Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2015.08
RM2660E _58 Vehicle Interior _052843 SUPPLEMENTAL RESTRAINT SYSTEMS _0255601 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1810/53  Short in Driver Side Squib 2nd Step Circuit  B1811/53  Open in Driver Side Squib 2nd Step Circuit  B1812/53  Short to GND in Driver Side Squib 2nd Step Circuit  B1813/53  Short to B+ in Driver Side Squib 2nd Step Circuit  


DESCRIPTION

The driver side squib 2nd step circuit consists of the center airbag sensor, the spiral cable, and the steering pad.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the driver side squib 2nd step circuit.

DTC Code DTC Detection Condition Trouble Area
B1810/53 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal 5 times in the driver side squib 2nd step circuit during the primary check.

·

A driver side squib 2nd step malfunction.

·

A spiral cable malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Spiral cable

·

Steering pad (Driver side squib 2nd step)

·

Center airbag sensor assembly


B1811/53 When one of the following conditions is met:
·

The center airbag sensor receives an open circuit signal in the driver side squib 2nd step circuit for 2 seconds.

·

A driver side squib 2nd step malfunction.

·

A spiral cable malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Spiral cable

·

Steering pad (Driver side squib 2nd step)

·

Center airbag sensor assembly


B1812/53 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to ground signal in the driver side 2nd step circuit for 0.5 seconds.

·

A driver side squib 2nd step malfunction.

·

A spiral cable malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Spiral cable

·

Steering pad (Driver side squib 2nd step)

·

Center airbag sensor assembly


B1813/53 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to B+ signal in the driver side squib 2nd step circuit for 0.5 seconds.

·

A driver side squib 2nd step malfunction.

·

A spiral cable malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Spiral cable

·

Steering pad (Driver side squib 2nd step)

·

Center airbag sensor assembly



WIRING DIAGRAM

C342732E02
0.677,3.198 2.573,3.438 1.896,0.24 10 false Driver Side Squib 2nd Step 0.677,3.021 1.208,3.25 0.531,0.229 10 false z38 2.552,3.188 3.427,3.438 0.875,0.25 10 false Spiral Cable 2.552,3.021 2.979,3.25 0.427,0.229 10 false E13 4.854,4.323 6.417,4.552 1.563,0.229 10 false Center Airbag Sensor 4.854,4.146 5.281,4.375 0.427,0.229 10 false E47 4.813,1.677 5.24,1.906 0.427,0.229 10 false D2+ 4.813,2.479 5.24,2.708 0.427,0.229 10 false D2- 2.885,1.552 3.219,1.781 0.333,0.229 10 false D2+ 2.885,2.406 3.188,2.646 0.302,0.24 10 false D2- 4.552,1.563 4.771,1.792 0.219,0.229 10 false 8 4.563,2.396 4.781,2.625 0.219,0.229 10 false 7 3.25,1.573 3.469,1.802 0.219,0.229 10 false 4 3.26,2.385 3.479,2.615 0.219,0.229 10 false 3 2.458,1.583 2.677,1.813 0.219,0.229 10 false 2 2.469,2.406 2.688,2.635 0.219,0.229 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

After replacing the center airbag sensor assembly, refer to initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:

To perform the simulation method, enter the check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various type of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK STEERING PAD (DRIVER SIDE SQUIB 2ND STEP)
a.

Turn the ignition switch off.

U164742E01
2.181,2.594 2.309,2.748 0.127,0.154 10 C 2.074,2.594 2.202,2.748 0.127,0.154 10 D 1.149,2.594 1.276,2.748 0.127,0.154 10 E 0.97,2.594 1.097,2.748 0.127,0.154 10 F 1.283,2.828 2.083,2.989 0.800,0.161 10 Spiral Cable 2.288,3.11 3.703,3.295 1.415,0.185 10 Center Airbag Sensor 0.305,3.234 1.457,3.387 1.151,0.154 10 Driver Side Squib 0.857,2.529 0.857,3.204 false 2.181,1.152 2.309,1.306 0.127,0.154 10 C 2.074,1.152 2.202,1.306 0.127,0.154 10 D 1.149,1.152 1.276,1.306 0.127,0.154 10 E 0.97,1.152 1.097,1.306 0.127,0.154 10 F 1.283,1.386 2.083,1.547 0.800,0.161 10 Spiral Cable 2.327,1.45 3.743,1.635 1.415,0.185 10 Center Airbag Sensor 1.001,0.427 2.152,0.581 1.151,0.154 10 Driver Side Squib 0.088,0.043 1.419,0.314 1.332,0.272 12 w/ Side Airbag: 0.088,1.722 1.419,1.993 1.332,0.272 12 w/o Side Airbag: 0.883,0.976 0.883,0.482 0.883,0.482 0.983,0.482 false 4.188,0.751 6.543,1.221 2.354,0.471 10 Front view of wire harness connector: (to Driver Side Squib) 4.581,1.838 4.875,2.021 0.294,0.183 10 z38 5.909,1.691 6.716,1.861 0.807,0.169 10 Connector E 6.201,2.124 6.510,2.279 0.308,0.156 10 SST 5.86,2.446 6.778,2.616 0.918,0.169 10 Color: Black 5.764,1.985 6.182,2.181 false 5.556,2.39 5.826,2.515 false


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the steering pad.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (black connector).

CAUTION:

Never connect the tester to the steering pad (driver side squib 2nd step) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1810, B1811, B1812 or B1813 is not output.


HINT:

Codes other than DTC B1810, B1811, B1812 and B1813 may be output at this time, but they are not related to this check.




OK

NG

2.CHECK CONNECTOR
2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector E.


d.

Check that the spiral cable connectors (on the steering pad side) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.




OK

3.CHECK DRIVER SIDE SQUIB 2ND STEP CIRCUIT

NG

3.CHECK DRIVER SIDE SQUIB 2ND STEP CIRCUIT
a.

Disconnect the connectors from the center airbag sensor.

U164746E02
5.552,2.333 5.823,2.531 false 0.875,0.979 0.875,0.531 0.875,0.531 0.938,0.531 false 0.885,2.531 0.885,3.188 false 2.521,2.427 2.563,2.385 false 2.521,2.469 2.604,2.385 false 2.521,2.51 2.604,2.427 false 2.5,2.573 2.583,2.49 false 2.552,2.573 2.594,2.531 false 2.521,0.979 2.563,0.938 false 2.51,1.031 2.594,0.948 false 2.51,1.083 2.594,1 false 2.521,1.125 2.604,1.042 false 2.542,1.146 2.583,1.104 false 5.354,1.76 5.01,2.094 false 5.406,1.76 5.802,2.104 false 2.188,2.615 2.333,2.76 0.146,0.146 10 false C 2.083,2.615 2.229,2.76 0.146,0.146 10 false D 1.146,2.615 1.292,2.76 0.146,0.146 10 false E 0.969,2.615 1.115,2.76 0.146,0.146 10 false F 1.271,2.792 2.073,2.958 0.802,0.167 10 false Spiral Cable 2.51,3.135 3.906,3.333 1.396,0.198 10 false Center Airbag Sensor 0.177,3.229 2.094,3.417 1.917,0.188 10 false Driver Side Squib 2nd Step 2.188,1.167 2.333,1.313 0.146,0.146 10 false C 2.073,1.167 2.219,1.313 0.146,0.146 10 false D 1.146,1.167 1.292,1.313 0.146,0.146 10 false E 0.969,1.167 1.115,1.313 0.146,0.146 10 false F 1.271,1.406 2.104,1.604 0.833,0.198 10 false Spiral Cable 2.51,1.458 3.906,1.656 1.396,0.198 10 false Center Airbag Sensor 1,0.469 2.729,0.708 1.729,0.24 10 false Driver Side Squib 2nd Step 0.208,1.76 1.521,2.021 1.313,0.26 12 false w/o Side Airbag: 0.208,0 1.417,0.26 1.208,0.26 12 false w/ Side Airbag: 4.302,0.854 6.604,1.229 2.302,0.375 10 false Front view of wire harness connector: (to Driver Side Squib 2nd Step) 4.677,1.583 5.021,1.771 0.344,0.188 10 false z38 5.698,1.583 6.51,1.729 0.813,0.146 10 false Connector E 5.875,2.479 6.854,2.646 0.979,0.167 10 false Color: Black 2.521,1.188 2.646,1.354 0.125,0.167 10 false B 2.875,0.969 3,1.125 0.125,0.156 10 false A 2.51,2.625 2.656,2.781 0.146,0.156 10 false B 2.885,2.396 3.052,2.563 0.167,0.167 10 false A 5.875,2.031 6,2.188 0.125,0.156 10 false 2 4.927,2.094 5.052,2.25 0.125,0.156 10 false 1


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
z38-1 - Body ground Ignition switch ON Below 1 V
z38-2 - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z38-1 - z38-2 Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z38-1 - z38-2 Always 1 MΩ or higher
z38-1 - Body ground Always 1 MΩ or higher
z38-2 - Body ground Always 1 MΩ or higher




OK

4.CHECK CENTER AIRBAG SENSOR

NG

5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - SPIRAL CABLE)
4.CHECK CENTER AIRBAG SENSOR
a.
C173643E02
1.712,3.334 1.864,3.485 0.151,0.151 10 D 1.83,3.334 1.981,3.485 0.151,0.151 10 C 0.453,3.334 0.604,3.485 0.151,0.151 10 F 0.571,3.334 0.722,3.485 0.151,0.151 10 E 0.719,3.613 1.517,3.773 0.798,0.159 10 Spiral Cable 2.203,3.984 3.151,4.311 0.948,0.328 10 Center Airbag Sensor 0.483,3.947 1.605,4.256 1.123,0.310 10 Driver Side Squib 2nd Step 1.712,1.575 1.864,1.726 0.151,0.151 10 D 1.83,1.575 1.981,1.726 0.151,0.151 10 C 0.453,1.575 0.604,1.726 0.151,0.151 10 F 0.571,1.575 0.722,1.726 0.151,0.151 10 E 0.719,1.854 1.517,2.014 0.798,0.159 10 Spiral Cable 2.203,1.932 3.151,2.260 0.948,0.328 10 Center Airbag Sensor 0.487,0.532 2.490,0.702 2.003,0.170 10 Driver Side Squib 2nd Step 0.357,1.353 0.357,0.612 0.357,0.612 0.463,0.612 false 0.045,2.341 1.340,2.566 1.295,0.225 12 w/o Side Airbag: 0.045,0.002 1.340,0.227 1.295,0.225 12 w/ Side Airbag: 0.335,3.257 0.335,4.031 0.335,4.031 0.451,4.031 false

Connect the connectors to the steering pad and the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1810, B1811, B1812 or B1813 is not output.


HINT:

Codes other than DTC B1810, B1811, B1812 and B1813 may be output at this time, but they are not related to this check.




OK

NG

5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - SPIRAL CABLE)
a.

Restore the released activation prevention mechanism of connector B to its original condition.

U164748E02
5.479,1.938 5.896,2.427 false 5.25,1.938 4.833,2.427 false 2.375,1.104 2.135,1.844 2.135,1.844 2.219,1.844 false 0.771,0.99 0.771,0.49 0.771,0.49 0.865,0.49 false 2.375,2.417 2.375,2.083 2.375,2.083 2.469,2.083 false 0.771,2.521 0.771,3.135 false 2.521,2.344 2.552,2.302 false 2.521,2.396 2.604,2.313 false 2.521,2.448 2.604,2.365 false 2.521,2.5 2.604,2.417 false 2.563,2.51 2.604,2.469 false 2.521,0.896 2.552,0.854 false 2.521,0.948 2.604,0.865 false 2.521,1 2.604,0.917 false 2.521,1.052 2.604,0.969 false 2.563,1.063 2.604,1.021 false 2.521,2.594 2.667,2.74 0.146,0.146 10 false B 2.167,2.594 2.313,2.74 0.146,0.146 10 false C 1.979,2.594 2.125,2.74 0.146,0.146 10 false D 1.031,2.594 1.177,2.74 0.146,0.146 10 false E 0.844,2.594 0.99,2.74 0.146,0.146 10 false F 2.875,2.385 3.042,2.552 0.167,0.167 10 false A 2.51,3.125 3.906,3.302 1.396,0.177 10 false Center Airbag Sensor 1.156,2.813 2.01,2.969 0.854,0.156 10 false Spiral Cable 2.5,2 3.958,2.188 1.458,0.188 10 false Instrument Panel Wire 2.521,1.156 2.667,1.302 0.146,0.146 10 false B 2.167,1.156 2.313,1.302 0.146,0.146 10 false C 1.979,1.156 2.125,1.302 0.146,0.146 10 false D 1.031,1.156 1.177,1.302 0.146,0.146 10 false E 0.844,1.156 0.99,1.302 0.146,0.146 10 false F 2.875,0.938 3.042,1.104 0.167,0.167 10 false A 2.531,1.448 3.927,1.625 1.396,0.177 10 false Center Airbag Sensor 1.156,1.375 2.01,1.531 0.854,0.156 10 false Spiral Cable 2.292,1.76 3.75,1.948 1.458,0.188 10 false Instrument Panel Wire 0.031,1.719 1.375,1.969 1.344,0.25 12 false w/o Side Airbag: 0.031,0.052 1.375,0.302 1.344,0.25 12 false w/ Side Airbag: 4.26,0.719 6.583,1.073 2.323,0.354 10 false Rear view of wire harness connector: (to Spiral Cable) 4.438,1.677 4.76,1.885 0.323,0.208 10 false E13 5.958,1.729 6.792,1.948 0.833,0.219 10 false Connector C 5.802,2.438 6.073,2.656 0.271,0.219 10 false D2- 4.76,2.448 5.083,2.656 0.323,0.208 10 false D2+ 0.896,0.406 2.604,0.625 1.708,0.219 10 false Driver Side Squib 2nd Step 0.063,3.146 1.771,3.365 1.708,0.219 10 false Driver Side Squib 2nd Step


b.

Disconnect the instrument panel wire connector from the spiral cable.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E13-4 (D2+) - Body ground Ignition switch ON Below 1 V
E13-3 (D2-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E13-4 (D2+) - E13-3 (D2-) Always Below 1 Ω



h.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E13-4 (D2+) - E13-3 (D2-) Always 1 MΩ or higher
E13-4 (D2+) - Body ground Always 1 MΩ or higher
E13-3 (D2-) - Body ground Always 1 MΩ or higher




OK

NG

REPLACE INSTRUMENT PANEL WIRE