 0.844,1.177 0.99,1.323 0.146,0.146 10 false F 2.875,0.958 3.042,1.125 0.167,0.167 10 false A 2.51,1.448 3.906,1.625 1.396,0.177 10 false Center Airbag Sensor 1.156,1.375 1.99,1.563 0.833,0.188 10 false Spiral Cable 0.906,0.385 2.365,0.573 1.458,0.188 10 false Instrument Panel Wire 0.031,1.74 1.375,1.99 1.344,0.25 12 false w/o Side Airbag: 0.031,0.052 1.375,0.302 1.344,0.25 12 false w/ Side Airbag: 4.26,0.75 6.583,1.104 2.323,0.354 10 false Rear view of wire harness connector: (to Spiral Cable) 4.448,1.677 4.771,1.885 0.323,0.208 10 false E13 5.958,1.75 6.792,1.969 0.833,0.219 10 false Connector C 6.031,2.448 6.313,2.635 0.281,0.188 10 false D+ 4.99,2.469 5.208,2.688 0.219,0.219 10 false D-


b.

Disconnect the instrument panel wire connector from the spiral cable.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E13-1 (D+) - Body ground Ignition switch ON Below 1 V
E13-2 (D-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E13-1 (D+) - E13-2 (D-) Always Below 1 Ω



h.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E13-1 (D+) - E13-2 (D-) Always 1 MΩ or higher
E13-1 (D+) - Body ground Always 1 MΩ or higher
E13-2 (D-) - Body ground Always 1 MΩ or higher




OK

NG

REPLACE INSTRUMENT PANEL WIRE