Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2015.08
RM2660E _58 Vehicle Interior _052844 PRE-CRASH SAFETY _0255621 PRE-CRASH SAFETY SYSTEM J

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  Pre-crash Safety System Cancel Switch Circuit  


DESCRIPTION

The driving support ECU assembly receives pre-crash safety system cancel on/off signals from the pre-crash system cancel switch assembly.

WIRING DIAGRAM

E240346E21
4.885,2.125 7.031,2.313 2.146,0.188 10 false Driving Support ECU Assembly 4.885,1.969 5.333,2.219 0.448,0.25 10 false E164 5.365,1.052 6.219,1.302 0.854,0.25 10 false PBSW 2.156,1.615 4.313,2 2.156,0.385 10 false Pre-Crash Safety System Cancel Switch Assembly 2.156,1.458 2.594,1.635 0.438,0.177 10 false E170 3.417,0.969 3.833,1.24 0.417,0.271 10 false ECU 3.802,0.948 4.052,1.219 0.25,0.271 10 false 8 2.323,0.958 2.531,1.177 0.208,0.219 10 false 5 2.542,0.969 2.938,1.177 0.396,0.208 10 false GND 5.156,0.938 5.365,1.156 0.208,0.219 10 false 5

CAUTION / NOTICE / HINT

NOTICE:

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


PROCEDURE

1.INSPECT PRE-CRASH SYSTEM CANCEL SWITCH ASSEMBLY
a.

Remove the pre-crash system cancel switch assembly (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM CANCEL SWITCH>REMOVAL).


b.

Inspect the pre-crash system cancel switch assembly (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM CANCEL SWITCH>INSPECTION)



OK

2.CHECK HARNESS AND CONNECTOR (PRE-CRASH SYSTEM CANCEL SWITCH ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)

NG

REPLACE PRE-CRASH SYSTEM CANCEL SWITCH ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (PRE-CRASH SYSTEM CANCEL SWITCH ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)
a.

Disconnect the E170 pre-crash system cancel switch assembly connector.


b.

Disconnect the E164 driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E170-8 (ECU) - E164-5 (PBSW) Pre-crash system cancel switch assembly off 10k Ω or higher
Pre-crash system cancel switch assembly on Below 1 Ω




OK

3.CHECK DRIVING SUPPORT ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK DRIVING SUPPORT ECU ASSEMBLY
a.

Replace the driving support ECU assembly with a new or known good one (See page Engine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU>REMOVAL)


b.

The pre-crash system cancel switch assembly is turned off.


c.

Check the PCS indicator light in the combination meter assembly.

OK:

The PCS indicator light will illuminate.




OK

END (DRIVING SUPPORT ECU ASSEMBLY WAS DEFECTIVE)

NG

REPLACE COMBINATION METER ASSEMBLY