Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052844 PRE-CRASH SAFETY _0255621 PRE-CRASH SAFETY SYSTEM J

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  Power Source Circuit  


DESCRIPTION

This circuit supplies power to the seat belt control ECU when the ignition switch is ON.

WIRING DIAGRAM

E149049E02
6.042,3.844 6.854,4.531 0.813,0.688 10 false Seat Belt Control ECU 6.094,1.031 6.323,1.188 0.229,0.156 10 false +B 6.104,2.156 6.396,2.344 0.292,0.188 10 false IG1 6.083,3.073 6.5,3.229 0.417,0.156 10 false PGND 5.667,3.083 5.948,3.24 0.281,0.156 10 false E41 5.667,2.156 5.948,2.313 0.281,0.156 10 false E42 5.677,1.042 5.958,1.198 0.281,0.156 10 false E41 5.771,0.802 5.875,0.979 0.104,0.177 10 false 7 5.771,1.948 5.896,2.115 0.125,0.167 10 false 8 3.667,2.073 3.792,2.24 0.125,0.167 10 false 3 3.667,2.51 3.792,2.677 0.125,0.167 10 false 1 2.76,2.521 2.885,2.688 0.125,0.167 10 false 2 2.76,2.073 2.885,2.229 0.125,0.156 10 false 5 5.781,2.885 5.896,3.042 0.115,0.156 10 false 8 3.833,1.208 4.208,1.375 0.375,0.167 10 false PSB 4.302,2.313 5.229,2.458 0.927,0.146 10 false ECU-IG No. 1 2.927,2.948 3.604,3.135 0.677,0.188 10 false IG1 NO. 1 0.885,2.625 2.302,2.958 1.417,0.333 10 false from Main Body ECU 1.104,1.219 1.552,1.396 0.448,0.177 10 false LH-J/B 0.667,2.073 0.99,2.25 0.323,0.177 10 false ALT

CAUTION / NOTICE / HINT

HINT:

Start the engine before inspection. Check the IG1 NO. 1 relay or battery if the starting system does not start.


PROCEDURE

1.INSPECT FUSE (ECU-IG No. 1, PSB)
a.

Remove the ECU-IG No. 1 and PSB fuses from the main body ECU.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ECU-IG No. 1 fuse Always Below 1 Ω
PSB fuse




OK

2.CHECK HARNESS AND CONNECTOR (SEAT BELT CONTROL ECU - BATTERY AND BODY GROUND)

NG

REPLACE FUSE

2.CHECK HARNESS AND CONNECTOR (SEAT BELT CONTROL ECU - BATTERY AND BODY GROUND)
a.
U165820E02
1.271,2.24 0.823,2.927 true 2.417,2.313 2.625,2.927 true 1.552,2.25 1.813,2.938 true 1.292,0.792 1.74,0.948 0.448,0.156 10 false E41 2.406,0.792 2.854,0.948 0.448,0.156 10 false E42 0.365,0.073 2.604,0.594 2.24,0.521 10 false Rear view of wire harness connector: (to Seat Belt Control ECU) 2.531,2.958 2.781,3.125 0.25,0.167 10 false IG1 0.615,2.958 1.052,3.125 0.438,0.167 10 false PGND 1.771,2.958 1.979,3.125 0.208,0.167 10 false +B

Disconnect the E41 and E42 seat belt control ECU connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E42-8 (IG1) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
E41-7 (+B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E41-8 (PGND) - Body ground Always Below 1 Ω


Result
Result Proceed to
OK
(for LHD)
A
OK
(for RHD)
B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR