Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052843 SUPPLEMENTAL RESTRAINT SYSTEMS _0255601 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1638/82  Rear Airbag Sensor Assembly LH Initialization Incomplete  B1693/81  Door Side Airbag Sensor RH Initialization Incomplete  


DESCRIPTION

HINT:

"Door side airbag sensor RH" refer to the side airbag sensor RH.


·

The circuit for the side collision sensor LH or RH (to determine deployment of the front seat airbag LH or RH, rear seat side airbag LH or RH and curtain shield airbag LH or RH) is composed of the center airbag sensor, side airbag sensor LH or RH, and rear airbag sensor LH or RH.

The side airbag sensor LH or RH and rear airbag sensor LH or RH detect impacts to the vehicle and send signals to the center airbag sensor to determine if the airbag should be deployed.

DTC B1693/81 is stored when a malfunction is detected in the circuit for the side collision sensor LH or RH (to determine deployment of the front seat airbag LH or RH and curtain shield airbag LH or RH).

DTC B1638/82 is stored when a malfunction is detected in the circuit for the rear collision sensor LH or RH (to determine deployment of the rear seat side airbag LH or RH and curtain shield airbag LH or RH).


DTC Code DTC Detection Condition Trouble Area
B1638/82 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the circuit for the rear collision sensor LH (to determine deployment of the rear side seat airbag LH and curtain shield airbag LH) for 2 seconds.

·

A rear airbag sensor LH malfunction.

·

A side airbag sensor LH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Rear airbag sensor LH

·

Side airbag sensor LH

·

Center airbag sensor assembly


B1693/81 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the circuit for the side collision sensor RH (to determine deployment of the front seat airbag RH and curtain shield airbag RH) for 2 seconds.

·

A side airbag sensor RH malfunction.

·

A rear airbag sensor RH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Front door wire RH

·

Side airbag sensor RH

·

Rear airbag sensor RH

·

Center airbag sensor assembly



WIRING DIAGRAM

C175144E02
1.198,0.988 1.624,1.158 0.427,0.170 10 BBR+ 0.1,0.009 1.189,0.253 1.089,0.244 12 for RH Side: 1.71,0.898 1.873,1.068 0.163,0.170 10 4 5.432,0.898 5.636,1.068 0.204,0.170 10 17 5.432,1.706 5.636,1.876 0.204,0.170 10 18 1.71,1.697 1.873,1.866 0.163,0.170 10 3 3.456,0.757 3.619,0.926 0.163,0.170 10 4 3.456,1.555 3.619,1.725 0.163,0.170 10 3 1.71,3.083 1.873,3.253 0.163,0.170 10 1 3.671,3.083 3.834,3.253 0.163,0.170 10 2 1.71,3.868 1.873,4.038 0.163,0.170 10 2 3.677,3.868 3.840,4.038 0.163,0.170 10 1 2.617,2.947 2.780,3.117 0.163,0.170 10 2 2.623,3.732 2.786,3.902 0.163,0.170 10 1 1.198,1.787 1.624,1.956 0.427,0.170 10 BBR- 3.415,0.986 3.684,1.156 0.269,0.170 10 IL1 3.415,1.77 3.684,1.940 0.269,0.170 10 IL1 2.582,3.182 2.852,3.352 0.269,0.170 10 IL1 2.582,3.967 2.852,4.136 0.269,0.170 10 IL1 5.718,0.988 6.145,1.158 0.427,0.170 10 BBR+ 5.718,1.787 6.145,1.956 0.427,0.170 10 BBR- 1.198,3.192 1.624,3.362 0.427,0.170 10 BCR+ 0.551,4.679 0.797,4.849 0.246,0.170 10 I9 0.544,4.847 2.359,5.017 1.816,0.170 10 Side Airbag Sensor RH 3.764,4.679 4.073,4.849 0.309,0.170 10 L18 3.757,4.847 5.302,5.017 1.545,0.170 10 Rear Airbag Sensor RH 5.585,4.679 5.894,4.849 0.309,0.170 10 L27 5.578,4.847 6.975,5.017 1.397,0.170 10 Center Airbag Sensor 3.902,3.192 4.328,3.362 0.427,0.170 10 BCR+ 1.198,3.962 1.624,4.132 0.427,0.170 10 BCR- 3.916,3.962 4.342,4.132 0.427,0.170 10 BCR-

C175145E02
1.183,0.99 1.610,1.159 0.427,0.170 10 BBL+ 0.084,0.029 1.094,0.199 1.010,0.170 12 for LH Side: 1.695,0.899 1.858,1.069 0.163,0.170 10 4 5.417,0.899 5.622,1.069 0.204,0.170 10 24 5.417,1.707 5.622,1.877 0.204,0.170 10 23 1.695,1.698 1.858,1.868 0.163,0.170 10 3 1.695,3.085 1.858,3.255 0.163,0.170 10 1 3.657,3.085 3.820,3.255 0.163,0.170 10 2 1.695,3.869 1.858,4.039 0.163,0.170 10 2 3.663,3.869 3.826,4.039 0.163,0.170 10 1 2.697,2.945 2.860,3.115 0.163,0.170 10 2 2.703,3.729 2.866,3.899 0.163,0.170 10 1 1.183,1.788 1.610,1.958 0.427,0.170 10 BBL- 5.685,0.99 6.112,1.159 0.427,0.170 10 BBL+ 5.685,1.788 6.112,1.958 0.427,0.170 10 BBL- 1.183,3.193 1.610,3.363 0.427,0.170 10 BCL+ 0.536,4.681 0.782,4.851 0.246,0.170 10 K7 0.529,4.849 2.058,5.019 1.529,0.170 10 Rear Airbag Sensor LH 3.714,4.681 4.023,4.851 0.309,0.170 10 I19 3.693,4.849 5.218,5.019 1.525,0.170 10 Side Airbag Sensor LH 5.571,4.681 5.879,4.851 0.309,0.170 10 K27 5.564,4.849 6.960,5.019 1.397,0.170 10 Center Airbag Sensor 3.887,3.193 4.314,3.363 0.427,0.170 10 BCL+ 2.648,3.193 2.901,3.363 0.253,0.170 10 IK1 2.648,3.971 2.901,4.141 0.253,0.170 10 IK1 1.183,3.964 1.610,4.134 0.427,0.170 10 BCL- 3.901,3.964 4.328,4.134 0.427,0.170 10 BCL-

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK PAST DTC
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1637 or B1692 is output A
DTC B1632 or B1697 is output B
DTC B1632, B1637, B1692 and B1697 are not output C



C

2.CHECK FOR DTC

A

B

2.CHECK FOR DTC
a.

Turn the ignition switch off.

HINT:

If a communication error occurs, DTCs for both the LH and RH sides will be stored simultaneously. The malfunctioning area can be identified by turning the ignition switch off and then to ON again.



b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


c.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1638 and B1693 are not output A
DTC B1638 is output B
DTC B1693 is output C


HINT:

Codes other than DTC B1638 and B1693 may be output at this time, but they are not related to this check.



C

3.CHECK CONNECTION OF CONNECTORS

A

B

13.CHECK CONNECTION OF CONNECTORS
3.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and side airbag sensor RH.

OK:

The connectors are properly connected.




OK

4.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

4.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and side airbag sensor RH.


b.

Check that the connectors (on the center airbag sensor side and side airbag sensor RH side) are not damaged.

OK:

The connectors are not deformed or damaged.




OK

5.CHECK SIDE AIRBAG SENSOR RH CIRCUIT

NG

REPLACE HARNESS AND CONNECTOR

5.CHECK SIDE AIRBAG SENSOR RH CIRCUIT
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

U164805E01
0.042,1.884 0.805,2.257 0.763,0.373 10 Side Airbag Sensor RH 1.57,1.717 2.495,2.067 0.924,0.350 10 Center Airbag Sensor 0.514,1.456 0.669,1.621 0.156,0.165 10 F 1.163,1.638 1.314,1.789 0.151,0.151 10 C 1.058,1.638 1.209,1.789 0.151,0.151 10 D 0.848,1.638 0.999,1.789 0.151,0.151 10 E 1.358,1.635 1.495,1.786 0.137,0.151 10 B 1.714,1.451 1.847,1.625 0.133,0.174 10 A 2.381,0.198 4.792,0.785 2.410,0.587 10 Rear view of wire harness connector: (to Side Airbag Sensor RH) 4.829,0.198 7.156,0.785 2.327,0.587 10 Rear view of wire harness connector: (to Center Airbag Sensor) 3.736,1.647 4.565,1.817 0.830,0.170 10 Connector E 6.299,1.65 7.129,1.820 0.830,0.170 10 Connector B 2.689,1.325 2.907,1.495 0.218,0.170 10 I9 4.878,1.248 5.131,1.418 0.253,0.170 10 L27 2.692,2.172 3.105,2.321 0.413,0.149 10 BBR+ 3.584,2.168 3.997,2.317 0.413,0.149 10 BBR- 6.494,2.004 6.906,2.153 0.413,0.149 10 BBR+ 4.705,2.032 5.118,2.181 0.413,0.149 10 BBR- 5.546,2.383 6.375,2.545 0.830,0.163 10 Service Wire 3.218,1.673 2.881,2.144 false 3.288,1.673 3.652,2.144 false 5.881,1.774 5.068,2.103 false 6.021,1.767 6.468,2.063 false 5.945,2.177 5.945,2.373 false


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I9-4 (BBR+) - Body ground Ignition switch ON Below 1 V
I9-3 (BBR-) - Body ground Ignition switch ON Below 1 V



c.

Turn the ignition switch off.


d.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


e.

Using a service wire, connect terminals 17 (BBR+) and 18 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I9-4 (BBR+) - I9-3 (BBR-) Always Below 1 Ω



g.

Disconnect the service wire from connector B.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I9-4 (BBR+) - I9-3 (BBR-) Always 1 MΩ or higher
I9-4 (BBR+) - Body ground Always 1 MΩ or higher
I9-3 (BBR-) - Body ground Always 1 MΩ or higher




OK

6.CHECK CONNECTION OF CONNECTORS

NG

11.CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT DOOR WIRE RH)
6.CHECK CONNECTION OF CONNECTORS
a.

Check that the connector is properly connected to the rear airbag sensor RH.

OK:

The connector is properly connected.




OK

7.CHECK CONNECTORS

NG

CONNECT CONNECTOR PROPERLY

7.CHECK CONNECTORS
a.

Disconnect the connectors from the side airbag sensor RH and rear airbag sensor RH.


b.

Check that the connector (on the rear airbag sensor RH side) is not damaged.

OK:

The connector is not deformed or damaged.




OK

8.CHECK REAR AIRBAG SENSOR RH CIRCUIT

NG

REPLACE HARNESS AND CONNECTOR

8.CHECK REAR AIRBAG SENSOR RH CIRCUIT
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

U164803E01
0.122,1.528 0.931,1.883 0.809,0.355 10 Rear Airbag Sensor RH 1.547,1.528 2.351,1.883 0.804,0.355 10 Side Airbag Sensor RH 1.752,1.084 1.876,1.254 0.123,0.170 10 A 0.594,1.052 0.718,1.221 0.123,0.170 10 F 1.425,1.29 1.549,1.460 0.123,0.170 10 B 1.248,1.29 1.371,1.460 0.123,0.170 10 C 1.136,1.29 1.259,1.460 0.123,0.170 10 D 0.935,1.29 1.059,1.460 0.123,0.170 10 E 4.898,1.402 5.040,1.572 0.142,0.170 10 I9 2.711,1.402 2.966,1.572 0.255,0.170 10 L18 2.378,0.365 4.705,0.716 2.327,0.350 10 Front view of wire harness connector: (to Rear Airbag Sensor RH) 4.83,0.365 7.157,0.716 2.327,0.350 10 Rear view of wire harness connector: (to Side Airbag Sensor RH) 4.047,1.655 4.859,1.839 0.812,0.184 10 Connector E 6.127,1.655 6.939,1.839 0.812,0.184 10 Connector B 4.114,1.953 4.535,2.137 0.421,0.184 10 BCR+ 4.945,2.219 5.319,2.403 0.375,0.184 10 BCR- 2.818,2.079 3.238,2.249 0.420,0.170 10 BCR- 6.101,2.247 6.520,2.417 0.420,0.170 10 BCR+ 3.769,2.359 4.598,2.512 0.829,0.152 10 Service Wire 3.493,1.731 3.078,2.044 false 3.661,1.724 4.081,2.016 false 3.664,2.059 4.084,2.351 false 5.688,1.797 5.125,2.194 false 5.792,1.794 6.199,2.226 false


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I9-1 (BCR+) - Body ground Ignition switch ON Below 1 V
I9-2 (BCR-) - Body ground Ignition switch ON Below 1 V



c.

Turn the ignition switch off.


d.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


e.

Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I9-1 (BCR+) - I9-2 (BCR-) Always Below 1 Ω



g.

Disconnect the service wire from connector E.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I9-1 (BCR+) - I9-2 (BCR-) Always 1 MΩ or higher
I9-1 (BCR+) - Body ground Always 1 MΩ or higher
I9-2 (BCR-) - Body ground Always 1 MΩ or higher




OK

9.CHECK SIDE AIRBAG SENSOR RH

NG

12.CHECK FRONT DOOR WIRE RH (SIDE AIRBAG SENSOR RH - NO. 2 FLOOR WIRE)
9.CHECK SIDE AIRBAG SENSOR RH
a.
C171827E11
0.603,1.435 1.340,1.750 0.737,0.316 10 Side Airbag Sensor LH 2.127,1.209 3.075,1.525 0.948,0.316 10 Center Airbag Sensor

Connect the connector to the center airbag sensor.


b.

Interchange the side airbag sensor RH with LH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1693 and B1698 are not output A
DTC B1698 is output B
DTC B1693 is output C

HINT:

Codes other than DTC B1693 and B1698 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


k.

Return the side airbag sensor LH and RH to their original positions and connect the connectors to them.



C

10.CHECK REAR AIRBAG SENSOR RH

A

B

10.CHECK REAR AIRBAG SENSOR RH
a.
C171828E01
0.469,1.174 1.236,1.545 0.767,0.371 10 Rear Airbag Sensor RH 2.141,1.174 2.894,1.524 0.753,0.350 10 Side Airbag Sensor RH

Temporarily replace the rear airbag sensor RH with a new one.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1693 is not output.


HINT:

Codes other than DTC B1693 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.



OK

NG

11.CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT DOOR WIRE RH)
a.

Disconnect the No. 2 floor wire from the front door wire RH.

U164807E02
3.198,1.844 2.771,2.135 false 3.427,1.833 3.771,2.146 false 0.979,1.49 0.979,0.448 0.979,0.448 0.865,0.448 false 1.406,1.49 1.406,0.396 1.406,0.396 1.49,0.396 false 6.021,1.771 6.292,2.063 false 5.958,2.167 5.958,2.302 false 5.885,1.771 5.323,2.146 false 0.156,0.344 0.875,0.708 0.719,0.365 10 false Front Door Wire RH 1.521,0.302 2.26,0.656 0.74,0.354 10 false No. 2 Floor Wire 1.688,1.729 2.594,2.104 0.906,0.375 10 false Center Airbag Sensor 0.063,1.865 0.833,2.24 0.771,0.375 10 false Side Airbag Sensor RH 1.781,1.458 1.927,1.615 0.146,0.156 10 false A 1.521,1.656 1.667,1.813 0.146,0.156 10 false B 1.219,1.656 1.365,1.813 0.146,0.156 10 false C 1.104,1.656 1.25,1.813 0.146,0.156 10 false D 0.792,1.656 0.938,1.813 0.146,0.156 10 false E 0.521,1.458 0.667,1.615 0.146,0.156 10 false F 2.479,0.229 4.813,0.573 2.333,0.344 10 false Front view of wire harness connector: (to Front Door Wire RH) 4.823,0.229 7.146,0.573 2.323,0.344 10 false Rear view of wire harness connector: (to Center Airbag Sensor) 2.677,1.365 2.896,1.521 0.219,0.156 10 false IL1 2.583,2.146 2.99,2.302 0.406,0.156 10 false BBR+ 6.323,2 6.729,2.156 0.406,0.156 10 false BBR+ 3.677,2.146 4.083,2.302 0.406,0.156 10 false BBR- 5.135,2.146 5.542,2.302 0.406,0.156 10 false BBR- 5.896,2.313 6.719,2.479 0.823,0.167 10 false Service Wire 3.75,1.552 4.604,1.708 0.854,0.156 10 false Connector C 6.219,1.552 7.073,1.708 0.854,0.156 10 false Connector B 4.813,1.229 5.104,1.396 0.292,0.167 10 false L27


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
IL1-4 (BBR+) - Body ground Ignition switch ON Below 1 V
IL1-3 (BBR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 17 (BBR+) and 18 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IL1-4 (BBR+) - IL1-3 (BBR-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IL1-4 (BBR+) - IL1-3 (BBR-) Always 1 MΩ or higher
IL1-4 (BBR+) - Body ground Always 1 MΩ or higher
IL1-3 (BBR-) - Body ground Always 1 MΩ or higher




OK

REPLACE FRONT DOOR WIRE RH

NG

REPLACE NO. 2 FLOOR WIRE

12.CHECK FRONT DOOR WIRE RH (SIDE AIRBAG SENSOR RH - NO. 2 FLOOR WIRE)
a.

Disconnect the front door wire RH from the No. 2 floor wire.

U164668E02
3.125,1.927 2.823,2.26 false 3.323,1.927 3.646,2.24 false 3.26,2.219 3.51,2.479 false 5.688,1.771 5.125,2.125 false 5.771,1.771 6.188,2.198 false 0.979,1.094 0.979,0.135 0.979,0.135 0.865,0.135 false 1.406,1.073 1.406,0.094 1.406,0.094 1.469,0.094 false 0.115,0.063 0.823,0.375 0.708,0.313 10 false No. 2 Floor Wire 1.531,0.052 2.292,0.375 0.76,0.323 10 false Front Door Wire RH 0.063,1.542 0.854,1.906 0.792,0.365 10 false Rear Airbag Sensor RH 1.635,1.552 2.469,1.906 0.833,0.354 10 false Side Airbag Sensor RH 1.802,1.063 1.938,1.229 0.135,0.167 10 false A 0.5,1.083 0.635,1.25 0.135,0.167 10 false F 1.531,1.26 1.667,1.427 0.135,0.167 10 false B 1.229,1.271 1.365,1.438 0.135,0.167 10 false C 1.094,1.271 1.229,1.438 0.135,0.167 10 false D 0.792,1.271 0.927,1.438 0.135,0.167 10 false E 2.552,1.281 2.844,1.458 0.292,0.177 10 false IL1 2.385,0.24 4.813,0.583 2.427,0.344 10 false Front view of wire harness connector: (to No. 2 Floor Wire) 4.813,0.24 7.146,0.583 2.333,0.344 10 false Rear view of wire harness connector: (to Side Airbag Sensor RH) 3.656,1.625 4.552,1.813 0.896,0.188 10 false Connector C 4.99,1.281 5.219,1.458 0.229,0.177 10 false I9 6.104,1.625 7,1.813 0.896,0.188 10 false Connector B 3.708,2.198 4.125,2.354 0.417,0.156 10 false BCR+ 4.813,2.125 5.229,2.281 0.417,0.156 10 false BCR- 2.396,2.198 2.813,2.354 0.417,0.156 10 false BCR- 6.177,2.198 6.594,2.354 0.417,0.156 10 false BCR+ 3.479,2.5 4.323,2.677 0.844,0.177 10 false Service Wire


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I9-1 (BCR+) - Body ground Ignition switch ON Below 1 V
I9-2 (BCR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I9-1 (BCR+) - I9-2 (BCR-) Always Below 1 Ω



h.

Disconnect the service wire from connector C.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I9-1 (BCR+) - I9-2 (BCR-) Always 1 MΩ or higher
I9-1 (BCR+) - Body ground Always 1 MΩ or higher
I9-2 (BCR-) - Body ground Always 1 MΩ or higher




OK

REPLACE NO. 2 FLOOR WIRE

NG

REPLACE FRONT DOOR WIRE RH

13.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and rear airbag sensor LH.

OK:

The connectors are properly connected.




OK

14.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

14.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and rear airbag sensor LH.


b.

Check that the connectors (on the center airbag sensor side and rear airbag sensor LH side) are not damaged.

OK:

The connectors are not deformed or damaged.




OK

15.CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - REAR AIRBAG SENSOR LH)

NG

REPLACE FLOOR WIRE

15.CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - REAR AIRBAG SENSOR LH)
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

U164509E01
0.059,1.631 0.854,2.019 0.795,0.387 10 Rear Airbag Sensor LH 1.404,1.93 2.320,2.253 0.915,0.323 10 Center Airbag Sensor 0.517,1.178 0.682,1.353 0.165,0.174 10 D 0.853,1.389 1.139,1.646 0.286,0.258 10 C 1.171,1.379 1.410,1.637 0.239,0.258 10 B 1.535,1.164 1.830,1.404 0.295,0.239 10 A 0.416,0.408 1.122,0.582 0.707,0.174 10 Floor Wire 2.299,0.284 4.603,0.820 2.304,0.536 10 Rear view of wire harness connector: (to Rear Airbag Sensor LH) 4.839,0.284 7.143,0.820 2.304,0.536 10 Rear view of wire harness connector: (to Center Airbag Sensor) 1.124,0.483 1.32,0.483 1.32,0.483 1.066,1.191 false 3.758,1.616 4.590,1.772 0.832,0.156 10 Connector C 6.324,1.656 7.156,1.812 0.832,0.156 10 Connector B 2.589,1.417 2.883,1.600 0.295,0.184 10 K7 4.935,1.395 5.229,1.579 0.295,0.184 10 K27 2.517,1.864 2.914,2.020 0.397,0.156 10 BBL+ 2.759,2.453 3.155,2.609 0.397,0.156 10 BBL- 4.698,2.012 5.095,2.168 0.397,0.156 10 BBL+ 6.179,2.268 6.575,2.424 0.397,0.156 10 BBL- 4.319,2.379 5.187,2.572 0.869,0.193 10 Service Wire 3.216,1.835 2.88,1.933 false 3.277,1.836 2.992,2.427 false 5.374,2.313 5.131,2.444 false 5.442,1.934 5.066,2.067 false 5.573,1.936 6.156,2.318 false


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K7-4 (BBL+) - Body ground Ignition switch ON Below 1 V
K7-3 (BBL-) - Body ground Ignition switch ON Below 1 V



c.

Turn the ignition switch off.


d.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


e.

Using a service wire, connect terminals 24 (BBL+) and 23 (BBL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K7-4 (BBL+) - K7-3 (BBL-) Always Below 1 Ω



g.

Disconnect the service wire from connector B.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K7-4 (BBL+) - K7-3 (BBL-) Always 1 MΩ or higher
K7-4 (BBL+) - Body ground Always 1 MΩ or higher
K7-3 (BBL-) - Body ground Always 1 MΩ or higher




OK

16.CHECK CONNECTION OF CONNECTOR

NG

REPLACE FLOOR WIRE

16.CHECK CONNECTION OF CONNECTOR
a.

Check that the connector is properly connected to the side airbag sensor LH.

OK:

The connector is properly connected.




OK

17.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

17.CHECK CONNECTORS
a.

Disconnect the connectors from the rear airbag sensor LH and side airbag sensor LH.


b.

Check that the connector (on the side airbag sensor LH side) is not damaged.

OK:

The connector is not deformed or damaged.




OK

18.CHECK SIDE AIRBAG SENSOR LH CIRCUIT

NG

REPLACE HARNESS AND CONNECTOR

18.CHECK SIDE AIRBAG SENSOR LH CIRCUIT
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

U164659E01
0.112,1.48 0.886,1.851 0.774,0.371 10 Side Airbag Sensor LH 1.398,1.231 1.514,1.401 0.116,0.170 10 B 1.213,1.231 1.353,1.401 0.140,0.170 10 C 1.115,1.231 1.255,1.401 0.140,0.170 10 D 0.93,1.231 1.071,1.401 0.140,0.170 10 E 0.612,1.044 0.753,1.214 0.140,0.170 10 F 1.713,1.045 1.917,1.250 0.205,0.205 10 A 1.542,1.466 2.346,1.816 0.804,0.350 10 Rear Airbag Sensor LH 2.347,0.312 4.704,0.621 2.357,0.309 10 Rear view of wire harness connector: (to Side Airbag Sensor LH) 4.842,0.312 7.150,0.621 2.309,0.309 10 Rear view of wire harness connector: (to Rear Airbag Sensor LH) 3.681,1.51 4.552,1.680 0.871,0.170 10 Connector E 6.154,1.559 7.025,1.729 0.871,0.170 10 Connector B 2.539,1.172 2.840,1.335 0.302,0.163 10 I19 4.96,1.196 5.262,1.359 0.302,0.163 10 K7 2.505,2.259 2.939,2.442 0.434,0.184 10 BCL+ 3.794,2.108 4.228,2.291 0.434,0.184 10 BCL- 6.084,2.334 6.518,2.517 0.434,0.184 10 BCL+ 5.166,2.36 5.600,2.544 0.434,0.184 10 BCL- 3.099,1.786 2.751,2.238 false 3.195,1.782 3.766,2.164 false 3.401,2.421 4.244,2.591 0.843,0.170 10 Service Wire 3.233,2.071 3.485,2.4 false 5.706,1.771 5.376,2.346 false 5.776,1.772 6.196,2.313 false


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K7-1 (BCL+) - Body ground Ignition switch ON Below 1 V
K7-2 (BCL-) - Body ground Ignition switch ON Below 1 V



c.

Turn the ignition switch off.


d.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


e.

Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K7-1 (BCL+) - K7-2 (BCL-) Always Below 1 Ω



g.

Disconnect the service wire from connector E.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K7-1 (BCL+) - K7-2 (BCL-) Always 1 MΩ or higher
K7-1 (BCL+) - Body ground Always 1 MΩ or higher
K7-2 (BCL-) - Body ground Always 1 MΩ or higher




OK

19.CHECK REAR AIRBAG SENSOR LH

NG

21.CHECK FLOOR WIRE (REAR AIRBAG SENSOR LH - FRONT DOOR WIRE LH)
19.CHECK REAR AIRBAG SENSOR LH
a.
C146229E19
0.399,1.727 1.936,1.892 1.536,0.165 10 Rear Airbag Sensor LH 1.482,1.263 2.852,1.428 1.371,0.165 10 Center Airbag Sensor 0.915,0.894 0.915,1.704 false

Temporarily replace the side airbag sensor LH with a new one.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1638 is not output.


HINT:

Codes other than DTC B1638 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.



OK

NG

20.CHECK SIDE AIRBAG SENSOR LH
20.CHECK SIDE AIRBAG SENSOR LH
a.
C171828E12
0.421,1.174 1.197,1.545 0.776,0.371 10 Side Airbag Sensor RH 2.141,1.174 3.018,1.524 0.877,0.350 10 Rear Airbag Sensor LH

Interchange the side airbag sensor LH with LRH and connect the connectors to them.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 90 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1638 is output A
DTC B1633 is output B
DTC B1633 and B1638 are not output C

HINT:

Codes other than DTC B1633 and B1638 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


j.

Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.



C

A

B

21.CHECK FLOOR WIRE (REAR AIRBAG SENSOR LH - FRONT DOOR WIRE LH)
a.

Disconnect the floor wire from the front door wire LH.

U164669E02
3.104,1.698 2.823,2.271 false 3.333,1.708 3.771,2.104 false 3.292,2.188 3.51,2.5 false 5.688,1.781 5.125,2.135 false 5.802,1.771 6.219,2.198 false 0.979,1.083 0.979,0.125 0.979,0.125 0.865,0.125 false 1.417,1.094 1.417,0.125 1.417,0.125 1.479,0.125 false 0.156,0.052 0.865,0.365 0.708,0.313 10 false Front Door Wire LH 1.563,0.052 2.271,0.25 0.708,0.198 10 false Floor Wire 0.063,1.552 0.854,1.917 0.792,0.365 10 false Side Airbag Sensor LH 1.552,1.563 2.479,1.917 0.927,0.354 10 false Rear Airbag Sensor LH 1.802,1.073 1.938,1.24 0.135,0.167 10 false A 0.5,1.063 0.635,1.229 0.135,0.167 10 false F 1.542,1.26 1.677,1.427 0.135,0.167 10 false B 1.229,1.26 1.365,1.427 0.135,0.167 10 false C 1.094,1.26 1.229,1.427 0.135,0.167 10 false D 0.792,1.26 0.927,1.427 0.135,0.167 10 false E 2.542,1.281 2.833,1.458 0.292,0.177 10 false IK1 2.313,0.26 4.667,0.604 2.354,0.344 10 false Front view of wire harness connector: (to Front Door Wire LH) 4.813,0.26 7.146,0.604 2.333,0.344 10 false Rear view of wire harness connector: (to Rear Airbag Sensor LH) 3.656,1.646 4.552,1.833 0.896,0.188 10 false Connector C 4.948,1.281 5.177,1.458 0.229,0.177 10 false K7 6.104,1.646 7,1.833 0.896,0.188 10 false Connector B 3.813,2.094 4.229,2.25 0.417,0.156 10 false BCL- 4.813,2.135 5.229,2.292 0.417,0.156 10 false BCL- 2.396,2.208 2.813,2.365 0.417,0.156 10 false BCL+ 6.177,2.208 6.594,2.365 0.417,0.156 10 false BCL+ 3.479,2.51 4.323,2.688 0.844,0.177 10 false Service Wire


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K7-1 (BCL+) - Body ground Ignition switch ON Below 1 V
K7-2 (BCL-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K7-1 (BCL+) - K7-2 (BCL-) Always Below 1 Ω



h.

Disconnect the service wire from connector C.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K7-1 (BCL+) - K7-2 (BCL-) Always 1 MΩ or higher
K7-1 (BCL+) - Body ground Always 1 MΩ or higher
K7-2 (BCL-) - Body ground Always 1 MΩ or higher




OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE FLOOR WIRE