Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052844 PRE-CRASH SAFETY _0255621 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  B2075  Passenger Side Seat Belt Buckle Switch Circuit Malfunction  


DESCRIPTION

This DTC is stored when there is a malfunction in the front seat inner belt buckle switch circuit for the passenger side.

DTC Code DTC Detection Condition Trouble Area
B2075 Malfunction in the front seat inner belt (buckle switch) circuit.
·

Harness or connector

·

Front seat inner belt (for passenger side)

·

Seat belt control ECU



WIRING DIAGRAM

E149043E05
4.823,0.635 5.229,0.802 0.406,0.167 10 false PBK+ 4.823,1.719 5.229,1.896 0.406,0.177 10 false PBK- 4.771,2.167 5.177,2.344 0.406,0.177 10 false E41 4.771,2.333 6.208,2.677 1.438,0.344 10 false Seat Belt Control ECU 1.156,2.229 1.563,2.406 0.406,0.177 10 false c24*2 1.156,2.042 1.563,2.219 0.406,0.177 10 false c30*1 0.031,2.146 0.771,2.323 0.74,0.177 10 false *1: for LHD 0.031,2.448 0.771,2.625 0.74,0.177 10 false *2: for RHD 1.156,2.396 3.813,2.74 2.656,0.344 10 false Front Seat Inner Belt (for Passenger Side) 3.188,1.625 3.354,1.792 0.167,0.167 10 false 1 3.188,0.542 3.302,0.698 0.115,0.156 10 false 2 2.979,0.531 3.125,0.698 0.146,0.167 10 false + 2.958,1.625 3.104,1.792 0.146,0.167 10 false E 4.594,0.542 4.74,0.688 0.146,0.146 10 false 5 4.594,1.615 4.74,1.76 0.146,0.146 10 false 6

PROCEDURE

1.CHECK FOR DTC

OK

NG

2.CHECK SEAT BELT CONTROL ECU
2.CHECK SEAT BELT CONTROL ECU
a.
U165819E02
2.438,1.448 2.073,2.031 true 2.552,1.448 2.813,2.031 true 2.854,3.688 3.208,3.833 0.354,0.146 10 false GND 1.906,2.052 2.385,2.229 0.479,0.177 10 false PBK- 2.656,2.052 3.135,2.229 0.479,0.177 10 false PBK+ 0.302,0.073 2.688,0.594 2.385,0.521 10 false Component with harness connected: (Seat Belt Control ECU) 0.125,2.385 2.781,2.646 2.656,0.26 10 false Seat belt is fastened (Buckle switch is on) 2.281,0.823 2.594,1.021 0.313,0.198 10 false E42

Reconnect the E41 seat belt control ECU connector.


b.

Disconnect the c30*1 or c24*2 front seat inner belt connector.

HINT:
·

*1: for LHD

·

*2: for RHD




c.

Use an oscilloscope to check the waveform of the seat belt control ECU between the connector terminals.

Measurement Condition
Tester Connection E41-5 (PBK+) - E41-6 (PBK-)
Tool Setting 5 V/DIV., 20 ms./DIV.
Switch Condition Ignition switch ON
Front passenger side seat belt unfastened (Buckle switch off)
Ignition switch ON
Front passenger side seat belt fastened (Buckle switch on)

OK:

4.5 to 5.5 V


Result
Result Proceed to
OK
(for LHD)
A
OK
(for RHD)
B
NG C



A

B

C

3.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT - SEAT BELT CONTROL ECU)
3.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT - SEAT BELT CONTROL ECU)
a.

Disconnect the c30*1 or c24*2 front seat inner belt connector.

HINT:
·

*1: for LHD

·

*2: for RHD



E349629E01
0.354,0.906 0.698,1.156 0.344,0.25 0.354,1.25 0.698,1.5 0.344,0.25 6.125,0.656 6.469,0.906 0.344,0.25 1.26,1.896 1.479,1.323 true 2.021,1.885 1.802,1.323 true 5.854,2.396 6.146,2.063 true 6.49,2.375 6.24,2.073 true 0.583,0.125 2.979,0.635 2.396,0.51 10 false Front view of wire harness connector: (to Front Seat Inner Belt (for Passenger Side)) 0.417,0.948 0.708,1.198 0.292,0.25 10 false c30 0.417,1.302 0.708,1.552 0.292,0.25 10 false c24 0.76,0.948 1.052,1.198 0.292,0.25 10 false *1 0.771,1.313 1.063,1.563 0.292,0.25 10 false *2 1.208,1.948 1.5,2.198 0.292,0.25 10 false E 2.031,1.938 2.323,2.188 0.292,0.25 10 false + 4.229,0.135 6.646,0.552 2.417,0.417 10 false Rear view of wire harness connector: (to Seat Belt Control ECU) 6.177,0.698 6.469,0.948 0.292,0.25 10 false E41 3.656,2.177 4.521,2.375 0.865,0.198 10 false *1: for LHD 3.656,2.448 4.521,2.646 0.865,0.198 10 false *2: for RHD 5.698,2.417 6.333,2.615 0.635,0.198 10 false PBK+ 6.427,2.417 6.927,2.615 0.5,0.198 10 false PBK-


b.

Disconnect the E41 seat belt control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
c30-2 (+) - E41-5 (PBK+) Always Below 1 Ω
c30-1 (E) - E41-6 (PBK-)
c30-2 (+) or E41-5 (PBK+) - Body ground 1 MΩ higher
c30-1 (E) or E41-6 (PBK-) - Body ground

for RHD
Tester Connection Condition Specified Condition
c24-2 (+) - E41-5 (PBK+) Always Below 1 Ω
c24-1 (E) - E41-6 (PBK-)
c24-2 (+) or E41-5 (PBK+) - Body ground 1 MΩ higher
c24-1 (E) or E41-6 (PBK-) - Body ground



Result
Result Proceed to
OK
(for LHD)
A
OK
(for RHD)
B
NG C


A

REPLACE FRONT SEAT INNER BELT RH (for Passenger Side)

B

REPLACE FRONT SEAT INNER BELT LH (for Passenger Side)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR