Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2015.08–2017.08
RM2660E _58 Vehicle Interior _052843 SUPPLEMENTAL RESTRAINT SYSTEMS _0255601 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1661/44  Roll Over Cut Off Indicator Malfunction  


DESCRIPTION

The curtain shield airbag cutoff switch is a mechanism that operates both the right and left sides of the curtain shield airbag and the front seat outer belt when the center airbag sensor detects a roll-over.

The RSCA OFF indicator is installed in the combination meter.

If the curtain shield airbag cutoff switch is operated, the indicator comes on to inform the drive that the roll-over detection system is not working.

The initial setting of the roll-over detection system is on. It automatically operates every time the ignition switch is turned to ON.

DTC Code DTC Detection Condition Trouble Area
B1661/44 When one of the following conditions is met:
·

The center airbag sensor receives an open signal or short to ground in the RSCA OFF indicator circuit.

·

An RSCA OFF indicator malfunction.

·

A center airbag sensor malfunction.


·

Combination meter assembly

·

Curtain shield airbag cutoff switch

·

Center airbag sensor assembly

·

Instrument panel wire

·

No. 3 instrument panel wire



WIRING DIAGRAM

C262835E03
5.761,4.148 6.240,4.309 0.479,0.161 10 RMSW 5.761,1.725 6.156,1.886 0.394,0.161 10 RMIL 5.514,4.061 5.715,4.213 0.201,0.151 10 14 5.476,1.639 5.677,1.790 0.201,0.151 10 15 1.923,4.025 2.041,4.218 0.119,0.193 10 1 3.372,4.025 3.491,4.218 0.119,0.193 10 4 1.74,4.582 2.073,4.753 0.333,0.171 10 G20 1.74,4.744 3.991,4.900 2.251,0.156 10 Curtain Shield Airbag Cutoff Switch 2.099,2.944 2.478,3.115 0.379,0.171 10 E119 2.099,3.106 3.332,3.262 1.233,0.156 10 Combination Meter 2.584,2.34 3.334,2.497 0.750,0.156 10 RSCA OFF 1.028,1.614 1.236,1.797 0.208,0.183 10 21 1.316,1.614 1.453,1.797 0.137,0.183 10 B 3.896,1.614 4.198,1.797 0.302,0.183 10 R/O 4.236,1.614 4.488,1.797 0.253,0.183 10 12 0.198,3.424 1.898,3.605 1.700,0.181 10 from MPX-B NO. 2 Fuse 5.587,5.75 6.984,5.925 1.397,0.174 10 Center Airbag Sensor 3.783,5.381 4.164,5.559 0.381,0.178 10 GE1 3.884,5.168 4.068,5.352 0.183,0.183 10 3 3.783,4.15 4.144,4.340 0.361,0.190 10 GE1 3.884,3.937 4.068,4.121 0.183,0.183 10 4 5.595,5.603 5.900,5.774 0.305,0.171 10 E47

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

After replacing the center airbag sensor assembly, refer to initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK COMBINATION METER (SOURCE VOLTAGE)
a.
U165690E02
1.583,2.052 1.042,2.635 1.042,2.635 0.917,2.635 false 0.26,0.26 2.635,0.948 2.375,0.688 10 false Component with harness connected: (Combination Meter) 0.302,1.896 0.688,2.083 0.385,0.188 10 false E119 0.604,2.573 0.969,2.781 0.365,0.208 10 false R/O

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Remove the combination meter with the connector connected.


d.

Disconnect the connector from the center airbag sensor.


e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON.


g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E119-12 (R/O) - Body ground Ignition switch ON 11 to 14 V



h.

Turn the ignition switch off.



OK

2.CHECK RSCA OFF INDICATOR CIRCUIT

NG

2.CHECK RSCA OFF INDICATOR CIRCUIT
a.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

U165691E01
0.141,1.968 0.971,2.355 0.829,0.387 10 Combination Meter 1.266,2.014 2.181,2.337 0.915,0.323 10 Center Airbag Sensor 0.575,1.543 0.741,1.717 0.165,0.174 10 D 0.857,1.734 1.002,1.899 0.146,0.165 10 C 1.155,1.734 1.294,1.876 0.138,0.142 10 B 1.434,1.543 1.729,1.782 0.295,0.239 10 A 2.217,0.088 4.564,0.420 2.348,0.332 10 Front view of wire harness connector: (to Combination Meter) 4.758,0.088 7.062,0.475 2.304,0.387 10 Rear view of wire harness connector: (to Center Airbag Sensor) 3.245,0.974 4.076,1.130 0.832,0.156 10 Connector E 5.458,0.829 6.290,0.985 0.832,0.156 10 Connector B 2.41,1.614 2.788,1.798 0.378,0.184 10 E119 5.005,1.389 5.281,1.573 0.276,0.184 10 E47 3.855,2.118 4.209,2.303 0.354,0.185 10 R/O 6.044,2.357 6.440,2.513 0.397,0.156 10 RMIL 3.756,1.719 3.947,2.101 false 5.892,1.566 6.213,2.352 false 0.112,0.647 0.834,0.996 0.722,0.349 10 Instrument Panel Wire 1.061,1.563 1.061,0.721 1.061,0.721 0.823,0.721 false


b.

Disconnect the connector from the combination meter.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E119-12 (R/O) - Body ground Ignition switch ON Below 1 V



f.

Turn the ignition switch off.


g.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E119-12 (R/O) - E47-15 (RMIL) Always Below 1 Ω
E119-12 (R/O) - Body ground Always 1 MΩ or higher




OK

3.INSPECT CURTAIN SHIELD AIRBAG CUTOFF SWITCH

NG

REPLACE INSTRUMENT PANEL WIRE

3.INSPECT CURTAIN SHIELD AIRBAG CUTOFF SWITCH
a.

Remove the curtain shield airbag cutoff switch (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CURTAIN SHIELD AIRBAG CUTOFF SWITCH>REMOVAL).


b.


OK

4.CHECK CURTAIN SHIELD AIRBAG CUTOFF SWITCH CIRCUIT

NG

4.CHECK CURTAIN SHIELD AIRBAG CUTOFF SWITCH CIRCUIT
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

U165692E01
2.346,0.037 4.693,0.572 2.347,0.536 10 Front view of wire harness connector: (to Curtain Shield Airbag Cutoff Switch) 4.809,0.037 7.114,0.572 2.304,0.536 10 Rear view of wire harness connector: (to Center Airbag Sensor) 3.263,0.988 4.094,1.143 0.832,0.156 10 Connector E 5.432,0.848 6.264,1.004 0.832,0.156 10 Connector B 2.8,1.59 3.158,1.808 0.357,0.218 10 G20 4.903,1.491 5.179,1.675 0.276,0.184 10 E47 6.154,2.237 6.655,2.393 0.501,0.156 10 RMSW 5.962,1.623 6.314,2.215 false 0.171,1.895 1.103,2.391 0.932,0.496 10 Curtain Shield Airbag Cutoff Switch 1.492,1.893 2.407,2.216 0.915,0.323 10 Center Airbag Sensor 0.541,1.459 0.706,1.634 0.165,0.174 10 F 1.145,1.655 1.431,1.913 0.286,0.258 10 C 1.398,1.655 1.637,1.913 0.239,0.258 10 B 0.813,1.655 0.952,1.837 0.140,0.181 10 E 1.048,1.655 1.287,1.913 0.239,0.258 10 D 1.677,1.46 1.972,1.700 0.295,0.239 10 A


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G20-4 - Body ground Ignition switch ON Below 1 V
G20-1 - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E47-14 (RMSW) - G20-4 Always Below 1 Ω
G20-4 - Body ground Always 1 MΩ or higher
G20-1 - Body ground Always Below 1 Ω




OK

NG

5.CHECK INSTRUMENT PANEL WIRE (INSTRUMENT PANEL WIRE - NO. 3 INSTRUMENT PANEL WIRE AND BODY GROUND)
5.CHECK INSTRUMENT PANEL WIRE (INSTRUMENT PANEL WIRE - NO. 3 INSTRUMENT PANEL WIRE AND BODY GROUND)
a.

Disconnect the instrument panel wire connector from the No. 3 instrument panel wire.

U165693E01
0.018,1.88 0.973,2.381 0.955,0.500 10 Curtain Shield Airbag Cutoff Switch 1.597,1.96 2.512,2.283 0.915,0.323 10 Center Airbag Sensor 0.538,1.5 0.703,1.675 0.165,0.174 10 F 1.244,1.675 1.529,1.933 0.286,0.258 10 C 1.517,1.675 1.756,1.933 0.239,0.258 10 B 0.816,1.675 0.977,1.864 0.161,0.188 10 E 1.087,1.675 1.326,1.933 0.239,0.258 10 D 1.783,1.509 2.077,1.748 0.295,0.239 10 A 2.361,0.012 4.709,0.387 2.347,0.375 10 Front view of wire harness connector: (to No. 3 Instrument Panel Wire) 4.783,0.012 7.142,0.372 2.359,0.360 10 Front view of wire harness connector: (to Center Airbag Sensor) 3.261,0.988 4.166,1.187 0.906,0.199 10 Connector C 5.414,0.83 6.367,1.050 0.954,0.220 10 Connector B 2.624,1.582 2.967,1.780 0.344,0.198 10 GE1 4.859,1.323 5.214,1.506 0.355,0.184 10 E47 1.533,0.484 2.274,0.820 0.740,0.336 10 Instrument Panel Wire 1.195,0.423 1.29,0.423 1.29,0.423 1.015,1.515 false 0.099,0.337 1.172,0.673 1.074,0.336 10 No. 3 Instrument Panel Wire 1.499,0.542 1.453,0.542 1.453,0.542 1.385,1.522 false 6.258,2.089 7.089,2.245 0.832,0.156 10 RMSW 5.94,1.577 6.236,2.158 false


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
GE1-4 - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E47-14 (RMSW) - GE1-4 Always Below 1 Ω
GE1-4 - Body ground Always 1 MΩ or higher




OK

REPLACE NO. 3 INSTRUMENT PANEL WIRE

NG

REPLACE INSTRUMENT PANEL WIRE